1. Introduction
The LAUNCH CR629 OBD II scanner is specifically designed to provide comprehensive diagnostics for your vehicle. It supports all 10 modes of OBD II test for a complete diagnosis, featuring a 3.5-inch TFT color display for clear data presentation. This tool allows users to read and clear Diagnostic Trouble Codes (DTCs), record, save, and playback live data in a graphic display. With built-in help menus and code definitions, diagnosing and repairing engine, ABS, and SRS related issues is made easier.
The CR629 can be updated via a memory card to ensure it always has the latest software version.
This tool is designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). EPA regulations require all 1996 and newer vehicles (cars and light trucks) sold in the United States to be OBD II compliant, covering American, Asian, and European vehicles. Some 1994 and 1995 gasoline vehicles may also be OBD II compliant; verify by checking the Vehicle Emissions Control Information (VECI) Label under the hood or by the radiator, which should state "OBD II Certified".

2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the test equipment, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep the test equipment dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test equipment, when necessary.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
3. Product Description
3.1 General Controls

| No. | Name | Notes |
|---|---|---|
| 1 | DB-15 DIAGNOSTIC CONNECTOR | Connects the tool to the vehicle's Data Link Connector (DLC). |
| 2 | USB PORT | Connects the tool to computer via USB cable for upgrade. |
| 3 | MEMORY CARD SLOT | Insert the memory card into it to read or write the data/file stored in the memory card. |
| 4 | ERASE BUTTON (F2) | Clears the diagnostic trouble codes. |
| 5 | I/M BUTTON (F3) | Quick access to I/M readiness function. Deletes the diagnostic record in the Print function module. |
| 6 | RETURN BUTTON | Returns to previous menu. |
| 7 | OK BUTTON | Confirms a selection (or action) from a MENU list. |
| 8 | NAVIGATION BUTTONS (UP/DOWN/LEFT/RIGHT) | Scrolls through menus, submenus, and screen data. |
| 9 | HELP BUTTON | Quick access to Help function. |
| 10 | DTC BUTTON (F1) | Reads the diagnostic trouble codes. |
| 11 | LED for different DTC types | Green (No Fault Code), Yellow (Pending Fault Code), Red (Permanent Fault Code) indicate engine system conditions. |
| 12 | LCD SCREEN | Displays test results. |
3.2 Accessories

The LAUNCH CR629 package typically includes:
- OBD II Scanner (CR629 Main Unit)
- Diagnostic Cable
- Memory Card
- Memory Card Adaptor
- Quick Start Guide
- USB cable (for upgrading online)
- User's Manual (this document)
4. Setup and Initial Use
4.1 Connection to Vehicle
- Turn the vehicle ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). This is usually located 12 inches from the center of the instrument panel (dash), under or around the driver's side. For some Asian and European vehicles, it might be behind the ashtray. Refer to your vehicle's service manual if you cannot find it.
- Plug the diagnostic cable of the CR629 tool into the vehicle's DLC. The cable connector is keyed and will only fit one way. If you encounter difficulty, rotate the connector 180 degrees and try again.
- Turn the ignition on. The engine can be off or running.
- The system will automatically turn on and navigate to the main menu screen.
CAUTION: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
4.2 Software Update and Registration
To ensure optimal performance and access to the latest vehicle data, it is recommended to register and update your CR629 scanner.
- Download Update Tool: Go to www.x431.com/CR629 to download and install the update tool on your computer (Windows XP, 7, 8, or 10).
- Note Serial Number and Register Code:
- Connect the USB cable to your CR629 and then to your computer.
- After the tool powers up, navigate to the "Help" icon on the main menu and press [OK].
- Select "Tool Information" and press [OK].
- Write down the displayed Serial Number and Register Code. These are crucial for registration.
- Register the Scanner:
- Launch the update tool on your computer.
- Enter your E-mail address and the Register Code obtained in the previous step. Click [Submit] to complete registration. For initial registration, this process is required. Subsequent updates will not require re-registration.
- Copy Update Package to Memory Card:
- Install the memory card from the CR629 into the supplied memory card adaptor and insert it into your computer's USB port.
- Reopen the update tool, select the desired updates or "Select All", and click [Download] to begin downloading the update package to the memory card.
- Reinsert Memory Card and Update:
- Once the download is complete, reinsert the memory card into the CR629 tool.
- Power up the tool via the USB cable.
- The tool will automatically verify the files and begin the update process. A green progress bar will appear. Be patient until the update is finished.
5. Operating Instructions
5.1 Main Menu Overview
The main menu provides access to the following function modules:
| Module | Description |
|---|---|
| ABS/SRS | Accesses Anti-Lock Braking System (ABS) and Supplemental Restraint System (SRS) for deep diagnostics, including Active Test, Version Info, Read/Clear DTCs, and Live Data. |
| OBD II | Performs full OBD2 functions to check for DTCs, isolate MIL causes, check monitor status, verify repairs, and other emission-related services. |
| SERVICE | Performs common repair and maintenance items such as Oil Lamp Reset, Steering Angle Sensor (SAS) Reset, and Battery Management System (BMS) Reset. |
| REVIEW | Enables review and deletion of recorded DTCs, data streams, and freeze frame data. |
| LOOKUP | Retrieves desired DTCs and displays their detailed definitions. |
| Prints diagnostic records saved during a diagnostic session (requires USB connection to PC). | |
| HELP | Provides general knowledge about DLC location, tool information, and OBD. |
| SETUP | Displays the tool setup menu for language, unit of measure, beeper, and record mode settings. |
5.2 OBDII/EOBD Diagnosing
After connecting the tool to the vehicle's DLC, select [OBD II] from the main menu. The tool will automatically detect the communication protocol and establish a link, then display the Monitor Status.
Note: A PROTOCOL is a set of rules for data transmission. The CR629 supports ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW, and CAN.
5.2.1 Read Codes
This function allows you to view Diagnostic Trouble Codes (DTCs) retrieved from the vehicle's on-board computer.
Note: Never replace a part based solely on the DTC definition. Always refer to the vehicle's service manual for proper testing procedures.
Select [Read Codes] from the Diagnostic Menu. The system will automatically read SAE-standard DTCs. If manufacturer-specific codes are found, you may be prompted to select the vehicle manufacturer manually.

