1. Introduction
The HGLRC SPECTER 90A ESC is a high-performance Electronic Speed Controller designed for RC FPV drones. It features a robust double-sided fully wrapped CNC shell for efficient heat dissipation and protection against debris. With a dual MOS parallel solution, it supports a continuous current of 90A and a peak current of 100A. The ESC incorporates a high-performance ARM 32-bit Cortex core MCU (STM32G071) operating at up to 64MHz and supports BL32 ESC telemetry for real-time monitoring of critical parameters.
2. Product Features
- Robust Construction: Double-sided fully wrapped CNC shell for efficient heat dissipation and protection from foreign matter.
- High Current Capability: Dual MOS parallel solution supporting 90A continuous current and up to 100A peak current.
- Advanced Telemetry: Supports BL32 ESC telemetry for real-time monitoring of ESC temperature, current, and motor speed.
- Powerful MCU: High-performance ARM 32-bit Cortex core MCU (STM32G071) with an operating frequency up to 64MHz.
- Wide Voltage Input: Supports 2-8S working voltage.
- Flexible Input Voltage Selection: Flight control input voltage can be selected as 12V or BAT input, ensuring compatibility with most flight controllers.
- Integrated Signal Collection: Signals from the single ESC are uniformly collected on the GH1.25 interface for efficient and simple assembly with flight controllers.
- Temperature Protection: Built-in temperature protection for enhanced reliability.
- Drive Signal Support: Compatible with Dshot150, Dshot300, Dshot600, Oneshot, and Multishot drive signals.
3. Specifications
| Parameter | Value |
|---|---|
| Product Name | HGLRC Specter 90A ESC |
| Frame Size | 39mm x 19.6mm x 8.34mm |
| Weight | 13.9g |
| Firmware Version | BLheli32 32.9 |
| MCU | STM32G071 |
| Continuous Current | 90A |
| Instantaneous Peak Current | 100A |
| Working Voltage | 2-8S |
| Temperature Protection | Supported |
| ESC Telemetry | Supported |
| Drive Signal Support | Dshot150, Dshot300, Dshot600, Oneshot, Multishot, PWM |
| Material | Composite Material |
| For Vehicle Type | Airplanes (FPV Drones) |
| Recommended Age | 14+ years |
Image: Dimensions of the HGLRC SPECTER 90A ESC (39mm x 19.6mm x 8.34mm) and its total package weight (71.8g) and single ESC weight (13.9g).
4. Package Contents
Please verify that all items listed below are included in your package:
- 1x HGLRC SPECTER 90A ESC
- 1x 50V 470UF Solid Capacitor
- 1x Red Heat Shrink Tubing
- 1x Black Heat Shrink Tubing
- 1x Black 12AWG Power Cord (20cm)
- 1x Black, Green, and Yellow 30AWG Silicone Wire (20cm)
Image: Visual representation of the HGLRC SPECTER 90A ESC and its included accessories.
5. Setup & Installation
5.1 Wiring Diagram
Refer to the diagram below for proper connection of the ESC to your flight controller and motors. Ensure all connections are secure and correctly oriented.
Image: Detailed wiring diagram showing connections between four HGLRC SPECTER 90A ESCs, a flight controller, and a drone battery.
5.2 Interface Definition
Understand the function of each pin on the ESC for correct connection:
Image: Diagram illustrating the interface definitions of the HGLRC SPECTER 90A ESC.
- BAT: Positive pole for battery connection.
- GND: Negative pole (ground).
- TX: ESC telemetry feedback, typically connected to the flight control RX pin.
- PWM: Connected to the flight control motor output signal or PWM signal.
- GND: Negative pole (ground).
- Motor Pins: Three pins for connecting to the motor.
5.3 Input Voltage Selection
The flight control input voltage can be configured as either 12V input or BAT (battery voltage) input. This feature ensures broad compatibility with various flight controllers.
