Superun AS02R

Contents

Superun Raceable Treadmill AS02R User Manual

Model: AS02R

Introduction

This manual provides detailed instructions for the safe and effective use, assembly, operation, maintenance, and troubleshooting of your Superun Raceable Treadmill AS02R. Please read all instructions carefully before operating the treadmill.

For additional information, you may refer to the official user manual PDF: User Manual (PDF).

Safety Instructions

Electrical Requirements

This treadmill must be earthed and plugged into an appropriate electrical outlet that is properly installed and earthed in accordance with all local codes and ordinances.

This treadmill is for use on an earthed, dedicated circuit. Make sure that the treadmill is connected to an outlet having the same configuration as the plug. Do not use a ground plug adapter to adapt the power cable to a non-grounded outlet.

Important Voltage Information

Before plugging the power cable into an electrical outlet, verify that the voltage requirements for the site match the voltage of the treadmill that has been received. The power requirements for the unit include an earthed, dedicated circuit, rated for one of the following:

  • United Kingdom: 240 V, 50 Hz
  • Spain: 230 V, 50 Hz
  • Italy: 230 V, 50 Hz
  • Germany: 230 V, 50 Hz
  • France: 230 V, 50 Hz

⚠ WARNING: Shock and electrocution hazard.

  • Connect unit to an earthed outlet.
  • Do not use a voltage adapter.
  • Unplug unit and let sit 10 minutes before cleaning or performing maintenance. Electrical charge can remain in unit after unplugging.
  • Keep water and liquids away from electrical parts.
  • Do not attempt to fix electrical faults if unqualified to do so!

User Safety Precautions

Prior to Use

  • When you first assemble your treadmill, make sure to check your running belt before use.
  • Assemble the treadmill according to the instruction manual.
  • Consult your doctor before beginning any exercise program.
  • Read instructions and warning labels.
  • Read emergency stop procedures.
  • Inspect unit. If damaged, DO NOT USE.
  • Ensure every bolt and screw is securely tightened.
  • Place your feet on the side frames when starting or stopping the treadmill.

During Use

  • DO NOT use for stretching and DO NOT attach straps or other devices.
  • DO NOT allow children aged 12 or younger to be on or near the machine.
  • Stop exercising if you feel faint, dizzy, or encounter pain.
  • Change speed in small increments for safety.
  • Keep all clothing and accessories clear of moving parts.
  • Wait until the running belt comes to a complete stop before getting off.
  • DO NOT jump onto a moving running belt.

Exercise Safety Precautions

  • Use sports clothes and gym shoes.
  • Check your shoes regularly and see if there is any dust or hard particles attached which may cause unnecessary damage.
  • DO NOT use with bare feet.
  • This model should only be used at home. DO NOT use for commercial purposes.

Facility Safety Precautions

  • Connect the treadmill to a properly earthed outlet only.
  • DO NOT operate electrically powered treadmills in damp or wet locations.
  • Clip the safety key to your clothing.
  • Use caution when getting on or off the treadmill.
  • Keep the running belt clean and dry at all times.
  • After each use, wait until the treadmill comes to a complete stop and is level. Then, switch it off and unplug it. Next, remove the emergency safety key from the treadmill.
  • Check the treadmill for worn or loose components before each use. DO NOT use until worn or damaged parts are replaced.
  • Maintain regularly. Refer to Preventive Maintenance chapter.
  • DO NOT use the treadmill if: (1) the power cable is damaged; (2) the treadmill is not working adequately or (3) the treadmill has been dropped or damaged.
  • DO NOT place the power cable near heated surfaces or sharp edges.
  • DO NOT use the treadmill outdoors.
  • DO NOT use the treadmill with 2 or more people running at the same time.
  • Read the instruction manual completely before using the treadmill.
  • Ensure all users wear appropriate footwear on equipment.
  • Set up and operate the treadmill on a level surface. DO NOT operate in small restricted areas or on plush carpet.
  • As far as possible provide a 100 cm clearance at each side.
  • Be sure your treadmill is clear of walls, equipment and other hard surfaces.
  • Do not use the treadmill near any respiratory equipment, aerosols or sprays causing mist.
  • DO NOT modify the treadmill in any way. Any modifications will void the warranty.
  • All the data displayed by the monitor is for reference purposes only.

