Tuya TY-12W-vdevo

Contents

Tuya 12-Channel WiFi/Zigbee Smart Switch Instruction Manual

Model: TY-12W-vdevo | Brand: Tuya

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Tuya 12-Channel WiFi/Zigbee Smart Switch. This versatile wireless relay module supports WiFi and Zigbee connectivity, along with a 433MHz RF remote control, enabling various control modes such as interlock, jog, and multi-scenario automation. Please read this manual thoroughly before use to ensure proper functionality and safety.

2. Safety Information

  • WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
  • NO LIVE INSTALLATION: Always disconnect power before performing any wiring or installation procedures. Failure to do so may result in electric shock, injury, or death.
  • Ensure all wiring is connected correctly and securely according to the instructions.
  • Do not expose the device to moisture or extreme temperatures.

3. Specifications

FeatureDetail
Input VoltageDC7V~27V / AC85-250V or Type-C 5V
Maximum Power220V/2200W
Wireless StandardWi-Fi 2.4GHz b/g/n + Bluetooth or Zigbee
Radio FrequencyRF433Mhz
Working Temperature-20℃~70℃
Relay TypeJQC-3FF (10A 277VAC / 12A 125VAC)
Dimensions100mm x 100mm x 20mm (approximate)

The module features 12 channels, each controlled by a JQC-3FF relay. The board includes a remote chip, working power supply, and a step-down board. Optional 433MHz reception is available.

Detailed diagram of the Tuya 12-Channel Smart Switch module with labeled components and dimensions.

Figure 1: Detailed view of the module with component labels and dimensions.

PCB dimensions diagram for the Tuya 12-Channel Smart Switch.

Figure 2: PCB dimensions in millimeters.

4. Setup

4.1 Pre-installation Checks

  • Ensure your smartphone or tablet is connected to a 2.4GHz WiFi network. 5GHz WiFi is not supported.
  • If using the Zigbee version, a Zigbee gateway is required and must be set up in the Tuya Smart App.
  • For Android devices, the operating system must be version 4.0 or above.
  • Ensure Bluetooth is enabled on your mobile phone.
  • If your wireless router has MAC address filtering enabled, please disable it in the router's settings before proceeding.

4.2 App Installation

  1. Search for "Tuya Smart" in your device's app store (Apple App Store or Google Play Store).
  2. Download and install the "Tuya Smart" app. You may also see "Smart Life" which is compatible; choose one, no need to install both.
  3. If prompted for permission requests during installation, please grant them.
  4. Register your account and log in to the Tuya Smart App.
Screenshot showing Tuya Smart and Smart Life app icons.

Figure 3: Tuya Smart and Smart Life app icons.

4.3 Wiring

  • Connect the wiring correctly according to the instructions. Ensure there is NO LIVE INSTALLATION. Always disconnect power before wiring.
  • After wiring is complete, power on the device. The default power-on state for the device is OFF, but this can be changed within the Tuya Smart App.

4.4 Adding Device to Mobile App

  1. Reset the device: If the network indicator light is already flashing rapidly (approximately twice per second) after power-on, you can skip this step. Otherwise, press and hold the reset button on the module for about 10 seconds. Release the button when the network indicator light begins to flash rapidly (2-4 times per second).
  2. Open the Tuya Smart App, tap the "+" icon to add a device, then select "Auto-discovery". Wait a few seconds for the app to find the device, then select "Next" when prompted.
  3. Select your 2.4GHz WiFi network and enter the password. (For Zigbee versions, first add your Zigbee gateway in the Tuya App, then search for and add Zigbee module sub-devices through the gateway's control interface.)
  4. Once successfully added, you can name the device to complete the process.
  5. When the network indicator light on the device is solid (on for a long time), remote control via the app is enabled.
  6. If the WiFi network is disconnected, the WiFi model product switch will automatically switch to Bluetooth control via your mobile phone.

5. Operating Instructions

5.1 Basic Control via App

  • On the Tuya Smart App homepage, tap the switch icon for the device to turn it on or off.
  • If the physical switch is controlled manually, the app will display the current ON/OFF status of the device in real-time.
Screenshot of the Tuya Smart App interface showing 12 switches, with switches 10 and 11 highlighted in red, indicating they are open.

Figure 4: App interface showing channel status. Red indicates an open channel.

5.2 Mobile App Function Settings

To access advanced settings, tap the switch name in the app to enter the function settings page.

Interlock Settings

Interlock mode prevents multiple channels from being active simultaneously or defines specific channel relationships. Input values determine the interlock behavior:

  • Input 2 above, 2 below: Channels 1 and 2 are interlocked.
  • Input 3 above, 3 below: Channels 1, 2, and 3 are interlocked.
  • Input 10 above, 10 below: Channels 1 through 10 are interlocked.
  • Input 4 above, 2 below: Channels 1-2 and 3-4 are interlocked.
  • Input 8 above, 2 below: Channels 1-2, 3-4, 5-6, and 7-8 are interlocked.
  • Input 10 above, 5 below: Channels 1-5 and 6-10 are interlocked.
  • Input 0 above, 0 below: No interlock is set.

