Trimble GFX-750 XCN-1050 GFX750

Contents

Trimble GFX-750 / XCN-1050 LCD Display Panel with Touch Screen User Manual

Model: GFX-750, XCN-1050, GFX750

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your new original 10.1-inch LCD Display Panel with Touch Screen, compatible with Trimble GFX-750, XCN-1050, and GFX750 monitors. Please read this manual thoroughly before attempting any installation or operation to ensure safe and effective use.

Front view of the Trimble GFX-750 XCN-1050 GFX750 LCD Display Panel with touch screen in use.
Figure 1: Front view of the LCD Display Panel with touch screen in use.

2. Setup and Installation

This display panel is designed for specific Trimble models. Ensure compatibility before proceeding. Professional installation is recommended due to the delicate nature of electronic components.

2.1 Pre-Installation Checklist

  • Verify the model number of your existing monitor (GFX-750, XCN-1050, GFX750).
  • Ensure you have the necessary tools for disassembly and reassembly.
  • Work in a clean, static-free environment.
  • Disconnect all power sources from the device before starting.

2.2 Installation Steps (General Guidance)

  1. Carefully remove the old display panel from your Trimble monitor. Refer to your specific Trimble monitor's service manual for detailed disassembly instructions.
  2. Inspect the new LCD display panel for any visible damage before installation.
  3. Connect the ribbon cable(s) from the new display panel to the corresponding connectors on the monitor's main board. Ensure connections are secure and properly seated.
  4. Mount the new display panel into the monitor housing.
  5. Before fully reassembling, perform an initial power-on test to verify display functionality and touch response.
  6. Once verified, complete the reassembly of your Trimble monitor.
Rear view of the LCD display panel showing connection points and labels.
Figure 2: Rear view of the LCD Display Panel, highlighting connection points.
Close-up of the ribbon cable connector on the back of the LCD display panel.
Figure 3: Close-up of the ribbon cable connector.

2.3 Initial Testing

After connecting the display, power on the device to check for proper image display and touch functionality. A video demonstrating the display test procedure is available:

Video 1: Display panel color test and connection overview.

3. Operation

The LCD display panel functions as a direct replacement for the original screen in your Trimble GFX-750, XCN-1050, or GFX750 monitor. It provides visual output and touch input capabilities identical to the original component.

  • Display Functionality: The panel will display information as provided by your Trimble monitor's system.
  • Touch Screen: Use your finger or a compatible stylus for interactive input, navigating menus, and operating applications on your Trimble device.

For specific operational details regarding your Trimble GFX-750, XCN-1050, or GFX750 monitor, please refer to the original user manual provided with your Trimble device.

4. Maintenance and Care

Proper maintenance ensures the longevity and optimal performance of your LCD display panel.

  • Cleaning the Screen:
    • Gently wipe the screen with a soft, lint-free cloth.
    • For stubborn smudges, lightly dampen the cloth with water or a screen-specific cleaning solution. Do not spray liquid directly onto the screen.
    • Avoid using harsh chemicals, abrasive cleaners, or alcohol-based solutions, as these can damage the screen coating.
  • Protection:
    • Avoid applying excessive pressure to the screen.
    • Protect the screen from sharp objects to prevent scratches.
    • Keep the device away from extreme temperatures and direct sunlight for prolonged periods.

5. Troubleshooting

If you encounter issues with your display panel, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No image on screenLoose or incorrect cable connection; power issue; faulty panel.
  • Check all ribbon cable connections to ensure they are secure.
  • Verify the monitor is receiving power.
  • If issues persist after checking connections, contact support.
Touch screen unresponsiveLoose touch digitizer cable; software issue; faulty touch layer.
  • Ensure the touch digitizer cable is properly connected.
  • Restart the Trimble device.
  • If the problem continues, contact support.
Distorted or incorrect colorsLoose display cable; graphics driver issue (less likely for a panel replacement); faulty panel.
  • Check display cable connections.
  • Perform a display test (refer to Section 2.3).
  • Contact support if the issue persists.

If the product is defective or not working after installation, please contact us immediately for assistance. Do not attempt further repairs yourself if you are unsure.

6. Specifications

FeatureDetail
Product TypeLCD Display Panel with Touch Screen Glass
CompatibilityTrimble GFX-750, XCN-1050, GFX750
Screen Size10.1 inches
ConditionNew Original (or Used in great working condition if original is discontinued)
OriginMainland China
High-concerned chemicalNone
Package Weight0.9 kg
Package Dimensions (L x W x H)37 cm x 26 cm x 6 cm

A user manual in PDF format is also available for additional guidance. Please refer to the seller's product page for the direct link to the PDF document.

7. User Tips

  • Compatibility Check: Always double-check the compatibility with your specific Trimble GFX-750, XCN-1050, or GFX750 model before ordering. If unsure, contact the seller for technical advice.
  • Pre-Shipment Testing: The product undergoes 100% testing with real equipment before shipment, ensuring functionality upon arrival.
  • Inspect Rear Connections: Before installation, familiarize yourself with the rear attachments and connectors of the screen. This helps in proper alignment and secure connection during installation.
  • Bulk Orders: For orders of more than 10 pieces, contact the seller for potential discounts.

8. Warranty and Support

8.1 Warranty Information

  • This product comes with a 1-year warranty.
  • A 30-day money-back or replacement policy is offered if the product is defective or not working upon receipt.
  • All returned items and accessories must be in their original, unused condition.
  • Each item is affixed with a warranty label; please do not remove or tear this label, as it may void the warranty.

8.2 Technical Support

For technical advice, installation guidance, or troubleshooting assistance, please contact the seller directly. They can provide support and help resolve any issues you may encounter.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.