Safety Key

The safety key works as an emergency stop. In the event of falling off the treadmill, the safety key will be pulled out and the power will be switched off at once. Be sure the string is free of knots and has enough slack for you to workout comfortably with the safety key in place. Before using the treadmill, clip the safety key to your clothing.

  1. Confirm that the safety key is in place in the bottom of the console. The treadmill will not start without the key in its place.
  2. Check the safety clip does not fall off in an emergency situation. Carefully step backward until the key pulls out of the console. If the safety clip falls off your clothing, clip the key again to your clothing and repeat this step until the safety clip is properly attached to your clothes.
  3. Ensure the safety clip is secured to your clothing at all times during use.
  4. After use, remove the safety key from the treadmill.
  5. Store the safety clip on the item holder located on the left or right side of the monitor.

⚠ WARNING: Falling Hazard

When starting the unit:

  • Stand on the side frames.
  • Do not stand on running belt.

Warning Stickers

Warning stickers indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury. Carefully read the following caution and warning labels before using the unit.

Warning sticker: Hands Pinching
Hands Pinching
Warning sticker: Power down before folding
Power down before folding
Warning sticker: Electrical safety, connect to grounded outlet, do not use adapter, unplug before maintenance, keep liquids away, do not fix if unqualified.
Electrical Safety
Warning sticker: Keep fingers away from rear bumper and tailwheel
Keep fingers away

⚠ WARNING

Keep small children and pets a safe distance from treadmill when in use. It is strictly forbidden to touch any moving parts of the treadmill.

Setup

Preparing the Site

To find the ideal location to set up this treadmill, ensure that:

  • Area is well illuminated and well ventilated.
  • Surface is level.
  • There is enough space to access the unit and emergency dismount. If it is possible, keep a 100 cm clearance around each side.
  • Place the treadmill in an environment with a relative humidity range of 30-50%. Please ensure the temperature is kept constant. Do not use in a moist or damp environment as this may impact on the integrity and performance of the machine.

Diagram

Treadmill diagram with labeled parts: Phone Holder, Cup Holder, Monitor, Safety Key, Arm Rest, Vertical Frame, Motor Cover, Running Belt, Slope Support, Belt Adjustment.
Treadmill Components Diagram

Content Listing

The treadmill box contents include:

  • Treadmill Base
  • Phone Stand
  • Manual

Accessories

  • Safety Key
  • Power Cable
  • Oil Bottle
  • T Allen Key

Assembly (Model AS02R)

The treadmill has been assembled and tested at the factory, so you shouldn't have any problems putting all the parts together. Components are designed to fit together, and only basic tools are required for the assembly process.

  1. **Unfold the Frame:** Once you have removed your machine from the box, unfold the frame following the direction shown in the diagram below.
  2. Diagram showing unfolding the treadmill frame.
    Step 1: Unfolding the Treadmill Frame
  3. **Fasten Bolts:** Use the T-shaped Allen Key to fasten the bolts at the bottom of the frame on each side. Turn them clockwise to tighten.
  4. Diagram showing fastening bolts with an Allen key.
    Step 2: Fastening the Frame Bolts
  5. **Rotate Electronic Panel and Arm Rests:** Rotate the electronic panel and arm rests in the direction of the arrows shown in the diagram below.
  6. Diagram showing rotating the electronic panel and arm rests.
    Step 3: Rotating the Console
  7. **Connect Power:** Insert the power plug into the rear of the base and turn on the switch.
  8. Diagram showing power plug insertion and switch location.
    Step 4: Connecting Power

⚠ WARNING: Heavy Equipment

It is recommended that at least two people lift, move, and assemble the treadmill. Use safe lifting methods.

Folding & Unfolding The Treadmill

  1. **Folding:** Disconnect your treadmill from the power source and unplug the power cable from the machine. Use your T-shaped Allen Key to loosen the bolts at the bottom of each side of the frame and gently fold down following the direction in the figure above. You can then either slide the machine under a bed for example, or you can follow the figure further to stand the treadmill upright and lean it against a wall. If you are standing the treadmill upright the surface it's on MUST be level.
  2. **Unfolding:** Make sure your treadmill is laying flat on the floor, lift the frame following the figure above and use your T-shaped Allen Key to tighten the bolts at the bottom of each side of the frame. You can now reconnect your power supply.
Diagram showing the folding and unfolding process of the treadmill.
Folding and Unfolding the Treadmill

Operating Instructions

Read all instructions, warnings, and safety procedures located in the Safety chapter before using the treadmill.

