EWIND EW-PD101G-AF-5

Contents

EWIND POE Splitter Instruction Manual

Model: EW-PD101G-AF-5

1. Product Overview

The EWIND POE Splitter (Model EW-PD101G-AF-5) is designed to separate Power over Ethernet (PoE) signals into distinct power and data streams. This allows non-PoE compatible devices, such as IP cameras, wireless access points, and other network devices, to be powered and connected to a network using a single Ethernet cable from a PoE-enabled switch or injector. It supports IEEE802.3af standard and provides a stable 5V DC power output.

EWIND POE Splitter front view
Front view of the EWIND POE Splitter.
EWIND POE Splitter Cable with port descriptions
The POE Splitter cable showing the 8-Pin RJ45 female input, RJ45 male output, and DC (5.5x2.1mm) male output ports.

2. Package Contents

Please verify that all items are present and in good condition:

  • 1 x EWIND POE Splitter (Model EW-PD101G-AF-5)
  • (Additional accessories, if any, would be listed here)

3. Installation and Setup

Follow these steps to properly install your POE Splitter:

  1. Identify Components: Locate your PoE-enabled switch or injector, the non-PoE device requiring power and data, and the EWIND POE Splitter.
  2. Connect PoE Input: Connect an Ethernet cable from your PoE-enabled switch or injector to the 8-Pin RJ45 female input port on the POE Splitter. This port receives both power and data.
  3. Connect Data Output: Connect the RJ45 male output cable from the splitter to the network input port of your non-PoE device. This provides the data connection.
  4. Connect Power Output: Connect the DC (5.5x2.1mm) male output cable from the splitter to the power input port of your non-PoE device. This provides the 5V DC power.
  5. Verify Connections: Ensure all cables are securely connected. The non-PoE device should power on and establish a network connection.
Installation diagram for POE Splitter
Diagram illustrating the connection of the POE Splitter between a PoE switch and non-PoE cameras.
POE Splitter input and output diagram
Detailed view of the PoE input, signal output, and 5V power output connections.

4. Operation

Once properly installed, the EWIND POE Splitter operates automatically. It receives power and data from the PoE source and delivers them separately to your non-PoE device. No configuration is required for the splitter itself.

  • Power Delivery: Converts the incoming PoE voltage (DC 44-57V) to a stable 5V DC, 3A output, suitable for devices requiring up to 12W.
  • Data Transmission: Supports Ethernet data transfer rates of 10/100/1000Mbps, ensuring compatibility with various network speeds.
Wide range of applications for POE Splitter
Examples of devices compatible with the POE Splitter, including web video cameras, wireless APs, and surveillance systems.

5. Safety Features and Protection

The EWIND POE Splitter incorporates several safety features to protect connected devices and ensure reliable operation:

  • High Voltage Isolation: Provides 1500V isolation to prevent electrical interference and damage.
  • Short Circuit Protection: Automatically protects against damage from short circuits.
  • Over-current Protection: Safeguards devices from excessive current flow.
  • Over-temperature Protection: Prevents overheating during operation.
Isolation circuit protection features
Visual representation of the overvoltage, overcurrent, and short circuit protection features.
Internal circuit board highlighting isolation transformer and filter element
Internal view of the splitter's circuit board, showing the isolation transformer and filter element for enhanced protection.

6. Maintenance

The EWIND POE Splitter is designed for low maintenance. To ensure optimal performance and longevity:

  • Keep the device in a clean, dry environment.
  • Avoid exposing the splitter to extreme temperatures outside its operating range (-20°C to +60°C).
  • Do not block any ventilation points (if present).
  • Periodically check cable connections for looseness or damage.

7. Troubleshooting

If you encounter issues with your POE Splitter, refer to the following common troubleshooting steps:

  • No Power to Device:
    • Ensure the PoE-enabled switch or injector is powered on and functioning correctly.
    • Verify that the Ethernet cable from the PoE source to the splitter's input is securely connected and not damaged.
    • Check the DC power cable connection from the splitter to your non-PoE device.
    • Confirm your non-PoE device requires 5V DC power and uses a 5.5x2.1mm DC barrel jack.
  • No Network Data:
    • Check the Ethernet cable connection from the splitter's data output to your non-PoE device's network port.
    • Ensure the non-PoE device's network settings are correctly configured.
    • Test the Ethernet cables with another device to rule out cable issues.
  • Intermittent Connectivity:
    • Inspect all cable connections for looseness.
    • Ensure the operating environment is within the specified temperature range.
    • Verify that the PoE source is providing stable power.

8. Specifications

FeatureSpecification
Product NamePOE Splitter
Product ModelEW-PD101G-AF-5
Input VoltageDC 44-57V
Output PowerDC 5V 3A (12W Max Load)
Network ProtocolIEEE802.3af
Power Interface5.5x2.1mm DC Jack
Working Temperature-20°C ~ +60°C
Data Transfer Rate10/100/1000Mbps
POE Pinout Support1/2(+), 3/6(-) or 4/5(+), 7/8(-)
Isolation1500V High Voltage Isolation
Protection FeaturesShort Circuit, Over-current, Over-temperature
CertificationsCE, FCC, RoHS
Dimensions (Main Body)83mm (Length) x 29mm (Width) x 24mm (Height)
Cable LengthApproximately 180mm
Product parameters and dimensions of the POE Splitter
Detailed product parameters and physical dimensions of the EWIND POE Splitter.

9. User Tips

  • Always verify the voltage and current requirements of your non-PoE device before connecting it to the splitter to prevent damage. This splitter provides 5V DC.
  • Ensure the DC barrel jack size (5.5x2.1mm) matches your device's power input.
  • For optimal performance, use high-quality Ethernet cables (Cat5e or Cat6) for both input and output connections.
  • The splitter is compatible with various mainstream brands like Huawei, Cisco, HP, and Aruba, offering broad usability.
POE Splitter compatibility with major brands
The POE Splitter is fully compatible with mainstream brands such as Huawei, Cisco, HP, and Aruba.

10. Warranty and Support

This product is certified with CE, FCC, and RoHS standards, ensuring compliance with relevant safety and environmental regulations.

For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.