1. Product Overview
The SpeedyBee Mario 5 Frame is a high-performance carbon fiber frame designed for 5-inch FPV freestyle and racing drones. It is available in DC (Dead Cat) and XH (Squashed X) versions, offering compatibility with various FPV systems including DJI O3 Air Unit, O4 Air Unit Pro, and analog VTX.
Video: SpeedyBee Mario 5 Frame Product Overview
The frame features a unique support structure, power dual input method, and a high-strength aviation aluminum alloy head for enhanced durability and performance.
Image: DIY Free Combination options for Mario 5 DC Lite, Advanced, and PRO versions.
2. Package Contents
The SpeedyBee Mario 5 Frame Kit comes with the following components. Please verify all parts are present upon unboxing.
2.1 Mario 5 DC Lite Version
Image: Mario 5 DC Lite Package Contents
2.2 Mario 5 Upgrade Kit A (Optional)
Image: Mario 5 Upgrade Kit A Package Contents
3. Setup and Assembly
Assembling the SpeedyBee Mario 5 Frame requires careful attention to detail. It is recommended to lay out all components and identify them before beginning assembly.
3.1 General Assembly Steps
- Unpack all components and verify against the package contents list.
- Identify all screws and hardware. Note that screw packages may not be labeled, requiring careful sorting.
- Assemble the main carbon fiber plates (top, middle, bottom) and arms using the provided aluminum columns and screws.
- Install the motor protective pads and receiver protective cover.
- Mount the camera silicone mount and the aviation aluminum alloy head.
- Integrate your flight controller (FC), electronic speed controller (ESC), video transmitter (VTX), and receiver into the frame.
- Attach the battery anti-slip pad.
- If using the Upgrade Kit, install the TPU mounts for GoPro, XT60/SMA antenna, and receiver as needed.
3.2 Key Features for Assembly
- Unique Support Structure: Enhances body stability and accommodates capacitor installation. Supports dual-directional installation for capacitors (up to Φ10mm*20mm).
- Power Dual Input Method: Allows for easy adjustment of the drone's center of gravity with integrated socket and antenna for neater installation.
- High-Strength Alloy Head: Designed to protect the lens, minimize high-frequency 'Jello effect' for a steadier image, and offers a recessed GoPro mount for a lower center of gravity.
- Receiver Installation Space: The rear bottom area is dedicated for receiver installation (25mm*13mm*6mm). A translucent protective cover simplifies receiver binding and provides clear visibility of receiver lights.
- Frame Protection Armor: Consists of two sections to protect the FC and enhance DJI O3 VTX cooling capacity.
- Lightweight Protective Footpads: Injection-molded footpads minimize inertia while protecting motors and the frame. Compatible with motors having 16-19mm hole spacing.
Image: Unique Support Structure and Power Dual Input Method
Image: High-Strength Alloy Head Features
Image: Frame Protection Armor and Protective Footpads
Image: Receiver Installation Space and 3D Model Customization
4. Operating Considerations
The Mario 5 Frame is designed to be the structural foundation for your FPV drone. Proper selection and installation of electronic components are crucial for optimal flight performance.
- Propeller Compatibility: Ensure propellers do not exceed 5.1 inches in size.
- Camera Compatibility: The frame supports 19mm and 20mm cameras, including DJI O3 Air Unit, O4 Air Unit Pro, and various analog VTX systems.
- Component Mounting: Utilize the designated mounting holes for your Flight Controller (FC: 30.5x30.5 M3) and Video Transmitter (VTX: 20x20 M2 / 25.5x25.5 M2).
- Weight Distribution: Pay attention to component placement to achieve a balanced center of gravity for stable flight.
5. Maintenance
Regular maintenance will ensure the longevity and safety of your SpeedyBee Mario 5 Frame.
- Inspect Carbon Fiber Plates: Periodically check the top, middle, bottom plates, and arms for any cracks or damage, especially after crashes. Replace damaged parts immediately.
- Check Screws and Fasteners: Ensure all screws (M3*16, M3*25, M2*4, M2*7, M3*6, M3*12, M5*22, M4*3) are tight. Loose screws can lead to vibrations or component detachment during flight.
- Clean Components: Keep the frame and mounted electronics free from dirt, dust, and debris. Use compressed air or a soft brush.
- TPU Parts Inspection: Check TPU mounts and protective parts for wear and tear. Replace if they become brittle or damaged.
- Aluminum Columns: Inspect the aviation aluminum alloy columns for bends or damage.
6. Troubleshooting
- Missing Parts: If you find any parts missing from your package, contact the seller or manufacturer's support immediately.
- Difficulty in Assembly: The assembly process can be intricate for beginners. Refer to online video tutorials or seek assistance from experienced FPV builders.
- Unlabeled Screws: Some screw packages may not be labeled. Carefully sort and identify screws by size and type before assembly to avoid confusion.
- "Jello Effect" in Video Feed: Ensure your HD VTX is properly mounted and secured. The frame's high-strength alloy head is designed to minimize this effect. Check for loose components or vibrations.
7. Specifications
| Feature | Specification |
|---|---|
| Model | SpeedyBee Mario 5 Frame |
| Mario 5 DC Wheelbase | 227mm |
| Mario 5 DC Weight (3D Printed Parts Excluded) | 129 ±5g |
| Mario 5 DC Weight (3D Printed Parts and Injection) | 170 ±5g |
| Mario 5 XH Wheelbase | 226mm |
| Mario 5 XH Weight (3D Printed Parts Excluded) | 126 ±5g |
| Mario 5 XH Weight (3D Printed Parts and Injection) | 167±5g |
| Top Plate Thickness | 2.5mm (T300 3K) |
| Middle Plate Thickness | 2.0mm (T300 3K) |
| Bottom Plate Thickness | 2.5mm (T300 3K) |
| Arm Thickness | 6mm (T300 3K) |
| Camera Mounting Screw | 7mm |
| 3D Printed Parts Material | Yellow TPU |
| Battery Anti-Slip Pad | Silicone 3mm |
| Motor Spring Hole Position | Φ8mm |
| Compatible Propeller Size | Max 5.1 Inch |
| Motor Mounting Hole Distance | 16-19mm |
| FC Mounting Hole | 30.5x30.5 (M3) |
| VTX Mounting Hole | 20x20 (M2) / 25.5x25.5 (M2) |
| Head Material | Aviation Aluminum Alloy |
| Aluminum Column Material | 7075 D5*23mm / D46*22mm |
| Internal Mounting Height | 23-31mm |
| Receiver Installation Space | 25*13*6mm |
| Suitable Capacitor Size | Φ10mm*20mm |
| GPS Installation Size | 18*18*7 |
| Camera Compatibility | 19mm / 20mm |
8. User Tips
- Video Tutorials: For beginners, it is highly recommended to watch two or three video tutorials on FPV drone frame assembly before starting.
- Component Placement: Pay close attention to the positioning of critical components like the capacitor and radio receiver, especially between the lower plates, to ensure proper fit and function.
- Soldering: Be precise when soldering the main power (VBAT and GND) of the XT60 connector to the main pads of the ESC.
- Customization: The frame supports diverse open-source 3D models. Many TPU accessories are available for purchase or can be 3D printed from sites like Thingiverse to suit special needs or aesthetic preferences.
- Camera Fit: A 19x19mm FPV analog camera should fit perfectly, as the frame is compatible with 19mm/20mm cameras.
9. Warranty and Support
For warranty information, technical support, or inquiries regarding missing parts, please contact the seller or the official SpeedyBee customer service. Keep your purchase records for any warranty claims.