Monitor Configuration

Treadmill monitor display showing time, speed, distance, and calories, along with icons for WiFi, Bluetooth, and app connection.
Treadmill Monitor Display
IconDescription
WiFi IconIlluminates when connection is successful.
Bluetooth IconIlluminates when connection is successful.
SpeedDisplays current exercise speed.
TimeDisplays current exercise duration (0:00-99:59).
DistanceDisplays current exercise distance (0.00-99.99 km).
CaloriesDisplays current calorie consumption (0.0-9999 Kcal).

Control Buttons

Treadmill control panel with Start/Pause, Speed Decrease, 6 kph, 9 kph, Speed Increase, and Stop buttons.
Treadmill Control Panel
ButtonFunction
Start/Pause ButtonIn standby, press to activate the treadmill, press again to start. During operation, press to pause (retains data), press again to resume.
Speed Decrease ButtonDecreases running belt speed.
6.0 kph ButtonQuickly changes speed to 6.0 kph.
9.0 kph ButtonQuickly changes speed to 9.0 kph.
Speed Increase ButtonIncreases running belt speed.
Stop ButtonStops the treadmill and clears exercise data.

Testing the Treadmill Operation

Use the following instructions to test the full speed of the treadmill and to check the belt for proper operation. We recommend that the treadmill is unplugged or the power is switched off when not in use.

  1. Without anyone on the machine, plug the treadmill in. Ensure the power cable is not being pinched under the front of the treadmill.
  2. Locate the power switch on the end of the treadmill. Switch it to the on position. The display will light up.
  3. Add your safety key into the safety lock position. 'SAFE' should disappear from the panel.
  4. Press the START button and the treadmill will start to move at 1.0 kph. Check if the monitor is working normally.
  5. Observe the belt to see if it is running properly; it should be centred in the middle of the deck. If you have problems with the running belt operation, see "Adjust Running Belt" in the Maintenance chapter.
  6. Press the + and - buttons to check whether they are working. Run the treadmill through its full speed range. First press the + button until the treadmill reaches its highest speed. Then press the - button until the treadmill is back to 1.0 kph.
  7. Press the STOP button and check if the machine stops working.

Stopping the Treadmill

Press PAUSE once to pause the workout session. The treadmill will smoothly stop and the accumulated data will be displayed. Press STOP to end the workout session.

Emergency Dismount

If you experience pain, feel faint or need to stop your treadmill in an emergency situation, simply pull the safety key off the console. The running belt will then immediately stop.

PitPat App Connection

Download the PitPat app on your device via the app store or Google Play, or scan the QR code.

QR code for PitPat app download.
PitPat App QR Code

Launch the app and navigate through the user prompts to register or login with your account. Secure your workout equipment connection by following these steps:

  1. Activate the Bluetooth function on your smart phone and ensure the location service is switched on as well.
  2. Access the PitPat application and consent to any requested permissions.
  3. Navigate to the home screen of your mobile device and tap the running machine icon located at the top right corner. This will direct you to the search interface within the program. Your phone will automatically detect nearby connected devices, including your treadmill with an identifier beginning with “PitPat-T”. Once detected, select your treadmill to establish a successful link. A single beep from your treadmill indicates a completed connection, which is accompanied by brightening of the icon displayed on its panel display.

Note:

  • During this connection process, it's essential to maintain an active internet connection on your smart phone in order to have full control over the treadmill via the app.
  • Our model is exclusively compatible with a 2.4 GHz frequency range. Ensure your internet access point can support 2.4 GHz frequencies.
  • If the connection fails or is disrupted, wait until the signal stabilizes before restarting the treadmill in order to reconnect to the internet.

Video demonstrating treadmill setup and app connection.

Maintenance

Maintenance must be performed on a regular basis. Performing maintenance actions can aid in providing safe and trouble-free operation of all equipment.

Proper maintenance helps keep the treadmill in the best condition while improper maintenance may damage or shorten the life span of the treadmill.

