Introduction
Thank you for choosing the Wancle Automatic Burr Coffee Grinder. This appliance is designed to provide a precise and consistent grind for various brewing methods, enhancing your daily coffee experience. With 28 precise grind settings, it effortlessly transforms beans into aromatic excellence. Please read this instruction manual carefully before using the appliance for the first time and retain it for future reference.
This manual covers models CBG-8000, CBG-8002, and CBG-8003.
Important Safety Instructions
Failure to follow these safety instructions may result in injury or damage to the appliance.
- Please read the instructions for use carefully before using your appliance for the first time and retain them for future reference. Wancle cannot accept any liability for non-compliant appliance use.
- Do not use the appliance if it has been dropped and there is visible damage to it (e.g., the protection panel), or if it fails to function normally. In this case, it must be sent to an approved service center.
- If the power cable is damaged, it must be replaced by the manufacturer, an approved service center, or a similarly qualified person, to avoid danger.
- Always unplug the appliance as soon as you stop using it, if you leave it unattended or during assembly, disassembly, or cleaning.
- This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
- This appliance may be used by persons with a lack of experience and knowledge or reduced physical, sensory, or mental capabilities, as long as they are supervised or have been instructed about using the appliance safely and are fully aware of the dangers involved.
- Children shall not play with the appliance.
- Please handle the knife with care when the container is empty and during cleaning; the blades are very sharp.
- Check that your power supply voltage corresponds to that shown on the appliance (alternating current only). Any error in plugging in your appliance may cause irreversible damage and invalidate the guarantee.
- This appliance is not intended to be used by persons (including children) with reduced physical, sensory, or mental capacities, or persons lacking in experience or knowledge, unless they are supervised or have been instructed about using the appliance by a person responsible for their security.
- In the interests of safety, only use Wancle accessories and spare parts designed for your appliance.
- Warning: Any misuse could lead to potential injury.
- Warning: The appliance must not be immersed in water or any other liquid.
- This appliance is intended for indoor, domestic household use only. It is not intended to be used in the following applications, and the guarantee will not apply for: staff kitchen areas in shops, offices, and other working environments; farmhouses; by clients in hotels, motels, and other residential type environments; bed and breakfast type environments.
- Refer to the instructions for initial and regular cleaning of surfaces in contact with foodstuff and for cleaning and maintenance of your appliance.
Product Overview
Familiarize yourself with the components of your Wancle coffee grinder:
Components:
| Label | Component |
|---|---|
| A | Bean hopper |
| B | Bean hopper lid |
| C | Body of appliance |
| D | Switch (ON/OFF) |
| E | Removable upper mill |
| F | Ground coffee holder |
| G | Ground coffee holder lid |
| H | Number of cups selector |
| I | Grind setting |
| J | Ground coffee dispenser |
Before First Use
Before using your Wancle coffee grinder for the first time, please follow these steps:
- Clean the ground coffee holder, its lid, and the bean hopper lid with warm, soapy water.
- Clean the inside of the bean hopper with a damp cloth.
- Never place the body of the appliance in water or under running water.
- Carefully dry all assembled parts and fit them to the appliance again.
Setup and Assembly
Follow these steps to set up your coffee grinder:
- Fit the ground coffee holder (F) and its lid (G) in their correct positions. Check that the assembly is correctly positioned in the body (C).
- Remove the bean hopper lid (B) and put coffee beans into the bean hopper (A). Replace the bean hopper lid and make certain that it is correctly positioned.
- Set the quantity of ground coffee you want by positioning the number of cups selector (H) according to the desired quantity.
- Set the ground coffee fineness by adjusting the grind setting selector (I) to the desired level.
Operating Instructions
- Plug in the appliance.
- Press the ON/OFF switch (D) to start the appliance.
- Once the selected quantity has been milled, the appliance will stop automatically.
- If you want to stop the appliance before it finishes, press the ON/OFF switch again.
- Remove the ground coffee holder (F), tap the receptacle gently, remove the lid (G), and pour the ground coffee obtained directly into the filter of your coffee maker or use a measuring spoon to fill an espresso coffee maker.
