1. Introduction
The Smart TPMS Diagnostic System, developed by LAUNCH, enables users to trigger TPMS sensors, program TPMS sensors, and perform TPMS relearning and diagnostics. It also supports sensor OE number lookup and all 10 modes of OBD II test for a complete diagnosis.
Moreover, it offers coding, reset, relearn, and other service functions to help vehicles get back to functional status after repair or replacement. This tool is specifically designed to work with all OBD II compliant vehicles.
To verify if a vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will designate “OBD II Certified”. Government regulations mandate that all OBD II compliant vehicles must have a “common” 16-pin Data Link Connector (DLC).
Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only those vehicles with a Vehicle Emissions Control Label stating “OBD II Certified” are OBD II compliant.
2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the test equipment, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- There are no user serviceable parts. Have the device serviced by a qualified repair person using only identical replacement parts. This will ensure the safety of the device is maintained. Disassembling the device will void the warranty.
- CAUTION: This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce, or dispose of the battery in fire or water.
- This product is not a toy. Do not allow children to play with or near this item.
- Do not expose the device to rain or wet conditions.
- Do not place the device on any unstable surface.
- Never leave the device unattended during charging. The device must be placed on a non-flammable surface during charging.
- Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Keep the tool dry, clean, free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the device when necessary.
- People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemakers could cause interference or failure.
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
3. Product Description
3.1 Components & Controls
The LAUNCH X431 Creader TPMS 5011 V2 features a robust design with intuitive controls.

Figure: LAUNCH X431 Creader TPMS 5011 V2 device with key features listed.
- Power button: Turn on/off the tool.
- Charging port: Charge the tool.
- Display screen: Indicate test results.
- DB-15 diagnostic connector: Connect the tool to the vehicle's Data Link Connector (DLC).
- TPMS antenna: For sensor interaction.
- Settings button: Quick access to the Settings module.
- HOME button: Navigate to the home (Job Menu) screen.
- BACK button: Exit the current program or return to the previous screen.
3.2 Technical Specifications
| Feature | Specification |
|---|---|
| Screen | 5" IPS, 1280*720 resolution |
| Input Voltage | 9 ~ 18V (OBD diagnostic port) / 5V (USB cable) |
| CPU | 1.3GHz, 4-core processor |
| RAM | 2GB |
| Storage | 32GB |
| Operating Temperature | 32°F~113°F (0°C~45°C) |
| Storage Temperature | -4°F~158°F (-20°C~70°C) @ RH60% |
| Communication Interface | OBD-II |
| Free Update Period | Lifetime |
| Battery Included | Yes |
| Wireless Support | Wifi |
| Special Features | Bluetooth |
| Software Update | Yes |
| Software Version | 2025 |
| Hardware Version | 2025 |
| Origin | Mainland China |
| Item Type | Code Readers & Scan Tools |
| Certification | CE, FCC |
3.3 Accessories Included
The following accessory items are included with your LAUNCH X431 Creader TPMS 5011 V2. Please note that for different destinations, the accessories may vary. For details, please consult from the seller.
- Smart TPMS diagnostic system x 1
- Diagnostic Cable x 1
- Charging Cable x 1
- Quick Start Guide x 1

Figure: Product packaging and included accessories.
4. Setup (Initial Use)
4.1 Charging & Turning On/Off
There are two methods available for charging the tool:
- Via PC: Connect one end of the charging cable to the charging port of the tool, and the other end to a PC or AC outlet with USB ports. Unplug the charging cable when finished.
- Via OBD Diagnostic Port (Not recommended): If the tool is properly connected to the vehicle's DLC (Data Link Connector) port, it will be charged automatically. Note: Attempting to charge the tool via OBD diagnostic port will consume the vehicle's battery power. This method is not recommended except for OBD diagnosis operations.
Press the power button
for about 3 seconds to turn it on/off. Press the power button for about 8 seconds to perform a forced shutdown.
4.2 Getting Started
If it is the first time you have used this tool, you need to make some system settings:
- Power on the tool. The screen displays a welcome page. Tap Start to go to the next step.
- Choose the desired system language, and tap Next.
- Choose the desired time zone, and tap Next to enter the WLAN setup screen.
- Slide the switch to ON; the system starts searching for all available wireless LANs. Choose the desired WLAN access point/network.
- If the network you chose is open, you can connect directly.
- If the selected network is encrypted, you have to enter the right security key (network password).
- After the network connection is done, tap Next Step to configure workshop information. Input the required information, and tap Next Step to go to the next step.
- Carefully read all terms and conditions of the user agreement, check the box before the "Agree to all the above terms", and tap OK to finish the sign-up process and navigate to the Job Menu.
4.3 Job Menu
The Job Menu includes the following function modules:

Figure: Job Menu screen.
- TPMS: Perform various TPMS operations, detect sensor data, and key frequency.
- Reset: Perform commonly used repair & maintenance services.
- OE Inquiry: Inquire about the original OE part number of the sensor and check applicable vehicle models.
- OBD II: Check for DTCs, isolate MIL causes, check monitor status, verify repairs, and perform other emission-related services.
- Upgrade: Update diagnostic software and APK.
- Data: Includes DTC library, DLC location, Image, Feedback, FAQ, and User Manual.
- Settings: Make adjustments and settings to the tool for your particular needs.
5. Operating Instructions
5.1 TPMS Operations
For initial use, follow the flow chart below to start using the TPMS functions:

Figure: TPMS Function overview.
1. Tap TPMS on the Job Menu screen to enter the vehicle selection screen.
5.1.1 Detect Sensor
This function allows you to check the sensor information of LAUNCH-specific sensors.
5.1.2 Detect Key
This function can detect the frequency of wireless vehicle keys.
5.1.3 Activate Sensor
This function allows users to activate TPMS sensors to view sensor data such as sensor ID, tire pressure, tire frequency, tire temperature, and battery condition.

Figure: Activation TPMS Sensor.
For universal sensors, place the TPMS antenna of the tool alongside the valve stem, point toward the sensor location, and tap Activate on the screen. Once the sensor information is successfully retrieved, the tool will sound a series of beeps, and the screen will display the sensor data.
Notes:
- For early magnet-activated sensors, place the magnet over the stem and then place the tool alongside the valve stem.
- If the TPMS sensor requires tire deflation (of the order of 10PSI), then deflate the tire and place the tool alongside the stem while tapping Activate on the screen.
- The tool will perform TPMS tests in a sequence of FL (Front Left), FR (Front Right), RR (Rear Right), LR (Rear Left), and SPARE (if applicable).
- If the sensor data is abnormal, it will be displayed in red.
If you intend to read the original sensor ID stored in the ECU, connect the tool to the vehicle's DLC via the diagnostic cable and tap Read ECU ID. After the sensor information is successfully decoded, the screen will appear with the sensor data.
5.1.4 Program Sensor
This function allows users to program sensor data to the LAUNCH-specific sensor, replacing faulty sensors or those with low battery life. The following options are available:

Figure: Programming TPMS Sensor options.
- Auto Create: Programs a LAUNCH-specific sensor with random IDs created according to the test vehicle when the original sensor ID is unavailable. Select the wheel, place a LAUNCH-specific sensor close to the TPMS antenna, and tap Auto. Then tap Programming to write the new ID.
- Manual Input: Allows users to manually enter a random or original sensor ID. Tap Manual, use the virtual keypad to input the ID, and tap OK. Select the wheel, place the sensor, and tap Programming to write the ID.
- Copy by Activation: Writes retrieved original sensor data to the LAUNCH-specific sensor after the original sensor has been triggered. Select the wheel position and tap Copy by Activation to retrieve the information. Place a LAUNCH-specific sensor close to the TPMS antenna and tap Programming.
- Copy by OBD: Writes saved sensor information to the LAUNCH-specific sensor after performing Read ECU ID. This requires a connection to the vehicle's DLC port. Tap Read ECU ID, connect to the DLC, and tap OK to read sensor IDs. Then tap the Programming tab to write the data.
5.1.5 Learning Service
This function allows you to check and view detailed TPMS sensor relearn procedures. Relearn operation applies only when newly programmed sensor IDs differ from the original sensor IDs stored in the vehicle's ECU. Relearn is used to write the newly programmed sensor IDs into the vehicle's ECU for sensor recognition.

Figure: TPMS Diagnosis with Relearn Methods.
On-screen buttons:
- Read DTC: Tap to read TPMS diagnostic trouble codes stored in the vehicle's ECU.
- Clear DTC: Tap to clear existing TPMS diagnostic trouble codes.
- OBD Relearning: Tap to write newly programmed sensor IDs into the vehicle's ECU via the vehicle's DLC socket.
Note: This function requires the tool to connect with the vehicle's OBD socket.
5.1.6 OE Inquiry
This function allows you to check the OE number of the sensors. Tap OE Inquiry on the Job Menu screen. Tap the target sensor manufacturer to enter. Check the original manufacturer number on the body of the sensor, and tap the corresponding OE number on the screen.
5.2 OBD II Diagnosis
This function provides a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform other emission-related services.