5.2.2 Erase Codes
This function clears DTCs from the vehicle's computer. When erasing DTCs, "Freeze Frame" data is also erased, but "Permanent" DTCs are NOT erased.
IMPORTANT: If you plan to take the vehicle to a Service Center, DO NOT erase codes as this removes valuable diagnostic information. Ensure the ignition is ON and the engine is OFF before erasing codes.
Note: Erasing DTCs resets I/M Readiness Monitors to "Not Completed". An OBD II Drive Cycle must be performed to reset them to "Completed".
5.2.3 I/M Readiness
Indicates whether emission-related systems are operating properly and are ready for Inspection and Maintenance testing. "N/A" means not available, "INC" means incomplete/not ready, "OK" means completed/monitor OK.
5.2.4 Data Stream
Retrieves and displays live data and parameters from the vehicle's ECU. This data can be viewed graphically for more intuitive analysis.
5.2.5 View Freeze Frame
Records vehicle conditions at the moment an emission-related fault occurs, providing a snapshot of operating parameters.
5.2.6 O2 Sensor Test
Retrieves and displays O2 sensor monitor test results for recently completed tests.
5.2.7 On-board Monitor Test
Reads results of on-board diagnostic monitoring tests for specific components/systems.
5.2.8 EVAP System Test
Initiates a leak test for the vehicle's EVAP system. The tool signals the vehicle's computer to start the test; the vehicle manufacturer determines the criteria for stopping it.
5.2.9 Vehicle Info
Retrieves information from the vehicle's on-board computer, including VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
5.3 System Diagnosing (ABS & SRS)
This function is specifically designed to diagnose Anti-lock Brake System (ABS) and Supplemental Restraint System (SRS).

Note: Ensure the diagnostic program for your specific vehicle model is installed. Diagnostic menus may vary by manufacturer.
To diagnose, select [ABS/SRS] from the main menu. You can choose between Automatic scan mode (tool scans automatically) or Manual Select (you manually choose the system). Functions include:
- Read Version Info: Identifies specific information for the control unit.
- Read / Clear DTCs: Reads and clears diagnostic trouble codes.
- Read Live Data: Retrieves real-time data stream for analysis.
- Active Test: Sends commands to vehicle control modules to test devices.
5.4 Service Functions
The CR629 offers several service functions for common maintenance tasks:

