1. Introduction
Thank you for purchasing the Baofeng UV-K61 Pro Walkie Talkie. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communications. To ensure maximum performance and safe operation, please read this manual carefully before use.
1.1 Main Features
- Multi-Band Frequency Range: FM radio 65-108 MHz (RX), AM aviation 108-136MHz (RX), VHF1 136-174MHz (TX&RX), VHF2 200-219.995MHz (RX), VHF3 220-259.995MHz (TX&RX), Police 350-390MHz (TX&RX), UHF1 400-480MHz (TX&RX), UHF2 480-599.995MHz (RX).
- 1.54' TFT Large Screen: Provides clear display of all information.
- Wireless Copy Frequency: Two simple steps, one-button automatic frequency matching.
- NOAA Weather Reception: Detects and predicts extreme weather events, provides long-term forecasts and real-time meteorological data.
- 640 Memory Channels: More channel reserves for convenient and faster one-touch intercom.
- Type-C Charging & Base Charging: Flexible charging options including power bank and car charging.
- DTMF Encoder & Manual Dial: Supports 2 Tone, 5 Tone, BDC1200 analog signaling.
- LED Flashlight: Built-in powerful LED spotlight for emergency and night use.
- VOX (Voice Activated Transmit): Hands-free communication.
- Dual Watch / Dual Reception: Monitor two channels simultaneously.
- Programmable: PC programmable with customizable display illumination, keypad beep, power-on message, and password.
- High Capacity Lithium-Ion Battery: 2600mAh for long standby time.

1.2 Content of the Packaging
The standard package includes:
- 1 x Radio
- 1 x Li-Ion Battery Pack (2600mAh)
- 1 x Antenna
- 1 x Fast Desktop Charger
- 1 x Wall Adaptor
- 1 x Belt Clip
- 1 x Lanyard
- 1 x User Manual
- 1 x Box

1.3 Regulations and Safety Warnings
EU Regulatory Conformance: The product complies with essential requirements and relevant provisions of Directive 2014/53/EU and other applicable EU regulations (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). It can operate under 2000m.
WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU. This information is applicable to EU countries only.
ATTENTION! When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. Use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.
ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.
PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.
RF Exposure Compliance and Control Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions for RF Exposure:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
- Keep the radio unit at least 2.5cm away from the face. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
Precautions for Portable Terminals:
Operating Prohibitions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
2. Setup
2.1 Installing/Removing the Antenna
- Screw the antenna clockwise into the connector on the top of the radio until it is firmly seated.
- To remove, unscrew the antenna counter-clockwise.
2.2 Installing the Belt Clip
- Align the grooves of the belt clip with those of the radio and push down until you hear a click.
- To remove the clip, use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip upward and away from the radio.
2.3 Installing/Removing the Battery Pack
Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.
To Remove the Battery Pack:
Press the battery release above the battery pack, as you slide the battery downward.
2.4 Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
3. Charging the Battery
The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before its first use or after extended storage.
3.1 Precautions for Batteries
Charging Prohibitions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres.
- Do not charge your battery if it is wet. Dry it with a soft, clean cloth prior to charging.
- Do not charge your battery if it is suffering deformation, leakage, or overheating.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge is prohibited as it may shorten battery life.
Maintenance Instructions:
- Accumulated dust on the charging connector may affect normal charging. Wipe it with a clean, dry cloth regularly.
- Charge the battery under 5°C~40°C. Violation may cause battery life reduction or leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging until fully charged.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight or other heating sources.
- Do not squeeze, penetrate the battery, or remove its housing.
WARNING! If keys, ornamental chain, or other electric metals contact the battery terminal, the battery may be damaged or injure a human. Short-circuited battery terminals generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.
3.2 How to Charge
- Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange, indicating it's ready to charge.
- Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light turns red, indicating charging has begun.
- A full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete.
Note: If the radio is powered on during charging, the indicator lamp may not turn green to show full charge. The radio consumes energy when powered on, preventing the charger from detecting the correct battery voltage. For accurate indication, charge with the radio powered off.
3.3 LED Indicator Status
| Status | LED Indication |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble (e.g., battery too warm, short-circuited) | Red blinks fast for a long time |
3.4 How to Store the Battery
- Store the battery at approximately 80% discharged.
