Introduction
This manual provides detailed instructions for the setup, operation, and maintenance of your Beninca TO.GO 2WP fixed code remote control. This device is designed for controlling compatible Beninca garage doors and gates operating at a frequency of 433.92MHz.
Image: Front view of the Beninca TO.GO 2WP remote control.
Specifications
| Feature | Detail |
|---|---|
| Model | Beninca TO.GO 2WP |
| Frequency | 433.92MHz |
| Code Type | Fixed Code |
| Number of Buttons | 2 |
| Battery | Included |
| Dimensions (L x W x T) | 70mm x 40mm x 6mm |
| Weight | 0.035 kg |
| Origin | Mainland China |
| Certification | CE |
| Compatible Models | Beninca TO.GO 2WP, Beninca TO.GO 4WP |
Important: Access to your receiver/opener is required for programming. Please ensure you have this access before attempting to program the remote.
Image: Diagram showing the dimensions of the remote control.
Package Contents
- 1 x Beninca TO.GO 2WP Remote Control
- 1 x Battery (pre-installed)
- 1 x Keychain
Setup and Programming
Follow these steps to program your new Beninca TO.GO 2WP remote control.
Step 1: Clear the Programmer's History
- Press buttons A and B continuously until the LED flashes 3 times.
- Release button B (while continuing to press button A).
- Press button B slowly for 3 times. The LED will flash 3 times.
- Release button A. The history is now cleared.
Step 2: Programming Code from Original Transmitter
- Place the new remote control (programmer) as close as possible to your original Beninca transmitter.
- Press and hold button A on your original transmitter.
- While still holding button A on the original transmitter, press and hold button A on the new remote control (programmer).
- Continue holding both buttons until the LED on the new remote control blinks.
- Release both buttons. The code for button A is now programmed.
- Repeat the process for button B, if desired, using button B on both the original and new remote controls.
Button Functions:
- Button A: Lock / Open
- Button B: Unlock / Close
Image: Demonstrating pressing a button on the remote control.
Operation
Once programmed, your Beninca TO.GO 2WP remote control is ready for use.
- To activate your garage door or gate, simply press the corresponding programmed button (A or B) on the remote control.
- The LED indicator on the remote will light up when a button is pressed, indicating that a signal is being transmitted.
- Ensure you are within range of your receiver for successful operation.
Image: Remote control in use, opening a garage door.
Maintenance
Battery Replacement
The remote control comes with a pre-installed battery. If the remote's range decreases significantly or the LED indicator does not light up when a button is pressed, it may be time to replace the battery.
- Locate the battery compartment on the back of the remote control.
- Carefully open the compartment using a small screwdriver or coin.
- Remove the old battery and insert a new one, ensuring correct polarity.
- Close the battery compartment securely.
Care and Storage
- Keep the remote control dry and away from moisture.
- Avoid exposing the remote to extreme temperatures or direct sunlight for prolonged periods.
- Do not drop or subject the remote to strong impacts.
- Clean the remote with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
Troubleshooting
- Remote not programming:
- Ensure the new remote is placed as close as possible to the original transmitter during programming.
- Verify that the original transmitter is functioning correctly.
- Check the battery in the new remote. A low battery can prevent successful programming.
- Confirm that your receiver/opener is compatible with fixed code 433.92MHz remotes and that you have access to its programming function.
- Remote not working after programming:
- Re-attempt the programming steps carefully.
- Ensure the remote's history was cleared correctly before programming.
- Check the battery.
- Verify that the remote is within the operating range of your garage door/gate receiver.
- LED indicator not lighting up:
- The battery may be dead or low. Replace the battery.
- Ensure buttons are pressed firmly.
User Tips
No specific user tips are available from provided reviews or Q&A content at this time.
Warranty and Support
This product is manufactured by Shenzhen Scimagic Development Technology Co.Ltd.
For technical support or warranty inquiries, please refer to the contact information provided by your retailer or the manufacturer's official website.
Manufacturer Address: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.
The product is CE certified, indicating compliance with European health, safety, and environmental protection standards.
A user manual in PDF format is available for download: View User Manual (PDF)
Product Media
Product Overview Video
Video: A short demonstration of the Beninca TO.GO 2WP remote control, showcasing its physical appearance and button functionality.
Additional Product Images
