UGREEN CM777--25665

Contents

UGREEN 20Gbps M.2 SSD Case Instruction Manual

Model: CM777--25665

UGREEN 20Gbps M.2 SSD Case NVMe SATA SSD Enclosure Adapter USB 3.2 Gen2 External Enclosure Supports RGB Lighting effect

1. Introduction

The UGREEN 20Gbps M.2 SSD Case is a high-performance external enclosure designed to house M.2 NVMe or SATA solid-state drives, transforming them into portable storage solutions. Featuring a USB 3.2 Gen 2x2 Type-C interface, it supports data transfer speeds of up to 20Gbps. The enclosure also includes dynamic RGB lighting effects and an advanced heat dissipation system to ensure optimal performance and drive longevity.

UGREEN M.2 SSD Case with cables, highlighting 20Gbps, USB3.2 Gen 2x2, NVMe/SATA, RGB.

Figure 1: UGREEN 20Gbps M.2 SSD Case

2. Package Contents

  • UGREEN 20Gbps M.2 SSD Case
  • USB-C to USB-C Cable
  • USB-C to USB-A Cable (may vary by model/package)
  • User Manual (this document)

3. Setup Guide

Follow these steps to install your M.2 SSD into the enclosure:

  1. Open the Enclosure: Gently slide open the enclosure cover to reveal the internal M.2 slot.
  2. Insert the SSD: Carefully align your M.2 NVMe or SATA SSD with the M.2 slot inside the enclosure. Insert the SSD at an angle and then gently press it down.
  3. Secure the SSD: Use the provided fastener (e.g., screw or rubber stopper) to secure the M.2 SSD in place. Ensure it is firmly seated to prevent movement.
  4. Apply Thermal Pad: Place the included silicone thermal pad onto the SSD chip(s) to facilitate heat transfer to the aluminum housing.
  5. Close the Enclosure: Slide the enclosure cover back into place until it clicks securely.
Exploded view of the UGREEN M.2 SSD enclosure, showing aluminum housing, thermal pad, and M.2 SSD for heat dissipation.

Figure 2: SSD Installation and Heat Dissipation Components

The enclosure supports various M.2 SSD sizes:

Diagram illustrating compatibility with various M.2 SSD sizes (2230, 2242, 2260, 2280).

Figure 3: Supported M.2 SSD Sizes (2230, 2242, 2260, 2280)

4. Operating Instructions

The UGREEN M.2 SSD Case is designed for plug-and-play operation. No drivers are typically required for most operating systems.

  1. Connect to Device: Use the provided USB-C cable to connect the enclosure to a compatible USB-C port on your computer, laptop, tablet, or gaming console. For optimal 20Gbps speeds, ensure your device has a USB 3.2 Gen 2x2 Type-C port.
  2. Access Storage: Once connected, the SSD will appear as an external storage device on your operating system. You may need to format the SSD if it's new or if you wish to change its partition scheme.
  3. RGB Lighting: The enclosure features dynamic RGB lighting effects that illuminate during data transmission, indicating activity.
User connecting the UGREEN M.2 SSD enclosure to a laptop.

Figure 4: Connecting to a Laptop

Diagram showing device compatibility (motherboard, laptop, iPad, iPhone, PS5) and operating system compatibility (Windows, Mac OS, Android, Linux).

Figure 5: Device and System Compatibility

User playing a game on a desktop computer with a PS5 and the UGREEN M.2 SSD enclosure connected.

Figure 6: Usage with Gaming Setup

5. Maintenance

To ensure the longevity and optimal performance of your UGREEN M.2 SSD Case:

  • Heat Dissipation: The enclosure features an aluminum housing and a silicone thermal pad for efficient heat dissipation. Ensure the enclosure is not covered or placed in an area with poor airflow during extended use.
  • Cleaning: Use a soft, dry cloth to clean the exterior of the enclosure. Avoid using harsh chemicals or abrasive materials.
  • Storage: When not in use, store the enclosure in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Handle the enclosure with care to avoid physical damage.

6. Troubleshooting

  • SSD Not Recognized:
    • Ensure the M.2 SSD is correctly installed and securely fastened within the enclosure.
    • Try connecting the enclosure to a different USB port or a different computer to rule out port or system issues.
    • For new SSDs, ensure they are initialized and formatted in Disk Management (Windows) or Disk Utility (Mac OS).
    • Verify that your SSD is either NVMe or SATA M.2 type, as the enclosure supports both.
  • Slow Transfer Speeds:
    • To achieve the maximum 20Gbps transfer speed, ensure your host device (computer, laptop) has a USB 3.2 Gen 2x2 Type-C port. Connecting to older USB standards (e.g., USB 3.0/3.1 Gen 1, USB 3.1 Gen 2) will result in lower speeds.
    • Ensure you are using the provided high-quality USB-C cable.
    • Check if other applications or processes are heavily utilizing system resources or disk I/O.
  • RGB Lights Not Working:
    • Ensure the enclosure is properly connected and the SSD is active (e.g., transferring data). The RGB lights typically indicate activity.
    • If the SSD is recognized and working but lights are off, try reconnecting the enclosure.

7. Specifications

FeatureSpecification
BrandUGREEN
Model NumberCM777--25665
InterfaceUSB 3.2 Gen 2x2 Type-C
Data Transfer RateUp to 20Gbps
SSD CompatibilityNVMe/SATA M.2 SSDs (2230, 2242, 2260, 2280)
Max. Supported Capacity8TB
Case MaterialAluminum
Operating System SupportWindows, Mac OS, Android, Linux

8. Warranty and Support

UGREEN products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the official UGREEN website or contact UGREEN customer service directly. Keep your purchase receipt for warranty claims.

9. User Tips

  • Not a Portable Hard Drive: This product is an enclosure for an M.2 SSD, not a pre-installed portable hard drive. You need to purchase and install an M.2 SSD separately.
  • Dual Protocol Support: The enclosure supports both NVMe and SATA M.2 SSDs, offering broad compatibility. Ensure your SSD is an M.2 form factor.
  • Maximize Speed: To achieve the advertised 20Gbps speed, connect the enclosure to a device equipped with a USB 3.2 Gen 2x2 port. Older USB ports will function but at reduced speeds.
  • Initial Setup: Remember to initialize and format new SSDs through your operating system's disk management tools before first use.

© 2023 UGREEN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.