- Keep it in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
3.5 Using the Type-C USB Charger
The Type-C USB port allows convenient charging of your Li-ion battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet, power bank, or laptop.
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will move to indicate charging.
Note: It is recommended to power OFF your radio while charging. If powered ON, you may not be able to transmit if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

4. Basic Operations
4.1 Radio Overview: Buttons and Controls

- Antenna
- LED Flashlight
- Power/Volume knob
- Status LED
- LCD Screen
- PTT - Push to talk
- SK1-Programmable key (flashlight/alarm switch)
- A/B Select Key
- Accessory jack
- Type-C charging indicator
- V/M-VFO/MR mode key
- Up Key
- Down Key
- MENU Key
- Unlock Key
- Color LCD
- Speaker
- Microphone
- Monitor Key
- FM Key
- Back Clip
- Type-C Charging Port
- Keypad
4.2 LCD Display Icons
| Icon | Description | Icon | Description |
|---|---|---|---|
| Mxxx | Memory channel | DW | Dual watch enabled |
| VFO | Frequency Mode | TX | Transmitting |
| VOX | VOX enabled | RX | Receiving |
| CTC | CTCSS enabled | R | Reverse function enabled |
| DCS | DCS enabled | ▶ | Indicates active band or channel |
| N | Narrowband enabled | +/- | Frequency shift direction if enabled in VFO |
| H/L | Transmit power level indicator (High/Low) | Battery level indicator | |
| Squelch Open/Close Indicator |
4.3 Status Indications (LED)
The status LED indicates the radio's current state:
- Constant Red: Transmitting.
- Constant Green: Receiving.
- Off: Standby.
4.4 Main Keypad Controls
- V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode: CH/FREQ/NAME.
- A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/Signal Wait/Dual Watch off modes.
- One-Touch Search Key: Short press to enter One-Touch search key.
- EXIT: Short press to return to menu or previous menu. Press and hold to enter frequency sweep mode.
- *: Long press to lock or unlock the keypad.
- #z: Short press to enter DTMF dial. Press and hold to scan on and scan off.
- 0[space]: Press and hold to enter weather switch to select weather channel.
4.5 Programmed Keys (SK1, SK2)
The [SK1] and [SK2] keys can be programmed with different functions via the radio Menu (48/49/50 PF1 Press/PF1 LongPre/PF2 Press).
| Function | Description |
|---|---|
| None | No function |
| Torch On/Off | Quick switch torch |
| Power Select | Quickly switch between high, low transmit power |
| Scan On/Off | Quickly switch scanning function on or off |
| VOX On/Off | Quickly switch on/off VOX function |
| Alarm on/off | Quickly establishes an emergency call |
| Radio on/off | Quickly switch on or off the FM radio function |
4.6 Power On/Off the Radio
To turn the unit on, simply rotate the Volume/Power knob clockwise until you hear a "click". The display will show a frequency or channel. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode". To turn off, rotate the Volume/Power knob counter-clockwise until you hear a "click".
Note: If a power-on password is set, you need to enter the correct password. (Menu >>37 Power-on PWD)
4.7 Adjusting the Volume
Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far, as it may inadvertently turn your radio off.
4.8 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel. Press and hold [A/B] key to quickly switch Double Wait/Signal Wait.
4.9 VFO/Channel Switch
Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display. In channel mode (MR), the channel number will be displayed on the left. In frequency mode (VFO), 'VFO' will be displayed on the left. In MR mode, press and hold [V/M] key to switch the frequency, channel, and name display mode of the channel.
4.10 Frequency (VFO) Mode
In Frequency (VFO) mode, you can navigate up and down the band using the Up/Down keys, which will increment or decrement your frequency according to the frequency step you've set. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
Example: Entering 436.61250 MHz on display A
- In standby mode, press [V/M] key to switch to VFO mode.
- Enter [4][3][6][6][1][2][5] [0] on the numeric keypad.
WARNING! Transmitting on unauthorized frequencies is illegal and may lead to prosecution. The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to VFO mode and allows manual input. Prohibit use in channel mode.
4.11 Channel (MR) Mode and Channel Selection
Channel (MR) mode is practical for everyday use, while Frequency (VFO) mode is useful for experimentation and programming channels. To switch between VFO and Channel mode, press [V/M] key.
