DIATONE MAMBA F722APP MK5 FC

Contents

Diatone Mamba F722 MK5 Flight Controller User Manual

Model: MAMBA F722APP MK5 FC

1. Introduction

The Diatone Mamba F722 MK5 Flight Controller (FC) is a high-performance component designed for FPV (First Person View) drones and other remote-controlled aircraft. It integrates essential features such as an OSD (On-Screen Display), multiple UARTs, and BEC (Battery Eliminator Circuit) outputs, providing a robust platform for advanced flight control. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance and longevity of your flight controller.

2. Specifications

The Mamba F722 MK5 Flight Controller boasts the following technical specifications:

FeatureSpecification
MCU216MHz STM32F722
GYROICM-42688-P
Target FirmwareMAMBA F722_2022B
OSDYes
Blackbox16M Flash Memory
BarometerSPL06
UARTs6 Sets
I2CYes
F.PortYes
RSSINo
Buzzer PadYes
CURR PadYes
ESC Signal8 Sets
ESC SoftDshot300/600
ESC TelemetryYes
Power LEDYes
LED ControllerBF LED
AIR UNIT PortYes
WIFINo
CAM1/CAM2 SwitchYes
Receiver ProtectionYes
TVS ProtectionYes
BEC Output3.3V 0.5A, 5V 3A, 12V 3A
Input Voltage4~6S Lipo (14.8~25.2V)
Mounting Size30.5mm x 30.5mm / M3
Weight10g
SocketSh1.0
Supply Connectors8pin sh1.0 ×1, AIR UNIT sh1.0 ×1

3. Setup and Wiring

Proper installation and wiring are crucial for the safe and correct operation of your flight controller. Refer to the detailed diagram below for all connections.

Diatone Mamba F722 MK5 Flight Controller Wiring Diagram
Figure 3.1: Comprehensive wiring diagram for the Diatone Mamba F722 MK5 Flight Controller, showing connections for receiver, GPS, VTX, camera, motors, buzzer, and LEDs. This diagram also details default port assignments, power indicators, CAM/CAM2 settings, and ESC compatibility with capacitor requirements.

3.1 Default Port Assignments

The flight controller comes with the following default port assignments, which are also illustrated in Figure 3.1:

  • Receiver: SBUS/IBUS/DSM
  • UART1: VTX
  • UART2: GPS
  • UART3: TARET
  • UART4: ESC Telemetry
  • UART5: Receiver
  • UART6: TELE
  • USB: Configuration

The target firmware for this FC is MAMBA F722_2022B, and the recommended configuration file is also MAMBA F722_2022B.

3.2 Power Indicators

The flight controller features dedicated LEDs to indicate the status of different voltage rails, as shown in Figure 3.1:

  • 12V LED
  • 5V LED
  • 3.3V LED

3.3 Camera (CAM1/CAM2) Settings

The FC supports switching between two cameras. Connect your primary camera to CAM1 and secondary to CAM2. The camera switch functionality requires 5V, GND, and Video signals for both cameras, as depicted in the wiring diagram.

3.4 Motor Connections

Connect your ESCs (Electronic Speed Controllers) to the motor output pads (M1, M2, M3, M4) on the flight controller. Ensure that the motor order and direction are correctly configured in your flight control software (e.g., Betaflight) to match your drone's frame layout.

3.5 ESC Compatibility and Capacitor Requirements

The Mamba F722 MK5 FC is designed to be compatible with various MAMBA ESCs. When operating with a 6S LiPo battery, it is essential to add a capacitor to the ESC power input. This helps to filter voltage spikes and ensure stable operation. Refer to the table below for recommended capacitor specifications based on common MAMBA ESC models:

ESC ModelOutput CurrentInput VoltageRecommended Capacitor (for 6S)
MAMBA F55_BLS ESC55A3-6S Lipo470uF/35V
MAMBA F55_128K ESC55A3-6S Lipo1000uF/35V
MAMBA F65_128K ESC65A3-6S Lipo1000uF/35V

4. Operating Instructions

The Diatone Mamba F722 MK5 Flight Controller operates using Betaflight firmware. After completing the physical wiring, you will need to configure the FC using the Betaflight Configurator software on your computer.

  • Firmware Flashing: The FC comes pre-flashed with MAMBA F722_2022B firmware. If you need to update or re-flash, ensure you download the correct target firmware from the official Betaflight website.
  • Configuration: Connect the FC to your computer via the USB-C port. Open Betaflight Configurator to perform initial setup, calibrate sensors, configure UARTs for peripherals (receiver, VTX, GPS), set up motor outputs, and tune PID settings.
  • Safety Precaution: Always remove propellers from your drone before connecting the flight controller to a power source or USB for configuration and testing. Betaflight is open-source software, and self-flashing firmware may void your warranty.

5. Maintenance

To ensure the longevity and reliable performance of your flight controller, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the FC for dust, dirt, or debris. Use compressed air or a soft brush to gently clean the board.
  • Avoid Moisture: Protect the flight controller from moisture and extreme temperatures. If operating in humid conditions, consider conformal coating.
  • Inspect Connections: Periodically check all soldered connections and connectors for signs of wear, corrosion, or loose contacts. Re-solder or replace as necessary.
  • Firmware Updates: Keep your Betaflight firmware updated to benefit from bug fixes and new features. Always back up your configuration before updating.

6. Troubleshooting

If you encounter issues with your Mamba F722 MK5 Flight Controller, consider the following troubleshooting steps:

  • No Power: Check battery connections, ensure correct polarity, and verify BEC outputs.
  • No Connection to Betaflight Configurator: Ensure the correct USB driver is installed. Try a different USB cable or port.
  • Motors Not Spinning/Incorrectly: Verify motor wiring, ESC calibration, and motor direction in Betaflight. Check ESC signal connections.
  • Unstable Flight: Re-check PID tuning, ensure all sensors are calibrated, and verify mounting orientation in Betaflight. Inspect for vibrations.
  • OSD Issues: Check OSD settings in Betaflight, ensure video signal is correctly routed through the FC.
  • Peripheral Not Working (GPS, VTX, Receiver): Verify UART assignments and baud rates in Betaflight. Check wiring for continuity and correct pinouts.

7. User Tips

Based on common user experiences, here are some tips for using your Diatone Mamba F722 MK5 Flight Controller:

  • Double-Check Wiring: Before powering up, always perform a thorough visual inspection and continuity check of all wiring to prevent shorts and damage.
  • Backup Configuration: After successfully configuring your FC in Betaflight, save a backup of your settings (CLI dump) to easily restore them if needed.
  • Start with Default PIDs: For initial flights, use the default PID settings in Betaflight and make small adjustments as you gain experience.
  • Propeller Safety: Always remove propellers when connecting to Betaflight or performing any work on your drone to prevent accidental injury.

8. Warranty and Support

For warranty claims or technical support, please contact the official DIATONE store or your authorized reseller. Keep your proof of purchase for any warranty-related inquiries. Note that modifications, improper installation, or use outside of specified parameters may void the product warranty.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.