Introduction
This manual provides instructions for the proper use, maintenance, and replacement of accessories for your Philips AVENT Electric Breast Pump. These accessories are designed to maintain the optimal performance and hygiene of your breast pump. Please read these instructions carefully before use.
Product Overview
This product includes various replacement parts essential for the function of your Philips AVENT electric breast pump. These may include duckbill valves, diaphragms, and tubing.
Setup and Installation
- Initial Cleaning: Before first use, wash all new accessories thoroughly with warm soapy water and sterilize them according to the cleaning instructions below.
- Identify Part: Determine which part of your breast pump needs replacement (e.g., duckbill valve, diaphragm, tubing).
- Remove Old Part: Gently detach the worn or damaged part from your breast pump. Be careful not to damage other components.
- Install New Part:
- Duckbill Valve: Carefully push the new duckbill valve onto its designated connector on the pump body. Ensure it is seated firmly and flat for proper suction.
- Diaphragm: Place the silicone diaphragm onto the pump body, ensuring the edges are securely sealed all around. A proper seal is crucial for maintaining vacuum.
- Tubing: Connect one end of the tubing to the pump unit and the other end to the breast shield connector. Ensure connections are snug.
- Assemble Pump: Reassemble the rest of your breast pump components as per your original breast pump manual.
Operating Considerations
These accessories are designed to integrate seamlessly with your Philips AVENT electric breast pump. Once installed correctly, the pump should operate as described in your main breast pump manual. Ensure all connections are secure before each pumping session to maintain optimal suction and efficiency.
Maintenance and Care
Cleaning
- Immediately After Use: Disassemble all parts that come into contact with breast milk.
- Washing: Wash parts in warm water with mild dish soap. Use a soft brush for hard-to-reach areas. Rinse thoroughly with clean water.
- Drying: Air dry all components completely on a clean drying rack or use a clean cloth. Ensure parts are fully dry before storage to prevent mold or bacterial growth.
Sterilization
Regular sterilization is recommended for all parts that come into contact with breast milk.
- Boiling: Place parts in a pot of boiling water for 5 minutes.
- Steam Sterilizer: Use a microwave or electric steam sterilizer according to its instructions.
- UV Sterilizer: Follow the manufacturer's guidelines for UV sterilization.
Inspection
Regularly inspect all accessories for signs of wear, tear, discoloration, or damage. Replace parts immediately if any damage is observed to ensure hygiene and optimal pump performance.
Troubleshooting
- Loss of Suction:
- Check the duckbill valve for any tears or debris, and ensure it is seated correctly. A damaged or improperly seated valve is a common cause of suction loss.
- Inspect the silicone diaphragm for any tears or holes, and ensure it forms a complete seal around the pump body.
- Verify that all tubing connections are secure and that the tubing itself is not kinked, pinched, or damaged.
- Pump Not Working Efficiently: If suction is weak or inconsistent, review the above points. Ensure all parts are clean and dry before assembly.
Specifications
| Feature | Detail |
|---|---|
| Compatibility | Philips AVENT Electric Breast Pumps (Models: SCF902, SCF903, SCF301, SCF302) |
| Material (Duckbill Valve/Diaphragm) | Silicone |
| Material (Milk Storage Bottle) | PPSU (Polyphenylsulfone) |
| Tubing Length | 80 cm (if included) |
| High-concerned chemical | None |
User Tips
- Keep Spares: It's always a good idea to have spare duckbill valves and diaphragms on hand, as these are critical for pump function and can wear out over time.
- Regular Replacement: For optimal hygiene and performance, consider replacing silicone parts like duckbill valves and diaphragms every 2-3 months, or sooner if you notice any decrease in suction or visible damage.
- Dry Thoroughly: Ensure all parts are completely dry before storing or reassembling to prevent bacterial growth and maintain the integrity of the silicone.
Warranty and Support
These accessories are replacement parts for your Philips AVENT Electric Breast Pump. For any issues related to the quality or function of these specific replacement accessories, please contact the seller directly. For general breast pump operation or warranty information regarding your main breast pump unit, please refer to the original Philips AVENT product manual or contact Philips AVENT customer support.
