1. Introduction
This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your WINXU Ebike Brushless Motor Drive Controller and SW900 Colour LCD Kit. This kit is designed for electric mountain bikes and scooters, offering a high-power, efficient, and stable drive experience.
The controller is a 3-mode sine wave controller specifically for brushless gearless motors and geared Hall motors. It features low noise, strong power, and stable drive, supporting up to 40A current. The self-learning wires ensure compatibility with almost all brushless motors.
2. Safety & Warnings
Read all instructions before use to ensure safety and prevent damage.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Always disconnect the battery power supply before installing or performing any work on the controller to prevent damage to the equipment.
- Ensure all connections are secure and correctly wired, especially high-current connections like motor phase wires and battery. Incorrect connections can lead to short circuits, overheating, and damage.
- This controller is for brushless motors only. It is not suitable for brush motors.
- The motor requires a Hall sensor for proper operation. If using a Hall-less brushless motor, the LCD will continuously display the E07 error code.
- If using PAS (Pedal Assist System), please use dual Hall PAS sensors.
3. Specifications
| Feature | Specification |
|---|---|
| Brand Name | WINXU |
| Type | Controller |
| Input Voltage | 36V / 48V / 60V |
| Motor Power Compatibility | 1000W / 1500W / 2000W (Also compatible with 250W / 350W / 500W / 750W) |
| Max Current | 40A |
| Motor Type | Brushless Motor (with Hall sensor recommended) |
| LCD Model | SW900 Colour LCD |
| Protocol Type | UART |
| Controller Dimensions (L x W x H) | Approx. 190mm x 83.5mm x 45mm (7.48in x 3.28in x 1.77in) |
| LCD Dimensions (L x W) | Approx. 110mm x 61.5mm (4.33in x 2.42in) |
| Controller Material | Aluminum alloy (for heat dissipation) |
| Waterproof Rating | IPX6 (Controller) |
| Package Weight | 1.1 kg |
| Package Dimensions (L x W x H) | 26cm x 15cm x 9cm |




4. Setup and Installation
4.1 Pre-use Preparation
Before installing the controller, always disconnect the battery power supply. Do not work with the power on, as it may easily damage the equipment.
4.2 Product Wiring Diagram
Before starting the installation, carefully read the wiring diagram and fully understand the functions of all connectors before proceeding.


4.3 Connector Function Introduction and Installation Steps Reference
- Motor Phase Wire: Connect the 3-phase wires (thick wires) of your motor, matching yellow, green, and blue according to the color code. Ensure a secure connection, as this connector handles a relatively large driving current.
- Motor Hall Sensor: Connect the motor Hall sensor. This controller uses a 6-wire Hall sensor. Red, yellow, and blue are the Hall signal wires; red and black are the working voltage cables; and white is the motor speed signal cable. Connect according to the correct colors. If your motor has a 5-wire Hall sensor, ignore the white speed signal cable; the controller will automatically obtain the motor speed signal from the Hall signal cable.
- LCD Display (SW900): This connector is a 5-pin design, using a UART protocol LCD display. Red and black are for operating voltage; blue is for controller power control; green is RX, and yellow is TX.

Figure 8: SW900 LCD Display Wiring Diagram, showing the SM-5P connector for the LCD and a 2P connector for an optional headlight (not included). - Power Lock: This connector is a key lock connector. If your original bicycle has a key lock, connect the key lock switch to this connector. If your bicycle does not have a key lock, you can ignore it.
- Throttle: This connector is for installing a Hall throttle (thumb or twist type). The throttle receives a signal voltage of 1.1-4.2V. Red and black are the operating voltage, and white is the Hall signal. Ensure correct connection during installation.
- PAS Sensor: This controller uses a magnetic pulse type PAS sensor and is compatible with universal type PAS sensors. When ordering a PAS sensor, ensure it is a universal type. Red and black are power voltage wires, and blue is the pulse signal cable.
- Speed Limit: The speed limit connector is used for external speed limiting. When this connector is plugged in, the controller activates a speed limit mode, with a maximum speed limit in the range of 15-27 km/h. Note that this controller does not support P08 speed limit settings from the LCD.
- Low-Level Brake: This is a power-off braking system that automatically cuts off the motor power supply when the brake is applied. The black cable is the negative wire, and the white cable is the brake signal cable. If your brake is a low-level type with 2 cables, connect it correctly.
- Light Power: This connector outputs battery voltage for powering devices such as headlights, brake lights, horns, and USB chargers. Yellow is the positive terminal and black is the negative terminal.
- Battery: This is the device's power supply. Connect the positive and negative terminals correctly. If connected incorrectly, the controller may short circuit, overheat, and be damaged. Connect the battery in the last step and carefully check for short circuits in other components and proper connections before connecting. Double-check for reverse polarity.
- Automatic Detection (Self-Learning Cable): This connector is used for motor matching operations. After the first installation, use this connector to complete the motor matching process. After turning on the device, lift the motor hub in the air and plug in this connector. The motor will then start driving. If the motor drives in the opposite direction, disconnect and reconnect the connector to change the driving direction. Once the motor drives in the correct direction and without vibration, disconnect the self-learning cable.
5. Operation
5.1 SW900 LCD Display Overview