- To obtain additional ground coffee, you can repeat an operating cycle by again pressing the ON/OFF switch. Always ensure that the ground coffee does not go above the "max." level of the ground coffee holder. Selected settings will be retained from one use to the next.
Caution!
For your appliance to run correctly, make certain that:
- The bean hopper lid (B) is correctly positioned.
- The ground coffee holder (F) and its lid (G) are correctly placed in the body of the appliance (C).
Grind Settings Advice
Use the grind setting selector to adjust the level of fineness of your ground coffee according to the type of coffee maker you use and to your taste. On first use, you are advised to select an intermediate position according to your type of coffee maker and then later adjust the degree of fineness to your taste. Once you have used the appliance a few times, you will find the ideal grind to suit you. Do not change the grind setting when the mill is running.
Advice to select the number of cups:
Use the number of cups selector to program the quantity of ground coffee you want. The more cups you select, the longer the appliance will run.
Advice about coffee:
- The aroma of coffee depends on the quality of the grind.
- Generally, the quicker the coffee-making technique, the finer the ground coffee should be.
- The grind used for an espresso is therefore finer than that for a filter coffee.
- A very fine ground coffee intended for espresso will give you a bitter-tasting coffee when used for a filter coffee.
- Using a coarser grind for an espresso coffee will give you a weak-tasting coffee.
- Once you have chosen the appropriate coffee ground fineness for your coffee-maker, you can just add more ground coffee to get a stronger taste without any additional bitterness.
Grind Recommendations Table:
| Gear | 1~4 | 5~8 | 9~13 | 14~18 | 19~23 | 24~28 |
|---|---|---|---|---|---|---|
| Thickness | Extra Fine | Slightly Fine | Fine | Medium | Coarse | Very coarse |
| Suitable for | Italian | Moka pot | Siphon pot or ice brew | Drip pot | Hand pouring | French press |
| Concentration | Extra Thick | Thick | Medium Thick | Light | Light | Light |
Maintenance
Proper maintenance ensures the longevity and optimal performance of your grinder.
- Always unplug your appliance before cleaning.
- Never place the body of the appliance, power supply cord, or plug in water or under running water.
- Do not use detergents or abrasive pads to clean the appliance.
- Clean the lids and the ground coffee holder in warm, soapy water, or place them in the upper basket of your dishwasher.
- Over time, the color of the coffee beans may stain the plastic parts of your appliance; this is normal.
- They may be cleaned by soaking them in mild bleach (non-abrasive) straight after use.
Disassemble the upper grinding head:
- Please turn the funnel counterclockwise to the end. At this time, the arrow on the body is aligned with the arrow on the funnel (Figure 11), and remove the funnel (8).
- Rotate the upper grinding head clockwise until you hear a "pop" sound, then lift it vertically to remove it (9).
- Use a damp cloth to carefully clean the inside of the bean hopper.
- Install funnel (Picture 10). Rotate the upper grinding head counterclockwise to the end. At this time, the handle of the upper grinding head is aligned with the arrow on the main body (Picture 12). Insert the funnel with the arrow on the body aligned with the arrow on the main body (Figure 11), then rotate the funnel clockwise to the desired position.
- Carefully clean the ground coffee dispenser and the body of the appliance using a damp cloth.
Notice for Assembly:
- When disassembling and installing the funnel of the flat grinder coffee machine, please align the arrow on the coffee funnel with the arrow on the top of the body, so that the funnel can be taken out or installed.
- The grinding head alignment arrow indicates that the grinding head is locked. Only then can the funnel be assembled.
Troubleshooting
The appliance does not operate or stops during operation:
- Check the electrical connection.
- The bean hopper is not positioned correctly.
- The ground coffee holder or its lid is not positioned correctly or not fitted.
The grind selector no longer works:
- Check that the upper mill is correctly positioned. (See paragraph on maintenance in the user's manual).
Common Questions & Answers:
- Q: Why does the number of cups produced by the coffee powder be less than the setting?
A: The larger the coffee beans, the more space they take up and the less coffee powder they can grind. The coarser the coffee powder you set, the more cups you can get. - Q: Why does the noise get louder the finer the coffee powder is set?
