ETENWOLF V3

Contents

ETENWOLF ZEPHYR V3 Portable Air Compressor User Manual

Model: ZEPHYR V3

Introduction

Thank you for choosing the ETENWOLF ZEPHYR V3 Air Compressor. This portable power station pump is designed to inflate a wide range of tires and inflatables, enhancing versatility for your outdoor adventures. Please read all instructions and safety warnings before use to reduce the risk of electric shock, fire, and/or serious injury.

Warning! Please read all safety warnings and all instructions to reduce the risk of electric shock, fire and/or serious injury.

Package Contents

The ETENWOLF ZEPHYR V3 Air Compressor package includes the following items:

  • 1 x Zephyr V3 Air Compressor
  • 1 x Air Chuck
  • 1 x USB A to C Cable
  • 1 x User Manual
  • 1 x 15W charger
  • 1 x Cone shaped blowing nozzle
  • 1 x Ball needle
  • 1 x French copper adapter
  • 1 x T-shaped quick connector
Image showing all items included in the ETENWOLF Zephyr V3 Air Compressor package: the inflator, charger, USB-A to C cable, air chuck, cone nozzle, ball needle, French copper adapter, T-shaped quick connector, and user manual.
All items included in the ETENWOLF Zephyr V3 Air Compressor package.

Product Overview

Familiarize yourself with the components and controls of your Zephyr V3 Air Compressor:

Diagram of the ETENWOLF Zephyr V3 Air Compressor with labeled parts including Light button, Mode button, Plus button, Start/Pause button, Center display, Minus button, LED work light, Type-C input port, USB-A output port, Pressure hose, Presta valve adapter, Inflation needle, High-pressure tapered nozzle, Manual mode, Car mode, Bicycle mode, Ball mode, Pressure unit, Target input value, Actual pressure value, Safety alert symbol, and Battery level indicator.
Detailed overview of the Zephyr V3 Air Compressor components and display.

Component List:

  1. Light button
  2. Mode button (Switchable Units)
  3. "+" increase pressure button
  4. Start/pause power button
  5. Center display
  6. "-" decrease pressure button
  7. LED work light
  8. Type-C port (Input)
  9. USB-A port (Output)
  10. Pressure hose
  11. Presta valve adapter
  12. Inflation needle
  13. High-pressure tapered nozzle
  14. Manual mode
  15. Car mode
  16. Bicycle mode
  17. Ball mode
  18. Pressure unit
  19. Target input value
  20. Actual pressure value
  21. Safety alert symbol
  22. Battery level indicator

Setup and First Use

Follow these steps to prepare your Zephyr V3 for inflation:

  1. Remove the Pressure Hose: Take the pressure hose (10) from its storage channel.
  2. Connect the Nozzle: Insert the nozzle (10) clockwise into the object being inflated.
  3. Activate the Machine: Press the Start/pause power button (04) to turn on the compressor.
  4. Select Mode: Press the Mode button (02) to switch between Manual (14), Car (15), Bicycle (16), or Ball (17) modes.
  5. Select Pressure Unit: Press and hold the Mode button (02) for more than 1 second to cycle through PSI, KPa, and Bar units.
  6. Set Target Pressure: Use the "-" button (06) to decrease or "+" button (03) to increase the target pressure value.
  7. Start Inflation: Press the Start/pause power button (04) again to begin inflating.
  8. Automatic Shut-off: The unit will automatically turn off once the preset pressure value is reached.
Four-step visual guide for using the ETENWOLF Zephyr V3: 1. Remove the valve cap and connect the hose. 2. Long press for three seconds to start up. 3. Press M to select the mode. 4. Press start to inflate. Also shows product dimensions: 17.4cm height, 13.4cm width, 9.6cm depth, and 90cm hose length.
Easy-to-use steps for inflation and product dimensions.

Accessory Storage:

The Presta valve adapter (11), inflation needle (12), and high-pressure tapered nozzle (13) are conveniently stored on the back side panel of the compressor.

Close-up view of the ETENWOLF Zephyr V3 showing the integrated storage for various nozzles and adapters on the side of the device.
Integrated storage for inflation accessories.

