1. Introduction
The BRZHIFI DC300 is a high-fidelity audio Digital-to-Analog Converter (DAC) designed for discerning audiophiles. It features a dual-core ES9038PRO or ES9039PRO decoding scheme, offering exceptional sound quality with low signal-to-noise ratio and minimal harmonic distortion. The unit incorporates premium components, including MUSES op-amps, femtosecond clock crystal oscillators, and fully sealed low-leakage magnetic transformers, all housed in a high-end CNC chassis with a 2.08-inch OLED display.
2. Product Overview
The DC300 DAC is available in two main versions: ES9038PRO HIEND and ES9039PRO HIFI. Both versions are designed for superior audio performance.




3. Setup Instructions
Follow these steps to set up your BRZHIFI DC300 DAC:
- Unpacking: Carefully remove the DAC and all accessories from the packaging. Ensure all components are present, including the remote control and power cable.
- Power Connection: Connect the provided AC power cable to the AC 220V input on the rear panel of the DAC. Ensure the voltage matches your local power supply (AC 110V versions are available upon customization).
- Input Source Connection:
- USB Input: Connect your computer (Windows, Vista, Linux, MacOSX, Daphile) or mobile phone (with OTG support) to the USB input port. Note: USB input does not support USB flash drives or hard disks. Windows may require a driver.
- Bluetooth Input: Attach the Bluetooth antenna to the designated connector on the rear panel. The DAC supports Bluetooth 5.0 with AAC/SBC/APTX/APTX-LL/APTXHD/LDAC codecs.
- Coaxial/Optical Input: Connect your digital audio source (e.g., DVD, set-top box, Smart TV) to the COAX or OPTICAL input ports.
- Output Connection: Connect the DAC to your amplifier, active speakers, or headphones using the appropriate output interface:
- Balanced Output: Use XLR cables for balanced analog signal output to a compatible amplifier. The balanced output standard is European standard (1 ground, 2 positive, 3 negative).
- Single-ended Output: Use RCA cables for single-ended analog signal output to a compatible amplifier or active speakers.
- 3.5mm Analog Output: For headphone or other compatible devices.
- Power On: Press the Power switch on the front panel to turn on the DAC.


4. Operating Instructions
The DC300 DAC is designed for intuitive operation via its front panel controls and the included remote control.
4.1 Front Panel Controls
- Power Switch: Press to turn the unit on/off. Long press the input switch (UP button) to switch the digital filter mode.
- OLED Display: Shows current input, sampling rate, volume level, and filter mode.
- UP Button: Increases volume. Also functions as input selection (short press) or digital filter mode switch (long press).
- DOWN Button: Decreases volume.
- MENU Button: Used for menu navigation or settings adjustment.
4.2 Remote Control
The exquisite remote control provides convenient access to all functions.

- Input Selection: Cycle through available input sources (USB, Bluetooth, Coaxial, Optical).
- Volume Plus/Reduction: Adjust the output volume.
- Mute: Mute/unmute the audio output.
- Filter Selection: Change digital filter modes for different sound characteristics.
4.3 Bluetooth Pairing
- Ensure the Bluetooth antenna is connected to the DAC.
- Switch the DAC input to Bluetooth mode. The OLED display will indicate Bluetooth status.
- On your mobile device, search for available Bluetooth devices and select "BRZHIFI DC300" (or similar name).
- Once paired, audio from your device will be streamed to the DAC.
5. Maintenance
To ensure the longevity and optimal performance of your BRZHIFI DC300 DAC, follow these maintenance guidelines:
- Cleaning: Use a soft, dry cloth to clean the exterior of the unit. Avoid using liquid cleaners, aerosols, or abrasive materials, as they may damage the finish or internal components.
- Ventilation: Ensure adequate ventilation around the unit. Do not block the ventilation holes on the top and sides. Avoid placing the DAC in enclosed spaces or on soft surfaces that may impede airflow.
- Environment: Keep the DAC away from direct sunlight, heat sources, excessive dust, moisture, and strong electromagnetic fields.
- Power Off: When not in use for extended periods, it is recommended to power off the unit and disconnect it from the mains supply.
6. Troubleshooting
If you encounter any issues with your DC300 DAC, refer to the following common troubleshooting steps:
- No Power:
- Check if the power cable is securely connected to both the DAC and the power outlet.
- Ensure the power outlet is functional.
- Verify the power switch on the front panel is pressed.
- No Sound Output:
- Confirm the correct input source is selected on the DAC.
- Check all audio cables (USB, Coaxial, Optical, RCA, XLR, 3.5mm) for secure connections.
- Ensure the volume level on the DAC and your connected amplifier/speakers is not set to minimum or muted.
- If using USB, ensure the necessary drivers are installed on your computer (for Windows).
- If using Bluetooth, ensure the device is properly paired and connected.
- Distorted Sound:
- Check the quality of your input audio source.
- Ensure all cables are in good condition and properly connected.
- Reduce the volume level on the DAC or connected amplifier to prevent clipping.
- Remote Control Not Responding:
- Check the batteries in the remote control and replace if necessary.
- Ensure there are no obstructions between the remote and the DAC's infrared receiver.
7. Specifications

