PowMr POW-48140A

Contents

PowMr 140A 48V MPPT Solar Charge Controller User Manual

Model: POW-48140A

Brand: PowMr

1. Introduction

1.1 Purpose

This manual describes the assembly, installation, operation, and troubleshooting of this unit. Please read this manual carefully before installations and operations. Keep this manual for future reference.

1.2 Scope

This manual provides safety and installation guidelines as well as information on tools and wiring.

1.3 Features

  • Configurable battery charging current based on applications via LCD setting.
  • Over temperature protection.
  • Smart battery charger design for optimized battery performance.
  • Cold start function.

1.4 Basic System Architecture

The following illustration shows the basic application for this solar charge controller.

Diagram of Hybrid Power System showing solar panels connected to controller and then to battery.
Figure 1: Hybrid Power System

1.5 Product Overview

The product features an LCD display, charging and fault indicators, and function buttons for user interaction. The unit includes PV input, battery input, and a ground connection.

Product overview diagram with numbered components: LCD display, charging indicator, fault indicator, function buttons, PV input, ground connection, battery input, and anti-dust kit.
Product Overview Diagram
No.Component
1LCD display
2Charging indicator
3Fault indicator
4Function buttons
5PV input
6Ground Connection
7Battery input
8Anti dust kit

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION - To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of lead acid batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION - Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this charger, please follow required spec to select appropriate cable size. It's very important to correctly operate this charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect DC terminals. Please refer to the INSTALLATION section of this manual for the details.
  10. One piece of 150A fuse is provided as over-current protection for the battery supply.
  11. NEVER cause DC input short circuited.
  12. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this charger back to local dealer or service center for maintenance.

3. Installation

3.1 Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the following items inside the package:

  • The unit x 1
  • User manual x 1

3.2 Preparation

Before connecting all wirings, please take off the bottom cover by removing two screws as shown below.

Diagram showing removal of the bottom port cover.
Removing the Port Cover

3.3 Mounting the Unit

Consider the following points before selecting where to install:

  1. Do not mount the charger on flammable construction materials.
  2. Mount on a solid surface.
  3. Install this charger at eye level in order to allow the LCD display to be read at all times.
  4. For proper air circulation to dissipate heat, allow a clearance of approx. 20 cm to the side and approx. 50 cm above and below the unit.
  5. The ambient temperature should be between 0°C and 55°C to ensure optimal operation.
  6. The recommended installation position is to be adhered to the wall vertically.
  7. Be sure to keep other objects and surfaces to guarantee sufficient heat dissipation and to have enough space for removing wires.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Install the unit by screwing two screws. It's recommended to use M6 screws.

Diagram showing mounting holes for the controller.
Mounting Holes

3.4 Battery Connection

For safety and efficient operation, use appropriate cables and ensure correct polarity.

ModelWire SizeCable(mm²)Torque value (max)
48V/140A1 x 2AWG252 Nm

CAUTION:

  • For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and charger. Please refer to typical amperage in the table above as required fuse or breaker size.

WARNING:

  • All wiring must be performed by qualified personnel.
  • It's very important for system safety and efficient operation to use appropriate cable for battery connection. To reduce risk of injury, please use the proper recommended cable.

Please follow these steps to implement battery connection:

  1. Remove insulation sleeve 18 mm for positive and negative conductors.
  2. Suggest to put bootlace ferrules on the end of positive and negative wires with a proper crimping tool.
  3. Connect all battery packs as shown in the diagram below.
  4. Insert the battery wires flatly into battery connectors of the charger and make sure the bolts are tightened with a torque of 2 Nm in a clockwise direction. Ensure polarity at both the battery and the charger is correctly connected and conductors are tightly screwed into the battery terminals.

Recommended tool: #2 Pozi Screwdriver

System installation diagram showing connections for battery, inverter, and solar panels.
Battery and System Wiring Diagram

WARNING:

  • Installation must be performed with care due to high battery voltage in series.

CAUTION:

  • Before making the final DC connection or closing the DC breaker/disconnector, be sure positive (+) must be connected to positive (+) and negative (-) must be connected to negative.

3.5 PV Connection

For safety and efficient operation, use appropriate cables for PV module connection.

ModelWire SizeCable(mm²)Torque value (max)
48V/140A1 x 12AWG41.2 Nm

CAUTION:

  • Before connecting to PV modules, please install separately a DC circuit breaker between the charger and PV modules.

WARNING:

  • It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size.