Operating Instructions

Button Operation Guide:

  • MODE Button (02): Press briefly to switch between Car, Bicycle, Ball, and Manual inflation modes. Press and hold for more than 1 second to select the pressure unit (PSI, KPa, Bar).
  • Start/Pause Power Button (04): Long-press for two seconds to turn the inflator ON or OFF. Press briefly during inflation to pause or resume.

Automatic Shut-off Conditions:

The inflator will automatically turn off in the following cases:

  • After 3 minutes of inactivity.
  • If the charging cable is accidentally disconnected during charging.
  • After 5 minutes of inactivity once fully charged.
  • After 5 minutes of inactivity when used as a power bank.
  • If inflating for over 5 minutes and the actual pressure is still below 5 PSI.
  • If inflating for over 5 minutes and the actual pressure is above 150 PSI.

Preset Pressure Values:

The display shows the target input value (19) in smaller font and the actual pressure value (20) in larger font. The unit remembers your last pressure setting.

ModeAdjustable Pressure RangeDefault Pressure
Manual mode3-160 PSI30 PSI
Car mode8-130 PSI35 PSI
Bicycle mode10-145 PSI22 PSI
Ball mode3-16 PSI8.5 PSI

LED Work Light (07):

The LED work light is located on the front of the inflator. To turn it on, first power on the machine (04), then press the Light button (01). It has four modes: Bright flashlight, Ultra-bright flash light, Slow strobe light, and SOS light. The light automatically turns off after 1 hour (first use). Subsequent uses require manual turn-off.

Power Bank Function:

The Zephyr V3 can charge electronic devices via its USB-A output port (09) (5V 2A, 10W). The inflator must be powered on to function as a power bank. After 3 minutes of charging, the display will only show the battery level to conserve power. It will automatically turn off after 2 minutes of fully charging the connected device.

Pressure Recalibration:

Altitude changes can affect pressure readings (1-3 PSI variance). To recalibrate the pump's pressure sensor for high-altitude areas (above 5000 ft/1524 meters):

  1. Power on the pump (04).
  2. Hold the Light button (01) and Mode button (02) for 10 seconds.
  3. The entire screen will flicker, indicating recalibration is complete.

Note: Power off the pump before calibration. The pressure hose (10) must not be connected to any item that would apply pressure. A charged battery or other power source is required. New settings are not saved; the unit resets to sea level calibration (0 ft/meters) after power off.

Demonstration video showing the ETENWOLF Zephyr V3 inflating car, bicycle, and basketball tires, its power bank functionality, and LED light operation.

Maintenance and Safety

General Safety Guidelines:

  • This product is not a toy and should not be used by children. Users must be above 16 years old. Keep a safe distance between children and the inflator during operation.
  • The product contains a built-in lithium battery. Do not place the product into fire or dispose of the battery improperly.
  • Avoid overheating or water ingress, which can increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it in a hot car for prolonged periods. If the inflator becomes very hot, there is a risk of explosion.
  • The product has a built-in DC motor that may generate sparks. Do not use it in environments with dust or gas that are liable to explode.
  • If you hear unusual noise or the temperature becomes very high during inflation, turn off the inflator immediately.
  • Always ensure the correct pressure unit (PSI, Bar) is selected before setting the inflation pressure value to avoid dangerous overinflation.
  • Do not leave the pump unattended while it is in operation.
  • Use the product in a dry and clean environment. Do not wash the product with water, as sand and dust intrusion can damage it.
  • To reduce the risk of electric shock, do not expose the product to rain. Store indoors.

Battery Charging and Care:

  • For optimal charging performance and stability, use a 5V 3A 15W PD charger to fuel the built-in battery. Full charging from 0% to 100% takes approximately 2-3 hours.
  • The battery level indicator (22) shows capacity in four bars, each representing 25%.
  • The inflator cannot be used while it is charging.
  • Store the product within temperatures ranging from -10°C to 60°C (14°F to 140°F). Extremely hot or cold environments can damage the battery and shorten the inflator's lifespan.
  • For long-term storage, charge the inflator at least once every three months to maintain its performance.
  • Use only certified PD chargers and the included charging cable. Malfunctions caused by non-compliance with these requirements are not covered by the warranty.