Channel Selection:
- Press the Up/Down navigation key to select the channel.
- Input the channel numbers by the keyboard (e.g., [0][1][2] for channel 12).
If the voice prompt function is enabled, the corresponding channel will be broadcast by voice.
4.12 Making a Call
Note: Press the [A/B] key to switch the main channel if two are displayed. In standby mode, press [V/M] key to switch between VFO and MR mode.
Channel Mode Call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on.
Frequency Mode Call: Press [V/M] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on.
Receive a Call: Release the [PTT] key. When receiving a call, the green LED will be on.
Note: For best reception volume, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.
4.13 Using the Flashlight
Press the [SK1] key once to turn on the high-intensity LED flashlight (Always On mode). Press [SK1] again for Strobe Light (emergency mode). Press [SK1] a third time to turn off the light.

4.14 Emergency Alert
To activate the emergency alert, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] key to exit. WARNING: Only use in actual emergencies.
4.15 FM Radio
The frequency range for listening to the radio is 65-108MHz.
- In frequency or channel mode, press [SK2] key to turn on the radio.
- Select the desired radio frequency with the Up/Down keys or input the frequency. Alternatively, press #z to automatically search for a radio station.
- Press [SK2] key to exit FM radio.
Note: While listening to the radio, if an A/B receiving signal is detected, the radio will automatically switch to that frequency/channel for normal transmitting and receiving. It will switch back to FM radio mode when the signal disappears.
4.16 Monitor
In standby, press and hold the [SK2] key to enter Monitor. This function allows monitoring weak signals or signals with matched carrier but weak signaling. Release [SK2] to turn off the speakers and return to standby. If no signal, it will emit noise when [SK2] is pressed.
4.17 Keypad Lock
The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the * key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds via the menu.
4.18 Frequency Reversal
A short momentary press of the * key enables the reverse function, allowing you to reverse your transmit and receive frequencies. This is indicated by an 'R' in the top row of the LCD, next to the +/- for offset direction.
4.19 TX Repeaters Tone
Press [PTT] + [SK2] key to send a 1750Hz repeaters tone. This is useful for communications through repeaters. This function works even if the keypad lock is enabled.
4.20 One Touch Frequency Search
- Press and hold the One-Touch Search key. The screen will display “SEARCH SWEEK...”. The radio will act as a receiver.
- If the unit receives an effective frequency, it will display the received frequency. If CTCSS or DCS is present, its value will be displayed; otherwise, NONE.
- Press the [MENU] key to save the Search frequency and CTCSS or DCS to a channel.
Note: During frequency search, press the #z key to switch between UHF or VHF bands.
4.21 Weather Radio/Scan Weather Channel (NOAA)
Your radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 channels.
- To turn on NOAA Weather Scan, press the [OSQL] key for 3 seconds. The radio will go to Weather band mode.
- Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding #z again will stop the scan.
- After stopping NOAA weather scan, you can manually select the weather channel by pressing the Up/Down key.
- To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Weather Channel Frequencies:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
5. Advanced Features
5.1 Working the Menu System
The menu system allows customization of various radio settings.
Basic Use with Arrow Keys:
- Press [MENU] key to enter the menu.
- Use the Up/Down keys to navigate between menu items.
- Press [MENU] again to select the desired menu item.
- Use the Up/Down keys to select the desired parameter.
- To confirm your selection, press [MENU] to save and return to the main menu. To cancel changes, press [EXIT] to reset and exit.
- To exit the menu at any time, press [EXIT] key.
Using Shortcuts:
Each menu item has a numerical value for direct access. The ten most common functions are at the top.
- Press [MENU] key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- Press [MENU] key to enter the menu item.
- For parameters, use arrow keys or the numerical keypad for short-cut code.
- To confirm, press [MENU] to save and return to the main menu.
5.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited while scanning.
To enable the scanner, press and hold the #z key for about two seconds. Press and hold the #z key again to exit scanning mode.
5.2.1 Scanning Modes
The scanner can be configured for Time, Carrier, or Search operation.
Setting Scanner Mode:
- Press [MENU] key.
- Enter 19 on the numeric keypad for scanner mode.
- Press [MENU] key to select.
- Use the Up/Down keys to select scanning mode (TO, CO, or SE).
