Flipsky 75100 / 75100 PRO

Contents

Flipsky 75100/75100 PRO FOC 75V 100A Single ESC User Manual

For Electric Skateboard, Scooter, and Ebike Speed Control

1. Introduction

This manual provides essential information for the safe and effective use of your Flipsky 75100 or 75100 PRO FOC 75V 100A Single ESC. Please read it thoroughly before installation and operation to ensure optimal performance and prevent damage.

Product overview video for the Flipsky 75100 ESC.

2. Safety Information

  • Always disconnect the battery before performing any wiring or maintenance.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate the ESC within its specified voltage and current limits.
  • Avoid exposing the ESC to water, excessive moisture, or extreme temperatures.
  • Improper configuration or wiring can lead to ESC damage or unsafe operation.
  • Keep out of reach of children.

3. Specifications

Feature Specification
Voltage Range14-84V (4-20S)
Continuous Current100A
Max Current120A
FirmwareLatest (firmware update supported)
ERPM150000
Control Interface PortsUSB, CAN, UART
BEC5V@1A
ModesDC, BLDC, FOC (sinusoidal)
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size12AWG
ProgrammableYes (via VESC_Tool)
Regenerative CapacityYes
MaterialComposite Material
ApplicationElectric Skateboard, Ebike

Dimensions:

  • Flipsky 75100: L85mm x W50.7mm x H33.8mm
  • Flipsky 75100 PRO: L103mm x W58mm x H27.7mm
Dimensions of the Flipsky 75100 ESC

Dimensions of the Flipsky 75100 ESC.

Dimensions of the Flipsky 75100 PRO ESC

Dimensions of the Flipsky 75100 PRO ESC.

4. Package Contents

  • 1x Flipsky 75100 or 75100 PRO ESC
  • 1x USB cable
  • 1x Hall sensor adapter (6-pins)
  • 1x User Manual

5. Setup & Installation

Before installation, ensure your battery is disconnected. Carefully follow the wiring diagrams provided below for your specific ESC model.

5.1. Wiring Diagram for Flipsky 75100

Wiring diagram for Flipsky 75100 ESC

Wiring diagram for Flipsky 75100 ESC, showing connections for USB, Hall, Comm, PPM, UART2, CAN, Battery, Motor, and Accelerator.

  • 1. USB: Connect to a computer for VESC_Tool configuration.
  • 2. HALL: Connect Hall sensors from the motor (if applicable).
  • 3. COMM: Communication port for external modules (e.g., Bluetooth).
  • 4. PPM: Connect for PPM remote control input.
  • 5. UART2: Connect for UART devices (e.g., display, remote receiver).
  • 6. CAN: Connect for CAN bus communication with other ESCs or devices.
  • BATTERY: Connect to your main battery pack. Ensure correct polarity.
  • MOTOR: Connect to your brushless motor's phase wires.
  • ACCELERATOR: Connect your throttle/accelerator input.

5.2. Wiring Diagram for Flipsky 75100 PRO

Wiring diagram for Flipsky 75100 PRO ESC

Wiring diagram for Flipsky 75100 PRO ESC, showing connections for CAN, Hall, SWD, PPM, USB, Comm, Battery, and Motor.

  • 1. CAN: Connect for CAN bus communication.
  • 2. HALL: Connect Hall sensors from the motor (if applicable).
  • 3. SWD: Debugging port.
  • 4. PPM: Connect for PPM remote control input.
  • 5. USB: Connect to a computer for VESC_Tool configuration.
  • 6. COMM: Communication port for external modules.
  • BATTERY: Connect to your main battery pack. Ensure correct polarity.
  • MOTOR: Connect to your brushless motor's phase wires.

Important: When unplugging connectors, always press the release tab to avoid pulling directly on wires and breaking connectors.

Top view of Flipsky FSESC75100 Pro with Alu. PCB, highlighting various connectors.

Top view of Flipsky FSESC75100 Pro with Aluminum PCB, highlighting various connectors.

Bottom view of Flipsky FSESC75100 Pro with Alu. PCB, showing heat sink design.

Bottom view of Flipsky FSESC75100 Pro with Aluminum PCB, showing heat sink design.

Internal view of the Flipsky FSESC75100 Pro PCB, showing electronic components.

Internal view of the Flipsky FSESC75100 Pro PCB, showing electronic components.

6. Configuration (VESC_Tool)

The Flipsky 75100/75100 PRO ESC is programmable via VESC_Tool, offering extensive customization and protection features.

6.1. Critical Configuration Tip: Phase Filtering

Phase filtering is NOT available for Flipsky ESC75100 and 75200 models.

  • When using firmware version 3.00 or newer in VESC_Tool, you MUST turn off the phase filter function and select "false".
  • Failure to turn off the phase filter will result in ESC damage.
  • Do NOT restore default parameters when using the wizard interface, as this may re-enable the phase filter.

For more detailed instructions and visual guides on VESC_Tool configuration, refer to the following resources:

7. Operation

Once the ESC is correctly wired and configured using VESC_Tool, you can begin operation. Ensure your battery is fully charged and all connections are secure before each use.

  • Power on your system (battery first, then remote/throttle).
  • Verify that the motor responds correctly to throttle input.
  • Monitor for any unusual sounds, smells, or excessive heat during initial tests.
  • Always operate your electric vehicle responsibly and within safe limits.

8. Maintenance

  • Regularly inspect all wiring and connectors for wear, damage, or loose connections.
  • Keep the ESC clean and free from dust, dirt, and debris.
  • Ensure adequate airflow around the ESC to prevent overheating, especially during demanding use.
  • Periodically check for firmware updates using VESC_Tool to benefit from improvements and bug fixes.

9. Troubleshooting

  • No Power/No Response: Check battery connections, power switch, and ensure the ESC is receiving power. Verify USB connection for VESC_Tool.
  • Motor Not Spinning: Check motor phase wire connections. Re-run motor detection in VESC_Tool. Ensure remote control is paired and functioning.
  • Erratic Motor Behavior: Re-check Hall sensor connections (if used). Ensure phase filter is disabled in VESC_Tool (critical for 75100/75200).
  • Overheat/Shutdown: Ensure proper ventilation. Check motor current limits in VESC_Tool. Reduce load or operating time.
  • ESC Damage after Firmware Update: This is often due to the phase filter setting. Ensure it was set to 'false' and not restored to default.

10. User Tips

  • Sensored vs. Sensorless Operation: The ESC supports both sensored (using Hall sensors) and sensorless motor operation. Sensored operation typically provides smoother startup and low-speed control. If your motor has Hall sensors, connect them; otherwise, the ESC can operate in sensorless mode after proper configuration in VESC_Tool.
  • Programmability: The ESC is highly programmable via VESC_Tool. This allows for fine-tuning parameters like motor current, battery current, braking strength, and input mapping. Take advantage of this feature to optimize performance for your specific setup (e.g., 60V scooter).
  • Firmware Updates: While firmware updates are supported, always exercise caution. Back up your current configuration before updating and carefully follow the instructions, especially regarding the phase filter setting.

11. Warranty & Support

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.

For additional resources and community support, consider visiting online forums dedicated to VESC-based ESCs and electric vehicle DIY projects.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.