| Feature | Specification |
|---|---|
| Model | DC300 |
| Decoding Scheme | ES9038PRO Dual-core / ES9039PRO Dual-core |
| Product Dimensions (W x H x D) | 318mm x 62mm x 248mm |
| Product Weight | 3.65 KG |
| Digital Input | USB / Mobile Phone OTG, Bluetooth, Coaxial (COAX), Optical Fiber (OPT) |
| Output Interface | Single-ended Analog Signal (RCA), Balanced Analog Signal (XLR), 3.5mm Analog Signal |
| USB Input Support | PCM44.1K - 384K24/32bit, DSD64 - DSD512 |
| OS Compatibility (USB) | Windows/Vista/Linux/MacOSX/Daphile (Windows requires driver) |
| Coaxial/Optical Input Support | PCM44.1K - 192K16 - 24bit (COAX input supports DOP64) |
| Bluetooth Input Codecs | AAC/SBC/APTX/APTX-LL/APTXHD/LDAC |
| Dynamic Range | ≥ 120dB |
| Distortion Rate | 0.0005% |
| Frequency Response | 20Hz-20KHz +/-0.08dB |
| Line Output (RCA) | Single-ended 2.3Vrms |
| Line Output (XLR) | Balanced 5.6Vrms |
| Rated Power | 25W (AC110 ~ AC240V, AC110V customizable) |
| Channels | 2 (2.0) |
| Maximum Power Per Channel | NO POWER (DAC only, not an amplifier) |
8. User Tips
- For optimal sound quality, use high-quality audio cables for all connections.
- Experiment with different digital filter modes to find the sound signature that best suits your preferences and audio content.
- When connecting to a computer, ensure your audio playback software is configured to output audio directly to the DAC (e.g., WASAPI or ASIO for Windows) to bypass the operating system's audio mixer.
- Consider using a dedicated power conditioner or surge protector to protect your DAC from power fluctuations.
9. Additional Information
9.1 Internal Components and Design
The DC300 DAC features a meticulously designed internal layout with high-quality components to achieve its superior audio performance. Key features include:
- Dual ESS Flagship Chips: Two ES9038PRO or ES9039PRO chips are used for decoding, one for each of the left and right channels, ensuring completely independent decoding, independent power supply, and independent grounding. This design minimizes signal-to-noise ratio and harmonic distortion.
- MUSES Op-Amps: Utilizes MUSES03 op-amps (or OPA1612/OPA604/OPA1611 depending on version) for output, known for their excellent sound field, positioning, and air sense.
- Femtosecond Clock Crystal Oscillator: Incorporates a 100MHz femtosecond crystal or active low-noise temperature-compensated crystal oscillator (Crystek CVHD-950) for precise timing and reduced jitter.
- Power Supply: Equipped with two fully sealed low-leakage magnetic transformers for stable and clean power delivery to both digital and analog circuits, preventing interference.
- PCB: Built on a 4-layer military sunken gold PCB for a robust and high-performance foundation.







9.2 Product Demonstration Video
10. Warranty and Support
For any technical assistance, warranty claims, or product inquiries, please contact your retailer or the manufacturer's customer support. Keep your purchase receipt as proof of purchase for warranty purposes.