Image: Close-up of the ESC board showing the pads for selecting 12V or BAT input voltage.
5.4 GH1.25 Interface for Signal Collection
The ESC is designed to collect all signals uniformly on a GH1.25 interface. This allows for direct plug-in connection to compatible flight controllers, simplifying assembly and improving efficiency.
Image: Close-up of the GH1.25 interface on the ESC for streamlined signal connection.
6. Operation
The HGLRC SPECTER 90A ESC supports various digital and throttle signals, including Dshot150, Dshot300, Dshot600, Oneshot, Multishot, and PWM. Configuration of these signals and motor direction is typically done through your flight controller's software (e.g., Betaflight, ArduPilot).
Image: Screenshot of a flight controller configuration software (e.g., Betaflight) motor tab, illustrating options for selecting digital (Dshot) and throttle (Oneshot, Multishot, PWM) signals. It also displays a critical safety warning regarding propeller removal during motor testing.
6.1 BL32 ESC Telemetry
The ESC supports BL32 telemetry, allowing for real-time monitoring of crucial data such as ESC temperature, current draw, and motor RPM. This information can be displayed on your FPV OSD (On-Screen Display) or logged by your flight controller, aiding in performance tuning and diagnostics.
Image: The HGLRC SPECTER 90A ESC mounted on a drone arm, demonstrating its use and the capability for BL32 telemetry.
7. Maintenance
- Regular Inspection: Periodically inspect the ESC for any signs of physical damage, loose connections, or debris accumulation.
- Cleaning: Keep the ESC clean. The CNC shell helps prevent debris ingress, but gentle cleaning with a soft brush or compressed air can remove any surface dust.
- Heat Management: Ensure adequate airflow around the ESC, especially during high-current operations, to maximize the efficiency of the CNC shell's heat dissipation.
- Firmware Updates: Check the HGLRC official website or BLHeli_32 resources for any available firmware updates. Follow official instructions carefully when updating firmware.
8. Troubleshooting
- No Motor Spin/Incorrect Direction:
- Verify all motor and signal connections are secure and correctly wired according to the diagram.
- Check motor direction in your flight controller software. Adjust if necessary.
- Ensure the correct drive signal (Dshot, Oneshot, Multishot, PWM) is selected in your flight controller software and matches the ESC's capabilities.
- ESC Overheating:
- Ensure proper airflow.
- Check for motor issues (e.g., binding, incorrect KV for propeller size) that might cause excessive current draw.
- Verify that the ESC is rated appropriately for your motor and propeller combination.
- Telemetry Issues:
- Confirm the TX pin of the ESC is correctly connected to the RX pin of your flight controller.
- Ensure telemetry is enabled and configured correctly in your flight controller software.
- General Malfunction:
- Inspect for any visible damage to the ESC or wiring.
- Ensure the input voltage is within the 2-8S range.
- Consider reflashing the ESC firmware if other solutions fail.
8.1 Safety Warning for Motor Testing
WARNING: Serious risk of injury! Always remove all propellers from your drone before performing any motor testing or configuration in software. Motors can spin up unexpectedly when armed or when sliders are manipulated in the software. Ensure you understand the risks and take all necessary precautions, including enabling motor control and arming, and disabling Runaway Takeoff Prevention in your flight controller software during testing.
9. User Tips
- Capacitor Installation: Always install the included 50V 470UF solid capacitor as close to the ESC's power input as possible to help filter voltage spikes and protect the ESC.
- Wire Management: Use the provided heat shrink tubing and silicone wires for neat and secure installations. Proper wire management reduces the risk of shorts and interference.
- Firmware Compatibility: While the ESC comes with BLheli32 32.9, always ensure compatibility with your flight controller's firmware version for optimal performance.
- Initial Setup: During initial setup, perform motor direction tests with propellers removed to prevent accidents.
10. Warranty & Support
For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. Specific warranty terms and conditions may vary and are typically provided by the point of purchase.