A: The finer the coffee powder is set, the closer the two grinding heads are, the longer the grinding time is, and the louder the noise is. But the ground coffee powder is finer and more uniform. - Q: Why doesn't the grinder start after pressing the power button?
A: 1. The grinder head and coffee bean hopper are not installed correctly. 2. The power button is touched too lightly and the switch spring is not pressed into place. - Q: Why does the coffee machine suddenly stop during grinding?
A: The Wancle flat grinder has an overheat protection system. It takes about 10 minutes to cool down before it can be restarted.
Specifications
| Feature | Detail |
|---|---|
| Model | CBG-8000/CBG-8002/CBG-8003 |
| Power | 120 VAC / 60 Hz (US) 200W, 220-240 VAC (50/60 Hz) (EU) 200W |
| Product Weight | 0.9kg (1.98lb) |
| Product Size | 150x90x182mm (5.9x3.5x7.2in) |
| Housing Material | Stainless Steel |
| Grinding Levels | 28 Precise Grind Settings |
| Bean Container Capacity | 3 oz (80g) |
| Cup Count Control | 2~12 cups |
| Type | Burr Grinders (Flat Wheel) |
| Certification | ETL, CE, EMC, RoHS |
Power & Plug Compatibility:
User Tips
- For optimal aroma: Keep your coffee beans in the refrigerator in a sealed container. To preserve the full aroma of your coffee, we advise you to grind your coffee just a few moments before making it.
- Grind consistency: The finer the coffee powder is set, the closer the two grinding heads are, which results in a finer and more uniform grind, though it may increase noise.
- Overheat protection: If the grinder stops unexpectedly, it might be due to the overheat protection system. Allow it to cool down for about 10 minutes before restarting.
- Starting issues: Ensure the grinder head and coffee bean hopper are correctly installed and that the power button is pressed firmly to engage the switch spring.
Warranty and Support
Wancle Limited Guarantee:
- Wancle guarantees this product against any manufacturing defect in materials or workmanship for 1 year, starting from the initial date of purchase or delivery date.
- This manufacturer's commercial guarantee covers all costs related to restoring the proven defective product so that it conforms to its original specifications, through the repair or replacement of any defective part and the necessary labor.
- At Wancle's choice, a replacement product may be provided instead of repairing a defective product.
- Wancle's sole obligation and your exclusive resolution under this guarantee are limited to such repair or replacement.
Conditions & Exclusions:
- Wancle shall not be obliged to repair or replace any product which is not accompanied by a valid proof of purchase.
- The defective product may be returned to the store of purchase.
- This guarantee applies only for products purchased and used for domestic purposes and will not cover any damage which occurs as a result of misuse, negligence, failure to follow Wancle instructions, or a modification or unauthorized repair of the product, faulty packaging by the owner, or mishandling by any carrier.
- It also does not cover normal wear and tear, maintenance or replacement of consumable parts, or the following: using the wrong type of water or consumable, mechanical damages, overloading, damages or poor results specifically due to wrong voltage or frequency as stamped on the product ID or specification, the ingress of water, dust, or insects into the product, scaling (any de-scaling must be carried out according to the instructions for use), damage as a result of lightning or power surges, damage to any glass or porcelain ware in the product, accidents including fire, flood, etc., professional or commercial use.
Consumer Statutory Rights:
- Wancle's commercial guarantee does not affect the Statutory Rights a consumer may have or those rights that cannot be excluded or limited, nor rights against the retailer from which the consumer purchased the product.
- This guarantee gives a consumer specific legal rights, and the consumer may also have other legal rights which vary from Country to Country.
- The consumer may assert any such rights at his sole discretion.
Contact Support:
- Company Name: Dongguan Pinle Electronic Technology Co., Ltd
- Company Address: tangxiazhen, tangxiadiyigongyelu, 11hao304shi, dongguan, guangdong, 523710, CN
- Email: support@wancle.net
- Website: www.wancle.net
- Quick Response: If you have any questions about the product, please contact customer service, and we will provide you with a professional and fast response within 24 hours.