- Press [MENU] key to confirm and save.
- Press [EXIT] key to exit.
- Time Operation (TO): Scanner stops on signal, resumes after a preset timeout.
- Carrier Operation (CO): Scanner stops on signal, resumes after signal disappears.
- Search Operation (SE): Scanner stops on signal. To resume, press and hold the #z key.
5.2.2 Frequency Scanning
In frequency mode, press #z key for more than 2 seconds. The radio will scan according to the set frequency step. Change scanning direction with Up/Down keys. Press #z key to stop.
5.2.3 Channel Scanning
In channels mode, press #z key for more than 2 seconds. The radio will scan according to the channels you set. Change scanning direction with Up/Down keys. Press #z key to stop.
5.2.4 Scan CTCSS
Scans frequencies with CTCSS tone enabled.
- In standby mode, press [MENU] [1][6]. "Scan CTCSS" will appear.
- Press [MENU] key to start scanning CTCSS tones.
Note: Cannot be activated in Channel mode. Scan starts only when the receiving band detects a signal.
5.2.5 Scan DCS
Scans frequencies with DCS code enabled.
- In standby mode, press [MENU] [1][7]. The display will show "Scan DCS".
- Press [MENU] key to start scanning DCS codes.
Note: Cannot be activated in Channel mode. Scan starts only when the receiving band detects a signal.
5.3 Manual Programming (Channels Memory)
The radio features 999 memory channels, each capable of storing receive/transmit frequencies, power, signaling, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.
Frequency Mode (VFO) vs. Channel Mode (MR): VFO is for temporary assignments or quick programming. MR is for selecting preprogrammed channels.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone (New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), TX CTCSS tone 123.0)
- Press [EXIT] to switch between menus.
- Press [V/M] key to set the radio to VFO mode.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes prior data in channel 10)
- [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
- Enter RX frequency (e.g., 43255000).
- [MENU] [1][3] [MENU] [1][0] [MENU] --> [EXIT] (Enters desired channel 10, RX added)
- Enter TX frequency (e.g., 43755000).
- [MENU] [1][3] [MENU] [1][0] [MENU] --> [EXIT] (Enters same channel 10, TX added)
- Press [V/M] key to return to MR mode.
Example 2: Programming a Simplex Channel with CTCSS Tone (New memory in Channel 10: RX = 432.6625 MHz, TX CTCSS tone 123.0)
- Press [EXIT] to switch between menus.
- Press [V/M] key to set the radio to VFO mode.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes prior data in channel 10)
- [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
- Enter RX frequency (e.g., 43266250).
- [MENU] [1][3] [MENU] [1][0] [MENU] --> [EXIT] (Enters desired channel 10, RX added)
- Press [V/M] key to return to MR mode.
5.4 Repeaters Programming
These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use them.
- Press [V/M] key to set the radio to VFO mode.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press [MENU] key.
- Enter [1][2] on the numeric keypad for frequency offset.
- Press [MENU] key to select.
- Use the numerical keypad to enter the specified frequency offset (see "12 OFFSET - Frequency shift amount" in Appendix C).
- Press [MENU] key to confirm and save.
- Enter [1][1] on the numeric keypad for offset direction.
- Use the Up/Down keys to select + (positive) or - (negative) offset.
- Press [MENU] key to confirm and save.
- Optional: Save to memory (see Manual Programming) and/or set up CTCSS.
- Press [EXIT] key to exit the menu.
Note: If you have trouble connecting to the repeater, check your settings or contact the radio system administrator. Some Amateur Radio repeaters use a 1750Hz tone burst to open. See "1750Hz Tone-burst" in Appendix C for details.
5.5 VOX (Voice Activated Transmit)
This function enables hands-free conversations. Speak into the microphone to automatically activate communication.
To Enable/Disable VOX:
- In standby mode, press [MENU] + 25. The screen will display "VOX Switch".
- Press [MENU] key.
- Use the Up/Down keys to turn off/on the VOX function.
To Adjust VOX Level:
- In standby mode, press [MENU] + 26. The screen will display "VOX Level".
- Press [MENU] key.
- Use the Up/Down keys to select the VOX level (1-9).
- Press [MENU] key to confirm.
