1. Introduction
The PowMr 48V 10KW Hybrid Solar Inverter is a versatile power solution designed for both grid-tie and off-grid applications. It features dual MPPT (Maximum Power Point Tracking) for efficient solar energy harvesting, a high maximum AC charging current of 160A, and dual AC outputs for main and second loads. This inverter provides a pure sine wave output, ensuring compatibility with a wide range of household and office appliances. It is compatible with multiple battery types and can operate without a battery.
This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your PowMr Hybrid Solar Inverter.
2. Safety Instructions
- Read all instructions and cautionary markings on the unit and in this manual before installation.
- Do not attempt to disassemble, repair, or modify the unit. Refer servicing to qualified personnel.
- Ensure all wiring is performed by a qualified electrician and complies with local electrical codes.
- Always disconnect all power sources (PV, battery, and AC utility) before performing any maintenance or wiring.
- Wear appropriate personal protective equipment (PPE), including insulated gloves and eye protection, when working with electrical systems.
- Ensure proper ventilation around the inverter to prevent overheating.
- Keep children away from the inverter and its connections.
- Do not install the inverter in areas with flammable materials, excessive dust, or corrosive gases.
3. Package Contents
Upon unpacking, please verify that all items listed below are included and undamaged:
- PowMr 10.2KW Hybrid Solar Inverter
- User Manual
- MC4 Terminal Head (x2)

4. Setup & Installation
Follow these steps for proper installation and initial setup of your inverter:
- Disassemble the Cover: Carefully remove the bottom cover of the inverter to access the wiring terminals.
- Connect the Batteries: Unscrew the terminal screws and connect the battery cables to the designated battery terminals (+ and -).
Tip: Connect the battery first to enable the inverter to accurately identify the battery system voltage.
- Connect AC Input and AC Output: Connect the AC input (utility grid) and AC output (loads) cables to their respective terminals. Ensure correct polarity and secure connections.
- Connect the PV Panels: Connect the solar PV panel cables to the PV input terminals. Ensure the PV input voltage is within the specified range (90-500Vdc).
- Install the Cover Back: Once all connections are secure, reattach the bottom cover of the inverter.
- Check Wiring: Before powering on, double-check all wiring connections to ensure they are correct and secure.
- Turn on the Inverter: Power on the inverter. The LCD display will activate, showing the operation interface.






5. Wiring Diagram
Below are diagrams illustrating the connection of PV panels, batteries, and loads to the inverter, as well as the internal components.


6. Operating Modes
The inverter supports multiple charging and output modes to optimize energy usage based on your preferences and available power sources.
6.1. Battery Charging Modes
- C50 Solar First: Solar energy will charge the battery as the primary priority. Utility power will charge the battery only when solar energy is not available.
- SNU Solar and Utility (Default): Solar energy and utility power will charge the battery at the same time.
- O50 Only Solar: Solar energy will be the only charger source, regardless of utility availability.
6.2. Load Output Modes
- USB Utility First: Utility power will provide power to the loads as the primary priority. Solar and battery energy will provide power to the loads only when utility power is not available.
- SUB Solar First (Default): Solar energy provides power to the loads as the primary priority. If solar energy is not sufficient to power all connected loads, utility will supply power to the loads at the same time.
- SBU Priority: Solar energy provides power to the loads as the primary priority. If solar energy is not sufficient, battery energy will supply power. Utility power is used only when battery voltage drops to a low warning voltage or a specific setting point.

6.3. RGB Working Mode Indicators
The inverter features an RGB indicator that automatically switches colors based on its working mode:
- White Light: Stationary Mode
- Blue Light: Utility Mode
- Purple Light: PV Mode
- Red Light: Battery Mode

7. Monitoring via App
The inverter supports remote monitoring and control through the "SMARTESS" application. A WiFi module and GPRS data may need to be purchased separately for this functionality.

8. Maintenance
Regular maintenance ensures the longevity and optimal performance of your inverter.
- Dust-Proof Screen: The inverter is equipped with a detachable dust-proof screen. Regularly clean this screen to prevent dust accumulation, which can cause short circuits and reduce efficiency.
- Cooling Fans: The inverter features three intelligent cooling fans. Ensure they are free from obstructions and operating correctly to dissipate heat and prevent overheating.
- General Cleaning: Keep the inverter's exterior clean and free from dust and debris. Use a dry, soft cloth for cleaning.
- Connection Checks: Periodically inspect all electrical connections for tightness and signs of corrosion.