PV Module Selection:

When selecting proper PV modules, please be sure to consider the following parameters:

  1. Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the charger (500Vdc).
  2. Open circuit Voltage (Voc) of PV modules should be higher than the min. battery voltage.
MODEL48V/140A
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range60Vdc~500Vdc

For example, taking a 250Wp PV module, the recommended module configurations are listed below:

Solar Panel Spec. (reference)SOLAR INPUT (Min in serial: 6 pcs, max. in serial: 13 pcs)Q'ty of panelsTotal input power
- 250Wp
- Vmp: 30.1Vdc
- Imp: 8.3A
- Voc: 37.7Vdc
- Isc: 8.4A
- Cells: 60
6 pcs in serial6 pcs1500W
8 pcs in serial8 pcs2000W
12 pcs in serial12 pcs3000W
13 pcs in serial13 pcs3250W
8 pieces in serial and 2 sets in parallel16 pcs4000W
10 pieces in serial and 2 sets in parallel20 pcs5000W
12 pieces in serial and 2 sets in parallel24 pcs6500W

PV Module Wire Connection:

Please follow these steps to implement PV module connection:

  1. Remove insulation sleeve 10 mm for positive and negative conductors.
  2. Suggest to put bootlace ferrules on the end of positive and negative wires with a proper crimping tool.
  3. Check correct polarity of wire connection from PV modules and PV input connectors. Then, connect the positive pole (+) of the connection wire to the positive pole (+) of the PV input connector. Connect the negative pole (-) of the connection wire to the negative pole (-) of the PV input connector.

Recommended tool: 4mm blade screwdriver

3.6 Final Assembly

After connecting all wirings, please put the bottom cover back by screwing two screws.

Video: POW-48140A Solar Charge Controller Wiring Guide. This video demonstrates the step-by-step process of mounting the controller, connecting the battery, and connecting the PV array.

4. Operation

4.1 Operation and Display Panel

The operation and display panel is on the front of the charger. It includes two indicators, four function keys, and an LCD display, indicating the operating status and PV power information.

Large LCD screen display showing PV input and battery voltage.
LCD Display and Function Keys

LED Indicator

LED IndicatorMessages
CHG (Green)Solid On: Battery is fully charged
Flashing: Battery is charging.
FAULT (Red)Solid On: Fault occurs in the charger
Flashing: Warning condition occurs in the charger

Function Keys

Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

4.2 LCD Setting

After pressing and holding the ENTER button for 3 seconds, the unit will enter setting mode. Press the "DOWN" button to select setting programs. Then, press the "ENTER" button to confirm the selection or press the "ENTER" button a second time to exit.

Setting Programs:

No.DescriptionSelectable option
00Exit setting modeEscape (default): 00 GOE (One-button restore setting options)
00 GOK
02Maximum charging current60A (default): 02 60A
Setting range is 10~140A, increment of each click is 10A.
05Battery typeAGM: 05 AGM
Flooded: 05 FLD
USE (User-Defined): 05 USE (If "User-Defined" is selected, battery charge voltage can be set up in program 26 and 27.)
07Auto restart when over temperature occursRestart disable (default): 07 dIS
Restart enable: 07 ENA
26Bulk charging voltage (C.V voltage)48V default setting: 56.4V
If self-defined is selected in program 05, this program can be set up. Setting range is from 48.0V to 59.0V for 48V model. Increment of each click is 0.1V.
27Floating charging voltage48V default setting: 54.0V
If self-defined is selected in program 05, this program can be set up. Setting range is from 48.0V to 59.0V for 48V model. Increment of each click is 0.1V.
30Battery equalizationBattery equalization: 30 ENA
Battery equalization disable (default): 30 dIS
If "Flooded" or "User-Defined" is selected in program 05, this program can be set up.
31Battery equalization voltage48V default setting: 58.4V
Setting range is from 48.0V to 59.0V for 48V model. Increment of each click is 0.1V.
33Battery equalized time60min (default): 33 60
Setting range is from 5min to 900min. Increment of each click is 5min.
34Battery equalized timeout120min (default): 34 120
Setting range is from 5min to 900min. Increment of each click is 5min.
35Equalization interval30days (default): 35 30d
Setting range is from 0 to 90 days. Increment of each click is 1 day.
36Equalization activated immediatelyEnable: 36 ENA
Disable (default): 36 dIS
If equalization function is enabled in program 30, this program can be set up. If "Enable" is selected, it activates battery equalization immediately and the LCD main page will show "E9". If "Disable" is selected, it will cancel the equalization function until the next activated equalization time arrives based on program 35 setting. At this time, "E9" will not be shown in the LCD main page.
81Year set00-99
82Month set01-12
83Day set01-31
84Hour set00-24
85Minute set00-60
86Clean EnergyENABLE / DISABLE

4.3 Display

The LCD display information will be switched in turns by pressing the "UP" or "DOWN" key. The selectable information is switched in the following order: PV voltage, charging current, charging power, battery voltage, and main CPU Version.

Selectable InformationStatusLCD Display Example
Version numberStand byU1 70 01
ChargingU1 70 01
PV voltageStand byINPUT 3V, BATT 44.2V
ChargingINPUT 389V, BATT 53.9V
PV currentStand byINPUT 0A, BATT 44.2V
ChargingINPUT 2.9A, BATT 53.9V
PV temperature/PV powerStand byTEMP 25°C, PV 0W
ChargingTEMP 26°C, PV 1.20kW
Charge current/Battery voltageStand byBATT 0A, BATT 44.2V
ChargingBATT 24.8A, BATT 53.9V
Charge powerStand byBATT 23W, BATT 44.2V
ChargingBATT 1.34kW, BATT 53.9V
Daily power generationStand by1.59kWh, DAY 889
Charging1.59kWh, DAY 889
Monthly power generationStand by1.59kWh, MON 000
Charging1.59kWh, MON 000
Gross generationStand by1.59kWh, EOL
Charging1.59kWh, EOL
DateStand by23 11 17
Charging23 11 17

