JIKONG RS485-USB Connector Cable

Contents

JIKONG BMS RS485-USB Connector Cable Instruction Manual

This manual provides detailed instructions for the installation, operation, and troubleshooting of your JIKONG RS485-USB Connector Cable.

1. Introduction

The JIKONG USB to TTL module is a dedicated isolated USB to TTL module designed for JIKONG BMS GPS interfaces. It allows convenient connection of the BMS to a computer. This module enables users to access internal BMS data, adjust parameters, and perform firmware updates via PC software, ensuring optimal system performance.

This cable is specifically designed for use with JIKONG BMS models: JK-PB1A16S10P, JK-PB1A16S15P, JK-PB2A16S15P, and JK-PB2A16S20P.

JIKONG RS485-USB cable with compatible BMS models listed
JIKONG RS485-USB cable compatible with specific JKBMS models.

2. Features

  • Compatible with 5V and 3.3V TTL levels.
  • 1500VDC isolated power module for enhanced safety.
  • Equipped with LED status indicators for easy monitoring.
  • Supports a maximum baud rate of 256000bps for fast data transfer.
  • Certified with CE, FCC, and RoHS standards.

3. Specifications

AttributeValue
BrandJIKONG
TypeRS485-USB Connector Cable
Compatible BMS ModelsJK-PB1A16S10P, JK-PB1A16S15P, JK-PB2A16S15P, JK-PB2A16S20P
Cable Length2 meters (Total)
Cable Dimensions8.5 x 2.5 mm (flat cable)
InterfaceUSB to RJ45
Baud RateMax 256000bps
Isolation1500VDC isolated power module
CertificationsCE, FCC, RoHS
Product Dimensions (Connector)Length: 53.00 mm, Width: 24.00 mm, Height: 14.00 mm
JIKONG RS485-USB cable dimensions and internal chip
Cable dimensions and internal JIKONG RS485 chip.

3.1. Pin Definitions (RJ45 Connector)

Product interface definition diagram
Diagram of the RS485-USB connector pinout.
Pin NameDefinition
GNDConnects to external device GND
TXTransmit data pin, connects to external device RX pin
RXReceive data pin, connects to external device TX pin

4. Package Contents

The package contains one (1) JIKONG RS485-USB Connector Cable. Please note that the BMS interface board is not included and must be purchased separately if required.

Close-up of the JIKONG RS485-USB cable
JIKONG RS485-USB Connector Cable.

5. Setup and Connection

  1. **Connect to PC:** Plug the USB end of the module into your computer's USB port.
  2. **Driver Installation:** Open Device Manager on your PC and verify that the CH340 device is recognized and working correctly. Note the assigned COM port (e.g., COM7). If the driver is not installed (indicated by a yellow exclamation mark), download and install it from: https://www.wch.cn/download/CH341SER_EXE.html.
  3. Device Manager screenshot showing CH340 driver
    Verify CH340 driver installation in Device Manager.
  4. **Connect to BMS:** Connect the RJ45 end of the cable to the GPS interface on your JIKONG BMS protection board.
  5. JIKONG RS485-USB cable connected to a JIKONG Interface Board
    Physical connection of the RS485-USB cable to the BMS interface board.
  6. **BMS APP Settings:** Power on the BMS. Use the mobile APP to set the BMS parameters. Ensure the device address is set to '1' and Serial Port 1 Protocol is set to '1'.
  7. Mobile APP settings screenshot
    Screenshot of mobile APP settings for device address and protocol.
  8. **Connect to PC Software:** Open the JIKONG PC monitoring software. In the bottom right corner, enter the device address and the COM port number identified in step 2. Click 'Connect'.

6. Operating the PC Software

The JIKONG PC software provides various functions for monitoring and managing your BMS. Below are the main sections:

  1. **Real-time Status Page:** This page displays real-time data such as battery voltage, charging/discharging current, alarm status, battery health, and balance group information.
  2. PC software real-time status screenshot
    Real-time status display in the JIKONG PC software.
  3. **Parameter Settings Page:** To modify any parameters on this page, you must first click 'Authorization Settings' and enter the default factory password: '123456'. This allows you to adjust various operational parameters of the BMS.
  4. PC software parameter settings screenshot
    Parameter settings interface, requiring authorization.
  5. **BMS Control Page:** Similar to the parameter settings, access to BMS control functions requires 'Authorization Settings' with the default password '123456'. This section allows you to control specific BMS operations.
  6. PC software BMS control screenshot
    BMS control panel, requiring authorization.
  7. **System Log Page:** Use the 'Update Log' button to refresh the internal BMS log data to the PC software. The 'Export Log' button allows you to save all current log data to a specified folder on your computer in XLSX format, viewable with Excel or similar software.
  8. PC software system log screenshot
    System log display and export options.
  9. **Fault Download Page:** The 'Download Fault' button retrieves internal BMS fault logs to the PC software. The 'Export Fault' button saves all displayed fault logs to a specified folder on your computer in XLSX format.
  10. PC software fault download screenshot
    Fault log download and export options.
  11. **About BMS Page:** This page provides essential information about your BMS, including the model, hardware version, software version, and total power-on time.
  12. PC software About BMS screenshot
    About BMS page showing device information.
  13. **Firmware Upgrade Function:** Click the 'Upgrade Firmware' icon in the top right corner of the PC software. Select the appropriate firmware file to proceed with a normal upgrade.
  14. PC software firmware upgrade screenshot
    Firmware upgrade interface.
  15. **Forced Upgrade Function:** In cases where the device is 'bricked' or a mandatory firmware update is required, use the 'Forced Upgrade' function. Select the firmware file and click 'Forced Upgrade'. This process requires an authorization code from the manufacturer.
  16. PC software forced upgrade screenshot
    Forced firmware upgrade interface, requiring an authorization code.

7. Maintenance

  • Keep the connector cable clean and dry. Avoid exposure to moisture or extreme temperatures.
  • Handle the cable gently to prevent damage to the connectors or wiring.
  • Store the cable in a safe place when not in use to prevent tangling or physical stress.
  • Regularly check the connectors for any signs of wear or corrosion.

8. Troubleshooting

If you encounter issues while using the JIKONG RS485-USB Connector Cable, please follow these steps:

  1. **Check Connections:** Ensure that the module, your computer, and the BMS protection board are all correctly and securely connected.
  2. **Verify Driver Installation:** Confirm that the CH340 driver is properly installed on your computer. Refer to Section 5.2 for driver installation instructions.
  3. **BMS APP Settings:** Use the mobile APP to check if the BMS settings (device address and communication protocol) are correctly configured. Refer to Section 5.3 for details.

9. User Tips

  • Always ensure the correct COM port is selected in the PC software to establish a successful connection.
  • When performing firmware updates, ensure a stable power supply to both the BMS and the computer to prevent interruptions.
  • Keep your JIKONG PC software and mobile APP updated to the latest versions for optimal performance and new features.

10. Warranty and Support

For detailed warranty information, technical support, and additional documentation, please refer to the official JIKONG resources. A comprehensive user manual in PDF format is available for download:

Download User Manual (PDF)

JIKONG is committed to providing high-quality products and excellent customer service. If you have any questions or require assistance, please contact JIKONG customer support.

Video: JIKONG BMS product showcase, demonstrating various features and accessories.

© 2024 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.