Introduction
The Nasedal R500 LVLP (Low Volume Low Pressure) Spray Gun is designed for efficient and precise application of various coatings, including water-based and medium-viscosity paints. Its advanced LVLP technology ensures a smooth finish with minimal overspray, making it ideal for automotive refinishing, furniture painting, model making, and other industrial or DIY projects. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your spray gun.
Package Contents
Please check the package to ensure all items are present:
- R500 Spray Gun (1 unit)
- 600cc Paint Cup (1 unit)
- Mini Filter (1 unit)
- Quick Release Connector (1 unit)
- Cleaning Brush (1 unit)
- Wrench (1 unit)
- Air Regulator Gauge & Oil-Water Trap Filter & Quick Release Connector (1 unit, optional)

Specifications
| Attribute | Value |
|---|---|
| Model | R500 |
| Type | LVLP Spray Gun |
| Feed Type | Gravity |
| Standard Nozzle | 1.3mm |
| Operating Pressure | 2.0-3.5 bar |
| Pattern Width | 180-280mm |
| Air Consumption | 3.0-3.9cfm |
| Paint Consumption | 130-170 ml/min |
| Paint Cup Capacity | 600cc |
| Paint Ratio | >= 65% |
| Material | Die-casting Aluminum body, Stainless Steel Nozzle & Needle, Plastic Cup, Copper Air Cap |
| Application | Household Tool Set, Paint & Decorating, Automotive, Car, Home, Furniture Painting Projects |
| Dimensions (Gun) | Approx. 16cm (6.3in) x 18cm (7.09in) |
| Dimensions (Cup) | Approx. 10cm (3.94in) x 15.7cm (6.18in) |


Setup
- Unpack and Inspect: Carefully remove all components from the packaging. Inspect for any damage.
- Assemble the Paint Cup: Securely attach the 600cc plastic paint cup to the top of the spray gun. Ensure it is tightly sealed to prevent leaks.
- Connect Air Supply: Attach the quick release connector to the air inlet at the bottom of the spray gun handle. Connect your air compressor hose to this quick release connector.
- Install Air Regulator (Optional): If using the optional Air Regulator Gauge & Oil-Water Trap Filter, connect it between your air compressor hose and the spray gun's quick release connector. This accessory helps prevent water contamination and allows for precise air pressure adjustment.
- Prepare Paint: Mix your paint according to the manufacturer's instructions. Ensure it is strained to remove any particles that could clog the nozzle. Fill the 600cc paint cup with the prepared paint.
- Adjust Nozzle and Air Cap: The spray gun comes with a 1.3mm standard nozzle. Ensure the stainless steel nozzle and copper air cap are securely in place. The air cap is 360-degree adjustable for spray pattern orientation.

Operating Instructions
The Nasedal R500 features three adjustable valve knobs for precise control over your painting process:
- Air Flow Adjust Valve: Located at the bottom of the handle, this knob controls the overall air volume.
- Paint Flow Control Knob: Located at the rear of the gun, this knob adjusts the amount of paint released.
- Spray Width Control Knob: Located on the side, this knob modifies the width of the spray pattern.
Trigger Functionality:
- Trigger 1 (Partial Press): For blowing air only.
- Trigger 2 (Full Press): For spraying paint.
General Operation:
- Ensure your work area is well-ventilated and wear appropriate personal protective equipment (PPE), including a respirator, safety glasses, and gloves.
- Set your air compressor to the recommended operating pressure of 2.0-3.5 bar.
- Adjust the air volume, paint flow, and spray pattern using the respective knobs. It is recommended to test the spray pattern on a scrap piece of material before applying to your final surface.
- Maintain a consistent distance from the surface and move the gun in smooth, even strokes.
- The LVLP technology ensures fine atomization with minimum overspray, leading to a smooth finish and reduced paint waste.


Maintenance
Proper cleaning and maintenance are crucial for the longevity and optimal performance of your spray gun.
- Immediate Cleaning: After each use, immediately empty any remaining paint from the cup. Clean the cup thoroughly with an appropriate solvent or water, depending on the paint type.
- Flush the Gun: Fill the paint cup with clean solvent or water and spray it through the gun until the liquid runs clear.
- Disassemble and Clean Nozzle/Air Cap: Use the provided wrench to carefully remove the air cap and nozzle. Use the cleaning brush and mini filter to clean all paint passages, the nozzle, and the air cap. Pay close attention to the 9 holes in the air cap to ensure they are free of clogs.
- Clean Needle: Gently clean the paint needle. Avoid bending or damaging the needle.
- Lubrication: Apply a small amount of spray gun lubricant to moving parts and threads as needed.
- Storage: Store the clean and dry spray gun in a safe place, away from dust and extreme temperatures.

Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven Spray Pattern | Clogged air cap holes or nozzle; incorrect pressure settings. | Clean air cap and nozzle thoroughly. Adjust air pressure and spray width knob. |
| Paint Spitting/Pulsating | Insufficient paint in cup; paint too thick; air leak; clogged fluid tip. | Refill paint cup. Thin paint as per manufacturer. Check connections for leaks. Clean fluid tip. |
| No Paint Flow | Clogged nozzle/fluid tip; paint too thick; air cap not aligned; needle not retracting. | Clean nozzle and fluid tip. Thin paint. Ensure air cap is correctly oriented. Check needle movement. |
| Excessive Overspray | Too much air pressure; gun too far from surface; paint too thin. | Reduce air pressure. Move gun closer to surface. Thicken paint slightly. |
| Air Leakage | Loose connections; damaged O-rings/seals. | Tighten all connections. Inspect and replace damaged O-rings/seals. |
User Tips
- Read the Manual: Always read the entire instruction manual before first use to familiarize yourself with the product's features and safety guidelines.
- Test First: Before painting your main project, always test the spray pattern and paint consistency on a scrap piece of material. This allows you to fine-tune settings and avoid mistakes.
- Proper Ventilation: Always work in a well-ventilated area and use appropriate respiratory protection to avoid inhaling paint fumes.
- Clean Immediately: The most common cause of spray gun issues is dried paint. Clean your gun immediately after each use to prevent clogs and ensure smooth operation for next time.
- Check Product Options: When purchasing or replacing parts, carefully review the product options and descriptions to ensure you select the correct model or accessories, as different configurations may have varying prices and included components.
Warranty and Support
For warranty information, technical support, or replacement parts, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.