During maintenance, disconnect the power cable.

Preventative Maintenance Activities

  1. Regularly clean and maintain the treadmill, ensuring all components are kept immaculate.
  2. After each use of the treadmill, employ a pristine towel or cloth to wipe down vital areas such as the console, depleting sweat and debris. Take care not to allow electrical elements or running belt to come into contact with water.
  3. Seek to position your treadmill in an area that is clean, dry, and free from moisture. Ensure it is powered off and disconnected from its socket prior to storage.
  4. Ease of transportation is incorporated within this product, equipped with wheels for seamless relocation. Prior to shifting the treadmill, ascertain it is unplugged and correctly folded.
  5. Conduct constant checks on the individual parts of the treadmill and ensure they are securely fastened. Components exhibiting signs of damage should be swiftly replaced.
  6. Prior to commencing exercise, the running belt has been appropriately adjusted; however, with continuous usage, there may be varying degrees of stretching experienced by the belt. This may result in wearing out the belt due to its deviation from the centre and friction with the side roller and rear cover. Belt slippage over time is common. If the running belt slips or gets stuck during movement on the treadmill, you can adjust the belt for better performance.

PLEASE NOTE:

Factors such as where the item is stored and how often the machine is used will affect the length of time between the necessary maintenance. It is recommended to perform this maintenance every six weeks.

Treadmill Lubrication

  1. The treadmill must be lubricated after half a year or a cumulative run of 100 hours. Add 1/3 to 1/2 bottle at a time.
  2. Confirm the lubrication status. With the treadmill off, lift the running belt from one side and reach for the surface under the running belt, and if the lubricant can be touched, there is no need to add more lubricant. But if the lubricant dries up, refill it with it. (Use only non-petroleum-based lubricants).
  3. Follow the figure above to properly add the lubricant.
  4. After lubricating, run the treadmill at 5.0 kph for 10-20 seconds to evenly spread the oil.
Diagram showing the steps for treadmill belt lubrication.
Treadmill Lubrication Steps

How to Check if the Running Belt is Loose

After a period of time, the user will feel there is a pause sensation whilst running. The running belt can become loose and stretch a bit over time causing a slipping sensation if it is not adjusted and tightened when needed.

If the belt is too tight, this may cause damage to your motor and/or roller. A belt too loose or too tight can cause wear and tear of both the belt and the board.

You can check if your belt is too loose by setting the speed to 1.0 kph then walking on the machine and try to stop the running belt with your feet while holding the handlebars and pulling your body in the opposite direction. If the belt stops, it means that it is loose and needs to be tightened.

Tightening the Running Belt

  1. Power off the treadmill.
  2. Turn the two belt adjustment screws located at the end of the belt clockwise to tighten the belt slightly by quarters. You must turn each screw on each side by the same amount to keep the belt aligned.
  3. Get back on the treadmill and check the belt (read description above). If it is still loose, re-adjust the belt screws by another quarter until you get the required tension on the belt.
  4. Run the machine on its own for 1-2 minutes to see if the belt stays centred.
Diagram showing how to tighten the running belt screws with an Allen key.
Tightening the Running Belt

Aligning the Running Belt

Usually between the frames and the running belt there should be a gap of 5-6 mm on both sides. If that gap is different it means that the belt is eccentric. So you have to put it back to the right position by following these steps:

  1. Power on and set the speed at 2.0-4.0 kph and adjust the screw at the end of the treadmill slowly with the Allen key.
  2. If the belt slants to the left, adjust the left bolt clockwise or adjust the right bolt anti-clockwise. If the belt slants to the right, adjust in the opposite manner.
  3. While adjusting the belt, check if the gap of difference has disappeared. If it is still there, screw the bolt again. Repeat this procedure until the running belt is in the centre. It does not need to be aligned perfectly, but ensure it is not scraping or rubbing on anything on the sides.
  4. Set the speed at 9.0 kph to check if the running belt is still in the same position. Once you have checked that, the treadmill is ready to use.
Diagram showing how to align the running belt, with illustrations of left and right adjustments.
Aligning the Running Belt

Troubleshooting

This section provides solutions for common error codes and issues you might encounter with your treadmill.