- Oil Reset: Resets the oil service light after an oil change.
- SAS Reset (Steering Angle Sensor Reset): Recalibrates the steering angle sensor, important after steering system changes, to maintain proper Electronic Stability Control (ESC) function.
- BMS Reset (Battery Management System Reset): Clears unhealthy status memories of a replaced battery in the ECU, allowing the ECU to recognize and record the new battery's status.
Service resets can be performed via Manual Reset (follow on-screen instructions) or Auto Reset (tool sends commands to ECU).
5.5 DTC Lookup
This function allows you to quickly retrieve diagnostic trouble codes from the DTC library and view their detailed definitions. Select [Lookup] from the main menu, input the DTC (e.g., P0000), and press [OK] to see the definition.
6. Maintenance
6.1 Software Updates
Regular software updates ensure your CR629 has the latest vehicle compatibility and diagnostic features. Refer to section 4.2 "Software Update and Registration" for detailed instructions on how to update your device.
6.2 Cleaning and Storage
Keep the test equipment dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test equipment, when necessary. Store the device in a safe, dry place within the recommended storage temperature range of -4°F~158°F (-20°C ~70°C) at 60% relative humidity.
7. Troubleshooting (FAQ)
Here are some frequently asked questions and answers related to the CR629 tool:
- Question: System halts when reading data stream. What is the reason?
Answer: It may be caused by a slackened connector. Please turn off the tool, firmly connect the connector, and switch it on again. - Question: Screen of main unit flashes at engine ignition start.
Answer: Caused by electromagnetic disturbing, and this is normal phenomenon. - Question: There is no response when communicating with on-board computer.
Answer: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature. - Question: Why are there so many fault codes?
Answer: Usually, it's caused by poor connection or fault circuit grounding. - Question: What to do if the tool fails to boot up?
Answer: Please connect the tool to the USB port of a computer to fix the firmware. - Question: Is this scanner compatible with a 2004 Suzuki Ignis?
Answer: The CR629 supports OBD2 functions for US-based cars from 1996, EU-based cars from 2000, and Asia-based cars from 2008. For a 2004 Suzuki Ignis, it may support basic OBD2 functions if the vehicle is OBD2 compliant. Check your vehicle's VECI label for "OBD II Certified". - Question: Does it support the bleeding of the ABS control unit for a 2013 Renault Twingo 2?
Answer: The CR629 supports ABS & SRS diagnoses and Active Tests. Specific advanced functions like ABS bleeding may vary by vehicle model and year. Please refer to the vehicle's service manual or contact customer support for specific compatibility.
8. Specifications

| Parameter | Specifications |
|---|---|
| Screen | 3.5" LCD display with a resolution of 320*480 pixels |
| OBD II Interface Input Voltage | 9V ~ 18V |
| Operating Temperature | 32°F ~ 122°F (0°C ~ 50°C) |
| Storage Temperature | -4°F ~ 158°F (-20°C ~ 70°C) @ RH60% |
| Size | 114.1 x 215.0 x 34.5 mm (4.49 x 8.46 x 1.36 inches) |
| Net Weight | ~500g (17.64 oz) |
| Free Update Period | Lifetime |
| Software Update | Yes |
| Wireless Support | No |
| Battery Included | No |
| Languages | German, Italian, Japanese, English, Spanish, French, Portuguese, Russian |
| Certification | RoHS, CE, FCC |

9. Warranty and Support
9.1 Warranty Information
LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is limited to persons who purchase LAUNCH products for resale or use in the ordinary course of the buyer's business.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
9.2 Customer Service
If you have any questions on the operation of the unit, please contact your local dealer or LAUNCH TECH. CO., LTD:
- Tel: +86-755-84527891
- E-mail: overseas.service@cnlaunch.com
10. User Tips
- Vehicle Compatibility: While the CR629 supports a wide range of vehicles, always verify your specific car model and year against the supported vehicle list or check your vehicle's VECI label for OBD II compliance, especially for older models.
- Software Updates are Key: Take advantage of the lifetime free updates. Regularly updating your scanner ensures you have the latest diagnostic capabilities and vehicle data, which can be crucial for newer car models or specific functions.
- DTC Lookup Efficiency: Use the built-in DTC Lookup function to quickly understand fault codes. This can save significant time compared to searching online.
- Data Recording: Utilize the data recording and playback features to capture intermittent issues. This can be invaluable for diagnosing problems that don't occur consistently.
- Printing Reports: For detailed record-keeping or sharing diagnostic results with a mechanic, use the PC printing function. This provides a clear, organized report of your vehicle's status.