1. Introduction
The Ugreen Lvlian CM559 M.2 NVMe SSD Enclosure is a high-performance external storage solution designed for M.2 NVMe solid-state drives. It provides fast and stable data transmission with a theoretical rate of 10Gbps, utilizing a USB 3.2 Gen2 Type-C interface. Its all-aluminum fin pattern design ensures efficient heat dissipation, protecting your SSD and valuable data. This manual will guide you through the setup, operation, and maintenance of your CM559 enclosure.
2. Product Features
- High-Speed Performance: Supports NVMe protocol with a theoretical data transfer rate of 10Gbps (USB 3.2 Gen2 standard).
- Efficient Heat Dissipation: All-aluminum alloy body with a fin pattern panel and 3mm thickened thermal conductive silicone for superior heat management, reducing operating temperature by approximately 10°C and improving efficiency by 20%.
- Broad Compatibility: Compatible with M-key and B&M-key M.2 NVMe SSDs. Supports up to 4TB hard disk capacity.
- Advanced Chipset: Equipped with the RTL9210B main control chip for stable and fast transmission.
- Data Protection: Features UASP acceleration protocol, TRIM command, and S.M.A.R.T function to improve transmission efficiency, writing speed, and data safety. Includes short circuit and overcurrent protection.
- Durable Design: Protective cover with anti-fall design.
- Connectivity: USB Type-C port for versatile connection.
- Included Accessories: Comes with a 0.25m Type-C data cable.
3. Setup Guide
Follow these steps to install your M.2 NVMe SSD into the Ugreen CM559 enclosure:
- Open the Enclosure: Gently slide open or unclip the enclosure cover to reveal the internal M.2 slot.
- Insert the SSD: Carefully align your M.2 NVMe SSD with the slot inside the enclosure. Insert the SSD at an angle and then push it down until it is flat.
- Secure the SSD: Secure the SSD in place using the provided fastener (usually a screw or a rubber stopper). Ensure it is firmly seated.
- Apply Thermal Pad: If a thermal conductive silicone pad is provided separately, peel off the protective films from both sides and place it onto the SSD chip, ensuring good contact with the enclosure's heat dissipation surface. If it's pre-applied, ensure it's correctly positioned.
- Close the Enclosure: Slide or clip the enclosure cover back into place until it is securely closed.
- Connect to Device: Use the included 0.25m Type-C data cable to connect the enclosure to your computer or other compatible device.
4. Operating Instructions
Once your SSD is installed and the enclosure is connected to your device:
- Device Recognition: Your operating system should automatically detect the Ugreen CM559 enclosure as an external storage device.
- Initialization and Formatting (New SSDs Only): If you are using a brand new SSD, it may need to be initialized and formatted before use.
- Windows: Open Disk Management (Right-click 'This PC' -> 'Manage' -> 'Disk Management'). Locate the new disk, initialize it (GPT recommended for larger drives), and then create and format a new simple volume.
- macOS: Open Disk Utility (Applications -> Utilities -> Disk Utility). Select the new disk, click 'Erase', choose a format (e.g., APFS, Mac OS Extended), and a scheme (GUID Partition Map).
- Data Transfer: You can now drag and drop files to and from the SSD enclosure, or use it with any backup or data management software.
- Optimal Performance: For the best 10Gbps transfer speeds, ensure you connect the enclosure to a USB 3.2 Gen2 (or USB 3.1 Gen2) compatible port on your host device.
5. Maintenance
- Cleaning: Keep the enclosure clean and free from dust. Use a soft, dry cloth for cleaning. Avoid liquid cleaners.
- Physical Protection: While the enclosure has a protective cover, avoid dropping it or subjecting it to severe physical shocks to prevent damage to the internal SSD and components.
- Ventilation: Although designed for efficient heat dissipation, ensure the enclosure is not covered or placed in an enclosed space during prolonged heavy use to maintain optimal performance.
- Safe Ejection: Always safely eject the drive from your operating system before disconnecting the cable to prevent data corruption or loss.
6. Troubleshooting
- Q: The drive is not recognized by my computer.
-
- Ensure the USB cable is securely connected to both the enclosure and the computer.
- Try connecting to a different USB port on your computer.
- Test with a different USB cable if available.
- Verify that the M.2 NVMe SSD is correctly seated and secured inside the enclosure.
- For new SSDs, ensure it has been initialized and formatted via Disk Management (Windows) or Disk Utility (macOS).
- Confirm your SSD is an M.2 NVMe (M-key or B&M-key) type, as SATA M.2 SSDs are not compatible with this NVMe-only enclosure.
- Q: Data transfer speeds are slower than expected (10Gbps).
-
- Ensure you are connecting the enclosure to a USB 3.2 Gen2 (or USB 3.1 Gen2) compatible port on your computer. Older USB 2.0 or 3.0 ports will result in lower speeds.
- Check if your computer's USB controller drivers are up to date.
- The actual speed also depends on the performance of your M.2 NVMe SSD and the host device.
- Transferring many small files is generally slower than transferring a single large file.
- Q: The enclosure feels warm during use.
-
- It is normal for the aluminum enclosure to become warm during operation, especially during heavy data transfers, as it is designed to dissipate heat from the SSD.
- Ensure the thermal conductive silicone pad is correctly applied and making good contact with the SSD and the enclosure's heat sink.
- Avoid placing the enclosure in direct sunlight or in poorly ventilated areas during prolonged use.
7. Specifications
| Feature | Specification |
|---|---|
| Product Type | M.2 NVMe SSD Enclosure |
| Model | CM559 |
| Interface | USB 3.2 Gen2 Type-C |
| Theoretical Transfer Rate | 10Gbps |
| Supported SSDs | M.2 NVMe (M-key, B&M-key) |
| Max Capacity | 4TB |
| Chipset | RTL9210B |
| Material | All-aluminum alloy |
| Heat Dissipation | Fin pattern design, 3mm thermal conductive silicone (2w/mk) |
| Features | UASP, TRIM, S.M.A.R.T, Short circuit protection, Overcurrent protection |
| Certification | CE, FCC |
| Origin | Mainland China |
| Package Dimensions (L x W x H) | 15cm x 10cm x 8cm |
| Package Weight | 0.15 kg |
8. User Tips
- Always ensure your M.2 NVMe SSD is securely fastened within the enclosure to prevent disconnections or damage during use.
- For optimal performance, use the shortest possible high-quality USB-C to USB-C cable and connect to a USB 3.2 Gen2 port on your computer.
- Regularly back up important data stored on the SSD, as with any storage device.
9. Warranty and Support
For warranty information and customer support, please refer to the seller's specific policies or contact the 'SUPER ELECTRONICS Store' directly. Keep your purchase receipt for any warranty claims.