Error CodeDescriptionTroubleshooting Solutions
SAFESafety lock switch falls offPlace the magnet end of your safety key on top of the label described in the Safety Key section.
Er1Communication failure, the electronic panel cannot receive signal(1) Check for loose, disconnected or damaged communication cables.
(2) Check or replace the electronic panel if needed.
(3) Check or replace the controller if needed.
Er3Over-voltage(1) Check whether the voltage of the power supply is at a normal level of AC 220V.
(2) Check or replace the controller.
(3) Check or replace the motor.
Er4 / Er5Over-current / Overload(1) Check for overload status.
(2) Check if any mechanical moving part is stuck.
(3) Check the level of film release agent. The lack of film release agent may increase the friction between the running belt and the running board, which causes over-current.
(4) Check the running board for severe wear.
(5) Check the running belt for severe wear.
(6) Check if any short circuit exists in the motor line.
(7) Check or replace the controller.
(8) Check or replace the motor.
Er6Motor is not connected(1) Check for loose or disconnected lines for the motor.
(2) Check or replace the controller.
(3) Assess the need to replace the controller.
Er7Communication failure, the controller cannot receive signals(1) Check for loose, disconnected or damaged communication cables.
(2) Check or replace the electronic panel.
(3) Check or replace the controller.
Er13IGBT Short Circuit(1) Ascertain whether the treadmill is experiencing severe interference from external signals.
(2) Examine or replace the controller if necessary.
Er14Load Short Circuit(1) Check if there is any foreign object at the output of the controller that causes a short circuit.
(2) Check or replace the motor.
E02Main motor open circuit(1) Re-reinforce the main motor connection wire.
(2) Replace the motor.
(3) Replace the controller.
E03Motor over-voltage protection(1) Need to increase the external filter regulator.
(2) Reset the wheel diameter value to try not to exceed the rated voltage of the motor.
(3) Replace the controller.
E05Over-current protection(1) Reduce the load, try not to exceed the rated load.
(2) Remove stuck foreign bodies.
(3) Add lubricant.
(4) Replace the controller.
(5) Replace the motor.
E06Communication error(1) Harden the cable port.
(2) Replace the main cable of the upper and lower controller.
(3) Replace the electronic watch.
(4) Replace the controller.
EOCPower tube breakdown Explosion protection(1) Replace the controller.

Specifications

Here are the detailed specifications for the Superun Raceable Treadmill AS02R:

AttributeValue
Brand NameSuperun
Model NumberAS02
DisplayLCD Displays: Time, speed, distance and calories.
ConnectivityBluetooth connection available (Yes)
Apps CompatibilityPitPat compatible
Speed Range0.6-10 MPH / 1.0-16.0 KPH
Voltage220 V~240V
Running Belt Size16.53*44.09 inch / 420*1120 mm
Running Belt Width30-50cm
Maximum User Weight350 lbs / 158 kg
Unfolded Size54.72 * 24.13 * 42.32 inch / 1390 * 613 * 1075 mm
Folded Size54.13 * 24.13 * 7.87 inch / 1375 * 613 * 200 mm
Machine Weight (Net)95.02 lbs / 43.1 kg
Horse Power3.5HP / 2610 W
Adjustable SlopeYes, 6% adjustment range
With SpeakersNo
ScreenYes
FoldYes
Heart Rate TestWithout
Driving PowerElectric
FunctionMultifunctional
ApplicationHome Use Treadmill
Type of SportsStrength Training
Training SiteLegs

Workout Routines

Before commencing any exercise regimen, it is imperative that you consult your health care professional. Warm-up exercises enhance blood circulation, providing muscles with increased oxygenation, elevation in body temperature, and preparation for the physical exertion to follow. Each training session should initiate with a five to ten minutes stretch routine and light movements warm-up. The accompanying illustrations showcase various fundamental stretches.

The recommended approach is to undertake a warm-up session prior to executing your workout. For comprehensive warm-up benefits, repeat each stretch for three consecutive sets.

Warm-up

A warm-up exercise of 5-10 minutes is recommended before each workout.

Breathing

Do not hold your breath during the workout. Normally, when you are ready to restore your movements, breathe through your nose and exhale with your mouth. Breathing should be coordinated with your movements. If you find you're struggling to catch your breath, stop exercising until you can recover.