Note: Level 1 is the least sensitive, level 9 is the most sensitive. VOX is not enabled in Scan or FM Radio mode.
5.6 Dual Watch
This feature allows monitoring two channels simultaneously. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or Disabling Dual Watch Mode:
- Press [MENU] key.
- Enter 38 on the numeric keypad for Dual Watch.
- Press [MENU] key to select.
- Use the Up/Down keys to select Double Wait/Signal Wait/OFF.
- Press [MENU] key to confirm.
- Press [EXIT] key to exit.
5.7 Stopwatch Timer
In standby mode, press [MENU] + 57. The screen displays "STOP WATCH".
Using the Stopwatch Timer:
- When ON, press [MENU] to start counting. Press [MENU] again to re-start counting.
- To exit, stop counting first, then press [EXIT].
5.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control, such as activating amateur radio repeaters.
DTMF Frequencies and Corresponding Codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radio has full DTMF implementation, including A, B, C, and D codes. Numerical keys, *, and #z correspond to DTMF codes. A, B, C, and D codes are located in the [MENU], Up/Down, and [EXIT] keys respectively.
To send DTMF codes, press the key(s) while holding down the PTT key. This works even with keypad lock enabled.
5.9 Customization
The radio allows customization of visual and audible features.
5.9.1 Display Backlight (ABR) - Menu 51
In standby mode, press [MENU] + 51. The screen displays "ABR". Press [MENU] to enter, use Up/Down keys to select ON/5sec/10sec/15sec/20sec delay time, then [MENU] to confirm. Press [EXIT] to return to standby.
5.9.2 Beep Prompt (BEEP) - Menu 32
Enables a beep tone every time a key is pressed.
- In standby mode, press [MENU] + 32. The screen displays "BEEP PROMPT".
- Press [MENU] to enter.
- Use the Up/Down keys to turn ON/OFF the beep function.
- Press [MENU] to confirm and exit.
5.9.3 Voice Function (VOICE) - Menu 30
Enables audible voice confirmation of a key press.
- In standby mode, press [MENU] + 30. The screen displays "VOICE".
- Press [MENU] to enter.
- Use the Up/Down keys to select OFF/ON.
- Press [MENU] to confirm. Press [EXIT] to return to standby.
5.9.4 Language of the Menu (LANGUAGE) - Menu 29
This section shows the language of the MENU (English).
- In standby mode press [MENU] + 29. The display will show "LANGUAGE".
5.9.5 Working Mode (MDF-A) - Menu 39
The radio has four working modes: Frequency (FREQ), Channel (CH), Channel Name (NAME).
To Shift Modes:
- In Standby mode, press [MENU] + 39.
- Use the Up/Down keys to select the desired working mode.
- Press [MENU] again to confirm your selection.
5.9.6 Roger Beep, End Transmission Tone (ROGER) - Menu 33
Roger Beep can be enabled/disabled:
- OFF: Roger Beep disabled
- BEEP: Roger Beep tone at the end of transmission
- In standby mode, press [MENU] + 33. The screen displays "ROGER".
- Press [MENU] to enter.
- Use the Up/Down keys to select OFF/ON.
- Press [MENU] to confirm. Press [EXIT] to return to standby.
5.9.7 Power On Message (POWER ON MSG) - Menu 40
Customize the welcome message displayed when the radio is switched on.
Options: VOLTAGE (power voltage), MESSAGE (welcome message), LOGO (custom pictures).
- In Standby mode, press [MENU] + 40. The display will show "POWER ON MSG".
- Press [MENU] to enter.
- Use the Up/Down keys to select the desired option.
- Press [MENU] to confirm. Press [EXIT] to return to standby.
5.9.8 Power On Password (Power On PWD) - Menu 37
Enables a password requirement when the radio is turned on. The default startup password is 000000.
- In standby mode, press [MENU] + 37. The display will show "POWER ON PWD".
- Press [MENU] to enter.
- Use the Up/Down keys to enable/disable (ON/OFF) the power on password.
- Press [MENU] to confirm. Press [EXIT] to return to standby.
5.9.9 Reset - Menu 56
This transceiver has two Reset modes: VFO and ALL.
- Reset VFO: All settings except channels return to default.
- Reset ALL: All settings return to default.
To Reset VFO:
- In standby mode, press [MENU] + 56. The screen displays "RESET".
