1. Product Overview
The LCTC Slim DIN Rail Solid State Relay Module is a compact and efficient solution for industrial control applications. These non-contact relays offer reliable switching for various loads, featuring a slim design that saves significant space on DIN rails. The modules are available in two main variants: SSR-41FDA (DC to AC) and SSR-41FDD (DC to DC), both designed for easy installation and maintenance.

Figure 1: LCTC Slim DIN Rail Solid State Relay Modules (10 pieces shown)
Key features include:
- Ultra-thin design (0.19 inches wide) for significant space saving (up to 70% for 10 modules).
- Non-contact switching for extended lifespan and reduced noise.
- Integrated LED indicator for status monitoring.
- Easy DIN rail installation with anti-detachment buckle for quick removal.
- Available in DC to AC (SSR-41FDA) and DC to DC (SSR-41FDD) control modes.
Video 1: Overview of LCTC Slim Solid State Relays, showcasing their design and form factor.
2. Specifications
The following table details the technical specifications for the SSR-41FDA and SSR-41FDD models:
| Feature | SSR-41FDA (DC to AC) | SSR-41FDD (DC to DC) |
|---|---|---|
| Model | SSR-41FDA | SSR-41FDD |
| Control Mode | DC to AC | DC to DC |
| Control Voltage | 3-32VDC | 3-32VDC |
| Load Voltage | 24-250VAC | 5-60VDC |
| Peak Current | 6A | 6A |
| Off State Time | ≤10mS | ≤10mS |
| Operating Current | 50mA-1A | 10mA-1.5A |
| Installation Method | Rail installation | Rail installation |
Dimensions (unit: inches):

Figure 2: Product dimensions (width 0.19in ultra-thin).
3. Installation
The LCTC Slim Solid State Relay Modules are designed for quick and convenient DIN rail installation.
- Mounting on DIN Rail: Align the module's base with a standard 1.33-inch DIN rail. Press firmly until it clicks into place.
- Space Saving: Due to their ultra-thin 0.19-inch width, these modules allow for significant space savings, enabling more components to be mounted on the same rail.
- Removal: To remove a module, use the anti-detachment buckle. Gently pry open the buckle, and the relay will pop up, allowing for easy removal without special tools.

Figure 3: Slim design and DIN rail installation. Ten modules save 70% space compared to standard relays.

Figure 4: Anti-detachment buckle for easy removal of the relay module.
4. Wiring Diagram
Proper wiring is essential for the safe and correct operation of the solid state relay modules. Refer to the specific diagrams below for your model.
4.1. SSR-41FDA (DC to AC) Wiring
This model controls an AC load using a DC control signal.

Figure 5: Wiring Diagram for SSR-41FDA (DC to AC). Control input A1- and A2+ (3-32VDC). Load connected to A1~ and A2~ (24-250VAC).
- Control Input: Connect the DC control signal (3-32VDC) to terminals A1- and A2+. Ensure correct polarity.
- Load Connection: Connect the AC power supply (24-250VAC) and the AC load to terminals A1~ and A2~.
4.2. SSR-41FDD (DC to DC) Wiring
This model controls a DC load using a DC control signal.

Figure 6: Wiring Diagram for SSR-41FDD (DC to DC). Control input A1- and A2+ (3-32VDC). Load connected to A1- and A2+ (5-60VDC).
- Control Input: Connect the DC control signal (3-32VDC) to terminals A1- and A2+. Ensure correct polarity.
- Load Connection: Connect the DC power supply (5-60VDC) and the DC load to terminals A1- and A2+. Ensure correct polarity for the load circuit.
Warning: Always ensure power is disconnected before performing any wiring to prevent electrical shock or damage to the device.
5. Operation
Once properly installed and wired, the LCTC Solid State Relay Module operates as follows:
- Power On: Apply the appropriate control voltage (3-32VDC) to the control terminals (A1-, A2+).
- Status Indicator: The integrated LED indicator will illuminate when the control voltage is applied, signifying that the relay is in the ON state and the load circuit is closed.
- Switching: The relay will switch the load circuit ON or OFF based on the presence or absence of the control voltage. The switching time is very fast, typically ≤10mS.
- Non-Contact Switching: As a solid state relay, it performs switching electronically without moving parts, offering high reliability, long life, and silent operation compared to mechanical relays.
6. Maintenance
LCTC Solid State Relay Modules are designed for minimal maintenance. However, regular checks can ensure optimal performance and longevity:
- Visual Inspection: Periodically inspect the modules for any signs of physical damage, discoloration, or loose connections.
- Cleanliness: Keep the modules and surrounding area free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
- Connection Integrity: Ensure all wiring connections are secure and free from corrosion. Loose connections can lead to overheating or intermittent operation.
- Environmental Conditions: Verify that the operating environment remains within the specified temperature and humidity ranges to prevent premature failure.
Caution: Always disconnect power to the control system and load before performing any maintenance or inspection.
7. Troubleshooting
If you encounter issues with your LCTC Solid State Relay Module, consider the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Relay not switching ON (LED off) | No control voltage or incorrect polarity. Control voltage too low. Faulty control circuit. | Check control voltage (3-32VDC) and polarity. Ensure control circuit is functioning correctly. |
| Relay not switching OFF (LED on, but load off) | Load circuit open. Incorrect load voltage. Overload condition. | Check load wiring and continuity. Verify load voltage matches relay specifications (24-250VAC for FDA, 5-60VDC for FDD). Ensure load current does not exceed 6A. |
| Relay remains ON even without control signal (LED off or on) | Internal relay failure. Leakage current (for AC loads). | Replace the relay. For AC loads, consider adding a snubber circuit or a load with higher impedance if leakage current is an issue. |
| Overheating | Excessive load current. Insufficient ventilation. Ambient temperature too high. | Reduce load current or use a relay with a higher current rating. Ensure adequate airflow around the modules. Operate within specified ambient temperature limits. |
8. User Tips
- Heat Sinking: For continuous operation at higher currents, especially close to the maximum 6A, consider using external heat sinks or ensuring good ventilation to prevent overheating and prolong relay life.
- Inductive Loads: When switching inductive loads (e.g., motors, solenoids), it is recommended to use external surge suppression (e.g., varistors for AC, diodes for DC) across the load to protect the relay from voltage spikes.
- Multiple Relays: When installing multiple relays on a DIN rail, ensure sufficient spacing if possible, especially in high-temperature environments, to aid in heat dissipation.
- LED Indicator: The built-in LED is a quick visual check for the control signal presence. If the LED is on but the load isn't switching, investigate the load circuit.
9. Warranty & Support
LCTC products are manufactured to high-quality standards and are CE certified. For technical support or warranty inquiries, please contact your local distributor or the manufacturer directly. Please have your product model (SSR-41FDD or SSR-41FDA) and any relevant purchase information ready when contacting support.