Troubleshooting

Refer to the table below for common issues and their solutions:

ProblemSolution
Slow inflation speedCheck for leaks in the item, ensure air nozzle connection is tight, check for broken inflation hoses, and ensure ventilation slots are not blocked.
Air compressor turns on, but does not inflateThe pressure of the item being inflated may exceed the preset pressure.
Unable to increase or decrease the preset pressureEnsure the correct mode is chosen and the preset value is within range. Select manual mode to adjust pressure between 3-160 PSI.
Inflator inflates but display shows zero pressureIf air pressure is under 3 PSI, the display will show zero due to the pump's minimum pressure range.
Battery level indicator not shown after chargingUse a certified charger or standard charger and the included charging cable.
Air leakage when connecting high-pressure air hoseTighten the air nozzle.
Unable to charge other devicesCheck if the battery is sufficient. Verify charging device compatibility (5V 3A output). Cannot be used as a power source while charging. Use original charging cable.
Safety alert symbol light E08 error codeIf the issue persists after shutting down and restarting, send the device for factory repair.
E10 error code (Motor malfunction)Motor has ceased to function. If flashing for 30 seconds doesn't resolve, or issue persists after restart, send for factory repair.
E11 error code (Low-temp charging protection)Temperature during charging is too low. Restore temperature to above 0°C before continuing.
E12 error code (High-temp charging protection)Temperature during charging is too high. Restore temperature to below 45°C before continuing.
E13 error code (Low-temp discharge protection)Temperature is too low during inflation or charging other devices. Restore temperature to above -20°C before continuing.
E14 error code (High-temp discharge protection)Temperature is too high during inflation or charging other devices. Restore temperature to below 58°C before continuing.
E15 error code (Air pump exceeded working time)Warning icon flashes for 30 seconds then returns to normal. Check for leaks in the inflated item.
E16 error code (Overpressure protection)Returns to normal after pressure release.
E17 error code (High-pressure operation exceeded working time)Warning icon flashes for 30 seconds then returns to normal. Check if the inflated item is functioning abnormally.
E18 error code (Battery damage)Battery damage warning icon and battery level indicator icon flash for 30 seconds, then device shuts down. Send for factory repair.

Specifications

FeatureDetail
ModelZephyr V3 Air Compressor
Dimensions128 x 102 x 180 mm (5.04 x 4.02 x 7.09 inches)
Item Weight1.2 kg (2.65 lbs)
Inflation Pressure Range3-160 PSI / 0.2-11 Bar
Operating Temperature (Charging)0°C-45°C (32°F-113°F)
Operating Temperature (Discharging)-20°C-74°C (-4°F-165°F)
Storage Temperature-10°C-60°C (14°F-140°F)
High Pressure Air Tube Length0.9 meters (35.4 inches)
Battery Capacity7800mAh
Working NoiseLower than 85dB within 1 meter
InputType-C: 5V 3A
OutputUSB-A: 5V 2A
Charging Time2-3 hours
Continuous Working TimeApproximately 25 minutes at 20-50 PSI (at 25°C ambient temperature, under full charge)
Sensor Accuracy±1 PSI
Infographic comparing ETENWOLF V3 features like 7800mAh battery, <1 min inflation for ordinary car tires, continuous inflation without burning, idle for a year without power loss, ten-year life, and hands-free operation, against ordinary cells with 4000mAh, >2 min refill, charging stops, regular charging needed, short-lived, and not convenient.
Key advantages of the ETENWOLF Zephyr V3 compared to ordinary air compressors.
Comparison table of ETENWOLF models V3, S3, and S3C, detailing battery capacity (7800mAh for all), PSI (160PSI for all), inflation speed (22L/Min for V3/S3C, 35L/Min for S3), presence of snuffle valve, storage bag, and press light.
Model comparison: Zephyr V3, S3, and S3C.

Warranty and Support

2-Year Warranty Coverage:

Within two years of purchase, we provide timely and effective online after-sale service. We will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Information:

If you have any questions or comments, please contact us at: support@etenwolf.com

For a detailed user manual in PDF format, you can refer to the official document: Zephyr V3 User Manual (PDF)

User Tips

  • For optimal performance, ensure the inflator is fully charged before extended use, especially for multiple or larger tires.
  • Always double-check the selected pressure unit and target pressure value to prevent over-inflation or under-inflation.
  • When inflating bicycle tires, quickly remove the hose after reaching the desired pressure to minimize air loss.
  • The power bank feature is useful for emergencies, but remember the inflator needs to be powered on to charge other devices.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.