Frequency

Muscles in the same area should have 48 hours of rest, that is, the same area can be trained the next day.

Load

Depending on the individual physical condition of each person, this will determine the amount of training according to the principle of asymptotic load. Muscle soreness is normal at the beginning of training, as long as you continue the exercise, soreness can be eliminated.

Relax

Five minutes of restoring action should be taken after each exercise, especially when the foot muscles are stretched and relaxed to prevent long-term coagulation and maintain muscle elasticity.

Diet

In order to protect the digestive system, it's recommended not to train within 60 minutes of eating any meal. After training, it's recommended to eat within two hours to replenish your body's glycogen stores. During exercise, take care not to drink large amounts of water, so as to avoid increasing the burden on the heart and kidney.

Stretching Exercises

  1. **Stretch Down:** Bend your knees slightly with your body stretched down slowly, let your back and shoulders relax, and try to extend your hands to touch your toes. Hold for 10-15 seconds and take a break for a few seconds.
  2. **Hamstring Stretch:** Sit down and straighten one leg and place the other leg inward towards the thigh and snug on the inside of the straightened leg. In the meantime, try to touch the toes of your straightened leg with the hand at the same side. Hold for 10-15 seconds and take a break for a few seconds.
  3. **Calf and Achilles Tendon Stretches:** Place both hands against the wall while standing with one foot behind the other, keeping your back leg straight and both heels planted on the ground while leaning against the wall. Hold for 10-15 seconds and take a break for a few seconds.
  4. **Quadriceps Stretch:** Hold your body steady with your left hand holding against the wall and right hand reaching back to grab your right heel and pull it slowly towards your hips, until you feel the muscle tightness at the front side of your thigh. Hold for 10-15 seconds and take a break for a few seconds. Repeat several times for each leg.
  5. **Sartorius (muscle of inner thigh) Stretch:** Sit on the floor with your two feet holding against each other and your knees pointing to the opposite directions, grab your feet with your hands and pull them toward your groin. Hold for 10-15 seconds and take a break for a few seconds.

User Tips

  • Many users appreciate the easy setup of this treadmill. It can be unpacked and put into operation quickly.
  • The treadmill's folding design makes it convenient for storage and moving.
  • The PitPat app integration offers interactive training experiences, including outdoor scene simulations and AI coaches.
  • The 6% adjustable incline is a popular feature for burning more calories and simulating uphill running.
  • The quiet motor (less than 45dB) ensures you can exercise without disturbing others.
  • If you experience a loud noise, check the motor and running belt for any issues, as per the troubleshooting section.

Warranty and Support

Disclaimer

You should consult your physician, doctor, or other health care professional before starting or taking part in any of our workout guides. It is your responsibility to evaluate your own health before taking part or performing any physical activity you may see associated with us.

Always seek professional advice before changing your diet or starting any exercise program.

We are not liable for any injuries or damages that may occur when assembling or using this treadmill.

Users must be cautious when using the top speeds on this treadmill.

By reading this you assume full responsibility for any injuries or changes to your physical well-being. You waive all rights and release us of blame from any injuries or damages to property that may occur whilst following our advice.

This manual offers specific instructions on how to assemble and maintain your treadmill. Failure to follow these directions may result in your warranty being void.

Disposal of Waste Electrical and Electronic Equipment (WEEE)

The crossed-out wheeled bin symbol indicates that you are obliged by law to dispose of this equipment separately from unsorted municipal waste. If the equipment contains portable batteries, accumulators, or lamps that are not permanently installed, these must be removed before disposing of the product and be disposed of separately as waste portable batteries.

Owners of waste electrical and electronic equipment can return them to facilities for returning or collecting waste electrical and electronic equipment set up and provided by public-sector waste disposal authorities or with collection points installed by producers, retailers, or distant sellers to ensure correct disposal. For more information, refer to: https://e-schrott-entsorgen.org/

Owners of waste electrical and electronic equipment are responsible for deleting all personal data from the waste electrical and electronic equipment to be disposed of.

Contact Support

For any questions or support, you can contact us via email: treadmill@pitpatpower.com

If your device includes an activation warranty benefit, please follow the instructions on the quick operation card to activate the device before normal use.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.