1. Introduction
Thank you for choosing the AISET Digital Panel Meter NH-400/NH-406Z. This device is a high-precision digital display instrument designed for industrial control applications, specifically for measuring and displaying voltage signals. The NH-406Z variant accepts a 0-10V input and displays values in the range of 0-75.0. This manual provides essential information for the safe and effective installation, operation, and maintenance of your panel meter.
2. Safety Information
Please read and understand all safety instructions before installing or operating the device. Failure to follow these instructions may result in injury or damage to the equipment.
- Ensure power is disconnected before making any wiring connections.
- Only qualified personnel should perform installation and maintenance.
- Verify correct voltage and current ratings before connecting power.
- Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
- Avoid touching internal components when the device is powered.
- Clean the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
3. Package Contents
Upon unpacking, please verify that all items are present and undamaged:
- 1 x AISET Digital Panel Meter (NH-400/NH-406Z)
- 1 x Set of Mounting Brackets
- 1 x User Manual (small printed version, refer to this digital manual for comprehensive details)
4. Product Overview
4.1 Front Panel
The front panel features the digital display, alarm indicators, and control buttons.
- Digital Display: 4-digit LED display for measured values.
- ALM1 Indicator: Illuminates when Alarm 1 condition is met.
- ALM2 Indicator: Illuminates when Alarm 2 condition is met.
- Buttons:
- Reset/Enter Button: Used to reset certain functions or confirm settings.
- Left/Shift Button: Used to move cursor or shift digits during setting.
- Down Button: Used to decrease values or navigate menus.
- Up Button: Used to increase values or navigate menus.
4.2 Rear Panel and Terminal Block
The rear panel houses the terminal block for power and signal connections.
5. Specifications
| Parameter | Specification |
|---|---|
| Model | NH-400 / NH-406Z |
| Input Signal | 0-10V |
| Display Range | 0-75.0 |
| Power Supply | 100-240VAC, 50Hz, 5VA |
| Weight | Approx. 0.3 kg |
| Origin | Mainland China |
| Customization | No |
6. Installation
6.1 Panel Mounting
The NH-400/NH-406Z is designed for panel mounting. Follow these steps:
- Cut a rectangular opening in your control panel according to the meter's dimensions (refer to product drawings for exact cutout size, typically standard for this form factor).
- Insert the meter into the panel opening from the front.
- Attach the provided mounting brackets to the sides of the meter from the rear of the panel.
- Tighten the screws on the mounting brackets to secure the meter firmly in place. Do not overtighten.
6.2 Wiring Diagram
Ensure all power is OFF before making any wiring connections. Refer to the diagram below and the terminal labels on the device.
| Terminal No. | Function | Description |
|---|---|---|
| 1, 2 | Power Supply | Connect to 100-240VAC, 50Hz power source. |
| 3, 4 | ALM1 Output | Alarm 1 output terminals (functionality depends on configuration). |
| 5, 6 | ALM2 Output | Alarm 2 output terminals (functionality depends on configuration). |
| 7, 8 | Input (0-10V) | Connect your 0-10V analog input signal here. |
7. Operation
Once properly installed and powered on, the meter will display the measured input value. The basic operation involves navigating menus and setting parameters using the front panel buttons.
- Power On: After connecting the power supply, the meter will power on and typically display the current input value.
- Viewing Measured Value: The primary display shows the real-time input voltage, scaled to the 0-75.0 range.
- Accessing Settings: Press and hold the 'Reset/Enter' button to enter the parameter setting mode. Use the 'Up' and 'Down' buttons to navigate through parameters and the 'Left/Shift' button to select digits or move between settings.
- Adjusting Parameters: When a parameter is selected, use the 'Up' and 'Down' buttons to change its value. Press 'Reset/Enter' to confirm and save the setting.
- Alarm Indicators: ALM1 and ALM2 indicators will light up when the measured value exceeds or falls below the configured alarm setpoints.
Note: Detailed parameter settings (e.g., alarm setpoints, scaling, decimal point position) are typically covered in the full manufacturer's manual. Please consult the specific documentation for advanced configuration.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Meter does not power on. | No power supply or incorrect wiring. | Check power connections (100-240VAC) and ensure power is supplied. |
| Display shows '----' or erratic readings. | Input signal issue or incorrect wiring. | Verify 0-10V input signal is connected correctly to terminals 7 and 8. Check signal source. |
| Incorrect display value. | Scaling or calibration error. | Refer to the full manual for calibration procedures. Ensure the input signal is within the 0-10V range. |
| Alarm indicators (ALM1/ALM2) not working as expected. | Alarm setpoints not configured or incorrect wiring. | Check alarm setpoints in the meter's settings. Verify wiring to ALM1/ALM2 terminals. |
9. User Tips
- Easy Installation: Users have reported that the meter is straightforward to install and works as expected once connected.
- Voltage Measurement: This model is specifically designed for voltage measurement with a 0-10V input, making it suitable for various industrial voltage monitoring tasks.
10. Maintenance
- Cleaning: Keep the front panel clean using a soft, dry cloth. Do not use harsh chemicals or abrasive materials that could damage the display or casing.
- Storage: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified operating temperature range.
- Inspection: Periodically inspect wiring connections for tightness and signs of wear or corrosion.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.