Figure: Full OBDII Function overview.
5.2.1 Connection
- Turn the ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to the DLC location diagram in Section 3.1.
- Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool, then tighten the captive screws.
Notes:
- A plastic DLC cover may be found for some vehicles; remove it before plugging the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you have problems connecting, rotate the connector 180° and try again.
4. Turn the ignition on. The engine can be off or running.
CAUTION: Do not connect or disconnect any test equipment with the ignition on or engine running.
5. The system automatically turns on and navigates to the main menu screen.
5.2.2 Start OBD Diagnostics
After the tool is properly connected to the vehicle's DLC, tap OBD II on the Job menu screen. The tool will start an automatic check of the vehicle's computer to determine the communication protocol and display the Monitor Status.
Note: A PROTOCOL is a set of rules and procedures for regulating data transmission between computers. Five different types of protocols (ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW, and CAN) are in use by vehicle manufacturers.
The OBD II Diagnosis functions include:
- I/M Readiness: Checks if emissions-related systems are operating properly and are ready for Inspection and Maintenance testing.
- Read Live Data: Retrieves and displays live data and parameters from the vehicle's ECU.
- Read Freeze Frame: Takes a snapshot of operating conditions when an emission-related fault occurs.
- Read Fault Code: Identifies which section of the emission control system has malfunctioned.
- Clear Fault Code: Erases codes from the vehicle after diagnosis and repairs. Ensure the ignition key is ON with the engine off before clearing codes.
- Test Results - On-board monitoring test: Retrieves test results for emission-related powertrain components not continuously monitored.
- Control Operations of On-board Component/System: Accesses vehicle-specific subsystem and component tests.
- Read Vehicle Information: Retrieves VIN, CID (Calibration ID), and CVN (Calibration Verification Number).
6. Maintenance
6.1 Firmware Fix
This option enables you to fix and repair the tire pressure firmware and the VCI firmware.
6.2 Upgrade
If new software or APK updates are available, a numeric indicator will display on the Upgrade module on the Job menu. Use this option to keep your tool synchronized with the latest version.

Figure: Upgrade screen showing available software updates.
Notes:
- To enjoy more functions and better service, it is strongly suggested to update regularly.
- This function requires a stable network connection.
Tap Upgrade on the Job menu to enter the update center. Tap Select All to select all diagnostic software. To deselect, tap Unselect and uncheck the box next to the vehicle model. Tap Update to start downloading. Once finished, the software packages will be installed automatically.
6.3 Clean Up
This option allows users to clear cache files and free up storage space. After cleanup, the tool will reboot automatically.
7. Settings
The Settings module allows you to customize the tool's behavior and preferences:
- Units of measurement: Set the measurement unit (Metric System and English System are available).
- Display/Brightness: Adjust standby time and screen brightness. (Reducing brightness helps conserve power).
- Sound: Adjust volume and other sound settings.
- Network: Configure WLAN settings to get online, register the tool, and update software. (Turn off WLAN when unused to save battery).
- Time Zone: Set the device's time zone.
- Language: Change the system language.
- Region (TPMS): Set the target region for TPMS sensor application.
- Workshop information: Add a personalized tag to diagnostic reports.
- Recovery: Reset the tool to default factory settings. (Warning: This may cause data loss).
- Screen Capture: Enable/disable a floating screenshot icon. Screenshots are saved under Data -> Image.
- About: Displays hardware configuration and license agreement information.
8. Troubleshooting (FAQ)
Here are some frequently asked questions and answers relating to this tool:
- Question: System halts when reading data stream. What is the reason?
Answer: It may be caused by a slackened connector. Please turn off the tool, firmly connect the connector, and switch it on again. - Question: Screen of main unit flashes at engine ignition start.
Answer: Caused by electromagnetic disturbing, and this is a normal phenomenon. - Question: There is no response when communicating with the on-board computer.
Answer: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature. - Question: Why are there so many fault codes?
Answer: Usually, it's caused by poor connection or fault circuit grounding.
9. User Tips
Based on user feedback, here are some tips for optimal use:
- The device is user-friendly, even for those without prior experience with similar tools. Its intuitive interface makes it easy to navigate and perform essential functions.
- For seasoned users, the abundant adjustable settings and functions provide comprehensive control and diagnostic capabilities.
- Always ensure a stable network connection during software updates to prevent interruptions and ensure proper installation.
- Regularly check for software updates to benefit from new functions and improved service.
10. Warranty and Support
10.1 Warranty
This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than intended, or used in a manner inconsistent with instructions. The exclusive remedy for any defective automotive meter is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects will be made by LAUNCH. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
10.2 Customer Service
If you have any questions on the operation of the unit, please contact the seller, or contact LAUNCH TECH. CO., LTD:
- Tel: +86-755-84527891
- E-mail: overseas.service@cnlaunch.com
A PDF version of the user manual is also available for detailed reference. You can find it at: User Manual (PDF)
11. Compliance Information
FCC and IC Compliance
FCC ID: XUJCRT511SV2
IC: 29886-CRT511SV2
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The SAR limit adopted by USA and Canada is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The highest SAR value reported to the Federal Communications Commission (FCC) and Industry Canada (IC) for this device type when tested for proper body-worn use is under 1g 1.6W/Kg.
This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.
12. Unboxing and Activation Video
Video: Unboxing and initial activation process for the LAUNCH Creader TPMS 5011 V2.