9. Troubleshooting
This section addresses common issues you might encounter with your inverter.
- PV Function Not Activated (0W Display): If the LCD displays 0W for PV input power, it indicates that the PV function is not activated. This typically occurs because the input voltage from the PV panels is lower than 150Vdc.
- Solution: Add more PV panels to increase the input voltage of the PV array, ensuring it is not less than 150Vdc.
- Solar Charging Inactive: If solar charging is not activating, ensure the PV input voltage meets the minimum requirement (150Vdc) and that the battery type is correctly set (e.g., LiB for Lithium batteries, which activate after 3 seconds of solar energy presence).
- No Power Output at Night (without battery): This inverter can work without a battery during the day when solar power is available. However, without a backup battery, it will not provide power at night or when the sun is out. For continuous power, a battery bank is required.
10. Specifications
Detailed technical specifications for the PowMr 10.2KW Hybrid Solar Inverter are provided in the tables below.
| Table 1 Line Mode Specifications | ||
|---|---|---|
| INVERTER MODEL | 10.2KW | |
| Input Voltage Waveform | Pure Sine Wave (Utility or Generator) | |
| Nominal Input Voltage | 230Vac | |
| Max AC Input Voltage | 300Vac | |
| Nominal Input Frequency | 50Hz/60Hz (Auto detection) | |
| Efficiency (Line Mode) | >95% (Rated R load, battery full charged) | |
| Transfer Time | 10ms typical (UPS); 20ms typical (Appliances) | |
| Table 2 Inverter Mode Specifications | ||
|---|---|---|
| INVERTER MODEL | 10.2KW | |
| Rated Output Power | 10.2KW | |
| Output Voltage Waveform | Pure Sine Wave | |
| Output Voltage Regulation | 230Vac±5% | |
| Output Frequency | 50Hz | |
| Peak Efficiency | 0.93 | |
| Overload Protection | 3s@≥150% load; 5s@101%~150% load | |
| Surge Capacity | 2* rated power for 5 seconds | |
| Nominal DC Input Voltage | 48Vdc | |
| Cold Start Voltage | 46.0Vdc | |
| No Load Power Consumption | 75W | |
| Table 3 Charge Mode Specifications | ||
|---|---|---|
| Utility Charging Mode | ||
| INVERTER MODEL | 10.2KW | |
| Charging Algorithm | 3-Step | |
| AC Charging Current (Max) | 140A | |
| MPPT Solar Charging Mode | ||
| INVERTER MODEL | 10.2KW | |
| Max. PV Array Power | 10200W | |
| Nominal PV Voltage | 360Vdc | |
| PV Array MPPT Voltage Range | 90Vdc~450Vdc | |
| Max. PV Array Open Circuit Voltage | 500Vdc | |
| Max Charging Current (AC charger plus solar charger) | 160A | |
| Table 4 Grid-Tie Operation | ||
|---|---|---|
| INVERTER MODEL | 10.2KW | |
| Nominal Output Voltage | 220/230/240VAC | |
| Feed-in Grid Voltage Range | 195-253VAC | |
| Feed-in Grid Frequency Range | 49-51±1Hz/59-61±1Hz | |
| Nominal Output Current | 44.3A | |
| Maximum Conversion Efficiency (DC/AC) | 98% | |
| Table 5 Two Load Output Power | ||
|---|---|---|
| INVERTER MODEL | 10.2KW | |
| Full Load | 10200W | |
| Maximum Main Load | 10200W | |
| Maximum Second Load (battery model) | 3400W | |
| Main Load Cut Off Voltage | 44VDC | |
| Main Load Return Voltage | 54VDC | |
11. User Tips
- Initial Battery Connection: Always connect the battery first during installation. This allows the inverter to accurately detect and configure for your battery system's voltage.
- PV Input Voltage: Ensure your solar panel array provides an input voltage of at least 150Vdc for the PV function to activate and for solar charging to begin. If the PV input power displays 0W, increasing the number of panels to meet this threshold is often the solution.
- Battery Compatibility: The inverter is compatible with multiple battery types (AGM, GEL, FLD, LI, SLD, USER). When using Lithium (LI) batteries, ensure the battery type is correctly set in the inverter's settings; the lithium battery will activate after 3 seconds of solar energy presence.
- Performance: Users have reported that the inverter "works really nice" for home applications, indicating reliable performance when properly installed.
12. Warranty & Support
For warranty information, technical support, or service inquiries, please refer to the official PowMr website or contact your authorized dealer. Keep your purchase receipt and product serial number handy for any claims.