Inching (Jog) Settings

Inching mode allows a channel to turn on for a set duration and then automatically turn off.

  • Channel number input (e.g., 1): Displays the current inching time for that channel. This time can be changed (e.g., 500 milliseconds).
  • Inching time input 0: The specified channel will not operate in inching mode.
  • Description: Inching time range is 1 to 999,999,999 milliseconds.

Switch Exclusive Setting (for models with physical switch input)

This setting defines how the module responds to physical switch inputs.

  • Channel number input (e.g., 1): Displays the current setting value for that channel.
  • Input 1 below: The channel cannot be controlled via the mobile phone; its status is solely determined by the physical switch input.
  • Input 2 below: A high-level switch input triggers the channel to flip its state.
  • Input 3 below: A low-level switch input triggers the channel to flip its state (applicable to products supporting low-level triggers).

Power-on Settings

These settings determine the state of the channels when the module is powered on.

  • Channel number input (e.g., 1): Displays the current setting value for that channel.
  • Input 1 below: The channel will automatically turn ON upon power-on.
  • Input 2 below: The channel will turn OFF upon power-on.
  • Input 3 below: The channel will resume its last known state before power-off.
  • Input 4 below: The channel will be forcibly turned ON upon power-on, and the mobile phone app will not be able to control this channel.

Delayed Opening/Closing (some products may not support this)

This feature allows a delay before a channel opens or closes.

  • Input 1 above: Displays the current delay setting for channel 1.
  • Input 3000 below: The channel will not open/close immediately when commanded, but will do so automatically after 3000 milliseconds (3 seconds).
Screenshot of the Tuya Smart App interface showing general instructions for interlock, inching, switch exclusive, and power-on settings.

Figure 5: General instructions for various settings within the Tuya Smart App.

5.3 Special Function: 106 Running Light Action

This function allows you to quickly set a running light action for channels when fully turned on and off.

  • Navigate to the settings page in the app.
  • Click on the product serial number value.
  • Select all and delete existing values.
  • Enter 500 to set an interval of 500 milliseconds between actions.
  • Finally, enter 106 to confirm completion. (Example: 500106)
  • To turn off this function, enter 0 for the interval (0 milliseconds).

5.4 Remote Control Pairing/Deleting (433MHz RF)

The remote control pairing/deletion method uses a standard frequency RF433MHz learning remote control with a 1527 series chip.

Pairing

  1. Quickly press the module's setting button 5 times. Relay 1 will jog, and its LED will flash.
  2. Bring the remote control close to the module. Press and hold button 1 on the remote control. After successful learning, the relay will automatically jump to the second channel.
  3. Continue by pressing and holding button 2 on the remote control to complete learning for the second channel, and so on for subsequent channels.
  4. If you wish to skip a specific relay during the learning process, simply click the module's setting key, and it will advance to the next relay. Then, continue the pairing operation.

Deletion

  • To clear all remote control settings, press and hold the module's setting button for 10 seconds. The module will then return to its factory settings for remote control.
Text instructions for remote control pairing and deletion methods.

Figure 6: Remote control pairing and deletion instructions.

6. Maintenance

Restore Factory Settings

  • To restore the module to its factory settings, press and hold the setting button for more than 10 seconds. Release your hand once the indicator light flashes rapidly.
  • After a factory reset, you will need to re-add the device to your mobile app and reconfigure all settings.

7. Troubleshooting

  • Device not connecting to WiFi: Ensure your router is broadcasting a 2.4GHz network, you have entered the correct WiFi password, Bluetooth is enabled on your phone, and MAC filtering is disabled on your router.
  • Remote control not responding: Verify that the remote control has been correctly paired following the instructions in Section 5.4. Check the remote control's battery if applicable.
  • App control issues: Check your mobile device's internet connection. Ensure the smart switch module is powered on and its network indicator light is solid. Verify that the Tuya Smart App has the necessary permissions.
  • Incorrect channel status displayed in app: Review the "Power-on Settings" in the app (Section 5.2) to ensure they match your desired behavior. Note that for normally closed terminals, if the relay is not energized, it might display as 'red' (open) in the app.

8. User Tips

  • Power Supply Flexibility: The module supports multiple power input options (DC7V~27V, AC85-250V, or Type-C 5V). Choose the appropriate power supply based on your application and ensure it matches the module's requirements.
  • Understanding Power Draw: The module has a maximum power rating of 220V/2200W, meaning it can handle up to 10A at 220V. Each individual relay is rated for 10A at 277VAC or 12A at 125VAC. Ensure the connected load does not exceed these limits.
  • Zigbee Gateway for Zigbee Models: Remember that the Zigbee version of this switch requires a separate Zigbee gateway to function within the Tuya ecosystem.

9. Warranty and Support

For warranty information and technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.