- Press [MENU] to enter.
- Use the Up/Down keys to select VFO.
- Press [MENU] to confirm. The display will show "Sure to reset?".
- Press [MENU] again to confirm. The screen will display "Wait...". The transceiver will turn off and reboot.
To Reset ALL:
- In standby mode, press [MENU] + 56. The screen displays "RESET".
- Press [MENU] to enter.
- Use the Up/Down keys to select ALL.
- Press [MENU] to confirm. The display will show "Sure to reset?".
- Press [MENU] again to confirm. The screen will display "Wait...". The transceiver will turn off and reboot.
6. Troubleshooting Guide
If you encounter issues with your radio, refer to the table below for common problems and solutions. If the problem persists, contact your dealer for technical support.
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | Battery installed improperly. Battery power run out. Poor contact due to dirty/damaged terminals. | Remove and reattach battery. Recharge or replace battery. Clean or replace battery. |
| During receiving, voice is weak or intermittent. | Battery voltage low. Volume level low. Antenna loose or installed incorrectly. Speaker blocked. | Recharge or replace battery. Increase volume. Turn off radio, remove and reattach antenna. Clean speaker surface. |
| Cannot communicate with other group members. | Frequency or signaling type inconsistent. Too far away from other members. | Verify TX/RX frequency and signaling type. Move closer to other members. |
| You hear unknown voices or noise. | Interrupted by radios on same frequency. Radio in analog mode with no signaling. | Change frequency or adjust squelch level. Request dealer to set signaling. |
| Unable to hear anyone due to too much noise/hiss. | Too far away from other members. Unfavorable position (e.g., blocked by buildings). External disturbance (electromagnetic interference). | Move closer to other members. Move to an open and flat area, restart radio. Stay away from interfering equipment. |
| Radio keeps transmitting. | VOX turned on or headset not in place. | Turn off VOX. Check headset. |
7. Technical Specifications
| Parameter | Specification |
|---|---|
| Frequency Band | FM65-108MHz (RX); AM108-136MHz (RX); 350-390MHz (RX); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx) |
| Memory Channels | 999 |
| Power Supply | Li-Ion 7.4V/1400 mAh (BL-K6) |
| Operating Temperature | -10°C to +45°C |
| Working Mode | Monoband/Dualband |
| Modulation | F3E(FM) |
| Max. Frequency Deviation | ≤ ±5KHz |
| Spurious Radiation | < -60dB |
| Frequency Stability | ±2.5 ppm |
| Rx Sensitivity | < 0.2uV |
| Audio Output Power | ≥ 500mW |
| Dimensions | 64x121x35mm (LxAxP) |
| Weight | 240g |
Specifications are subject to change without notice.
WARNING: Direct plug-in AC/DC power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
7.1 Transmitter Specifications
| Parameter | Specification |
|---|---|
| Frequency Range (TX) | 144-148 MHz, 420-450 MHz (America version) 144-148 MHz, 430-450 MHz (Canadian version) 144-146 MHz, 430-440 MHz (EU CE version) |
| RF Output Power | 5 Watts Max |
| Modulation | 16KOF3E/11KOF3E |
| Spurious Emission | -16 dBm <1GHz, -16 dBm >1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
7.2 Receiver Specifications
| Parameter | Specification |
|---|---|
| Frequency Range | 108-136, 136-174, 220-260, 350-390, 400-520 MHz (Scan Receiver) 144-146 MHz, 430-440 MHz (EU CE version) |
| Sensitivity | 12dB SINAD: -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 0.75 Watts@16Ω |
| Rated Audio Distortion | ≤5% |
8. User Tips
No specific user tips were available from the provided reviews or Q&A content.
9. Warranty and Support
We promise to carefully 100% inspect quality, specification and quantity of the items before delivery.
- Warranty: We offer ONE YEAR WARRANTY for the radio body, and THREE MONTHS for the battery, charger, and other accessories.
- Warranty Repair/Exchange/Return: Shipping costs for warranty repair/exchange/return must be paid by the buyer.
- Technical Support: If the troubleshooting steps do not resolve your issues, or for any other queries, please contact your dealer for technical support.

For the complete and most up-to-date user manual, please refer to the official PDF document: User Manual (PDF).