4.4 Fault Reference Code

Fault CodeFault EventIcon on
01Fan is locked when charger is off.01 ERROR
02Over temperature02 ERROR
03Battery voltage is too high03 ERROR
08Bus voltage is too high08 ERROR
09Bus soft start failed09 ERROR
51Over current or surge51 ERROR
52Bus voltage is too low52 ERROR
57Current sensor failed57 ERROR
59PV voltage is over limitation59 ERROR

4.5 Warning Indicator

Warning CodeWarning EventAudible AlarmIcon flashing
E9Battery equalizationNoneE9®
bPBattery is not connectedNonebP

5. Battery Equalization Description

Equalization function is added to the charge controller. It reverses the buildup of negative chemical effects like stratification, a condition where acid concentration is greater at the bottom of the battery than at the top. Equalization also helps to remove sulfate crystals that might have built up on the plates. If left unchecked, this condition, called sulfation, will reduce the overall capacity of the battery. Therefore, it's recommended to equalize the battery periodically.

5.1 How to Apply Equalization Function

You must enable the battery equalization function in monitoring LCD setting program 05 first. Then, you may apply this function in the device by either one of the following methods:

  1. Setting equalization interval in program 35.
  2. Active equalization immediately in program 36.

5.2 When to Equalize

In the float stage, when the setting equalization interval (battery equalization cycle) is reached, or equalization is active immediately, the controller will start to enter the Equalize stage.

Battery equalization charging stages graph (Bulk, Absorption, Float, Equalize).
Battery Equalization Charging Stages

5.3 Equalize Charging Time and Timeout

In the Equalize stage, the controller will supply power to charge the battery as much as possible until the battery voltage raises to the battery equalization voltage. The battery will remain in the Equalize stage until the setting battery equalized time is reached.

Battery equalization charging stages graph with timeout.
Battery Equalization with Charging Time

However, in the Equalize stage, when the equalized time is expired and the battery voltage doesn't rise to the battery equalization voltage point, the charge controller will extend the battery equalized time until the battery voltage achieves the battery equalization voltage. If the battery voltage is still lower than the battery equalization voltage when the battery equalized timeout setting is over, the charge controller will stop equalization and return to the float stage.

6. Clearance and Maintenance for Anti-Dust Kit

6.1 Overview

Every controller is already installed with an anti-dust kit from the factory. The controller will automatically detect this kit and activate an internal thermal sensor to adjust the internal temperature. This kit also keeps dust from your controller and increases product reliability in harsh environments.

6.2 Clearance and Maintenance Steps

  1. Step 1: Loosen the screw in a counterclockwise direction on the top of the controller.
  2. Diagram showing removal of the anti-dust kit.
    Removing the Anti-Dust Kit
  3. Step 2: The dustproof case can then be removed, and the air filter foam taken out.
  4. Step 3: Clean the air filter foam and dustproof case. After cleaning, re-assemble the dust-kit back to the controller.

NOTICE: The anti-dust kit should be cleaned from dust every one month.

7. Specifications

MPPT Solar Charging Mode

MODELPOW-48140A
Max. PV Array Power6500W
Nominal PV Voltage280Vdc
PV Array MPPT Voltage Range60Vdc~450Vdc
Max. PV Array Open Circuit Voltage500Vdc
Max Charging Current140Amp

Charging Curve

Charging Curve graph showing battery voltage and charging current over time.
Charging Curve
ParameterValue
Dimension435×310×180mm
Weight6.5kg

8. Troubleshooting

ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell)
2. Internal fuse tripped.
1. Contact repair center for replacing the fuse.
2. Re-charge battery.
3. Replace battery.
Red LED is on.Fault code 02Internal temperature of charger component is over 70°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Battery is over-charged.Return to repair center.
Fault code 03The battery voltage is too high.Check if spec and quantity of batteries are meet requirements.
Fault code 01Fan faultReplace the fan.
Fault code 52Bus voltage is too low.Restart the unit, if the error happens again, please return to repair center.

9. User Tips

  • Wiring Clarity: While the controller has internal separation between batteries and PV, it's crucial to ensure all external wiring for battery and PV connections are clearly separated and correctly installed to prevent issues.
  • Fan Noise: Be aware that the cooling fans may become noticeably louder when the charging current exceeds 40A, which is normal operation for heat dissipation.
  • Initial Setup: Although the controller offers configurable settings, it's recommended to review and adjust the battery charging current and type via the LCD settings during initial setup to match your specific battery system for optimal performance and longevity.
  • PDF Manual: For a detailed, printable version of the user manual, please refer to the official PDF document available at PowMr 140A 48V MPPT Solar Charge Controller User Manual (PDF).

10. Warranty and Support

For technical support, service, or warranty inquiries, please contact:

SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD
Tel/Fax: +86755-28219903
Email: support@powmr.com
Web: www.powmr.com
Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.