- Up Button (^): Short press to change gear. Long press to control headlight.
- M Button: Long press to switch on/off. Short press to switch mileage/voltage display.
- Down Button (v): Short press to change gear. Long press to enter cruise mode (Note: Cruise mode is not supported by this controller, this button operation is invalid).
5.2 How to Enter Setup Mode
Long press the + and - buttons simultaneously for 3-5 seconds after switching on the LCD to enter the setting mode. The parameters will blink. Short press the M button to switch between parameters, and use the + and - buttons to select or adjust parameter values.
5.3 LCD Parameter Introduction
| Parameter | Description |
|---|---|
| P00 | Restore factory setting (Controller not supported) |
| P01 | Backlight Brightness |
| P02 | Mileage unit |
| P03 | Voltage selection |
| P04 | Sleep Time |
| P05 | PAS Gear |
| P06 | Wheel Diameter (in inches, for accurate speed display) |
| P07 | Speed Magnet (normally set to 23, for accurate speed display) |
| P08 | Speed Limit (Controller not supported for LCD setting) |
| P09 | Zero Start / Non-Zero Start |
| P10 | Drive mode setting (0: PAS drive, 1: throttle drive, 2: PAS and throttle drive) |
| P11 | PAS sensitivity setting |
| P12 | PAS start strength setting |
| P13 | PAS magnet disc type setting |
| P14 | Current Limit Setting (Controller not supported) |
| P15-P19 | Functions not yet opened, please ignore and do not set up. |
5.4 Speed Display Calibration
For accurate LCD speed display, enter LCD setting mode and set your motor wheel diameter in P06 (in inches). Set the speed magnet in P07 (normally 23). After setting P06 and P07, test the real-time speed using a map navigation app. If the LCD display speed is higher than the navigation app's speed, reduce the P07 parameter. If the LCD display speed is lower, increase the P07 parameter until the LCD displays the exact speed.
6. Maintenance
- Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth.
- Storage: Store the device in a dry place at room temperature (15°C - 35°C).
- Long-term Storage: If not used for a long time, charge the device to 50% every 3 months to maintain battery health.
7. Troubleshooting & Error Codes
7.1 E07 Display After First Installation
After the controller is installed for the first time, the device may display the E07 error code if motor matching and parameter detection have not been completed. To resolve this, use the self-learning cable (as described in Section 4.3, point 11) to complete the motor matching operation. Once motor matching is complete, use the throttle and high-speed gear to drive the motor at high speed. The controller will detect motor parameters and status. If no fault is detected during high-speed driving, the controller will automatically remove the E07 error code. If it still displays, it indicates insufficient driving speed or a fault with the motor or motor Hall sensor; please check the motor.
7.2 LCD Error Code Explanation
| Code | Description |
|---|---|
| E00 | Normal status |
| E01 | (No specific description provided in documentation) |
| E02 | Brake fault |
| E03 | PAS sensor fault |
| E04 | 6KM/H cruise mode (Note: Cruise mode is not supported by this controller) |
| E05 | Real-time cruise (Note: Cruise mode is not supported by this controller) |
| E06 | Battery undervoltage |
| E07 | Motor failure (Will always display if using a Hall-less motor or if Hall sensor is damaged) |
| E08 | Throttle fault |
| E09 | Controller failure |
| E10 | Communication signal reception failure |
| E11 | Communication signal transmission fault |
| E12 | BMS communication fault |
| E13 | Headlight fault |
8. User Tips
- Motor Compatibility: This controller is designed for brushless motors, specifically those with Hall sensors. If your motor is Hall-less or has a damaged Hall sensor, the LCD will continuously show an E07 error. Consider this before purchase if you cannot accept the persistent error code.
- Initial Setup - Self-Learning: Always use the self-learning wires during the first installation to match the controller with your motor parameters. This prevents motor jitter and ensures proper operation. If the motor initially spins in reverse, simply short-connect the self-learning wires again to reverse the direction.
- Speed and Current Limits: This controller does NOT support speed limits (P08) or current limits (P14) set via the LCD. The external speed limit connector only limits speed to 6 km/h, not 25 km/h. If you require a 25 km/h speed limit, this controller may not meet your needs. It is primarily suited for users seeking high-speed performance and modification flexibility.
- Cruise Mode: This is a true sine wave controller and does NOT support cruise mode or 6 km/h mode. The cruise button operation on the LCD is invalid.
- PAS Sensor: For pedal assist functionality, ensure you use dual Hall PAS sensors.
- Battery Compatibility: The controller supports 36V, 48V, and 60V batteries. A 52V battery is compatible.
9. Warranty & Support
For additional item guides and documents, please refer to the official user manual PDF available from the seller. This PDF contains detailed information regarding product usage and specifications. The PDF can be found at: User manual (PDF)
Manufacturer Information:
- Name: ShenZhen Winxu Technology Co,.Ltd
- Address: No.118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China
- E-mail: Winxutech@163.com
- Tel: +86-15814065441
EU Authorized Representative:
- Name: Vermilion Bird OU
- Address: Tartu mnt 67/1-13b, Kesklinna linnaosa, 10115 Tallinn Harju maakond, Estonia
- E-mail: vermilionbird.eu@outlook.com
For further assistance or inquiries, please contact the manufacturer or their authorized representative using the details provided above.
10. Disposal & Recycling
This product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.
