Docreate 756

Contents

Docreate 756 Portable Handheld Spot Welder

User Manual

Model: 756

1. Introduction

The Docreate 756 Portable Handheld Spot Welder is a compact and versatile tool designed for DIY battery assembly, mobile phone repair, and other small-scale welding tasks. It features an integrated design, eliminating the need for an external spot welding pen, making it highly portable and convenient for use at home or on the go. With 11 adjustable power levels and multiple safety protections, this device offers precise and firm welding for various nickel sheet thicknesses.

Docreate 756 Handheld Spot Welder with key features
Docreate 756 Handheld Spot Welder, highlighting strong current and welding capability up to 0.25mm nickel plating.

2. Important Safety Warnings

  • Do not modify, disassemble, or attempt to repair this product yourself.
  • Avoid contact with any liquids. Do not immerse the product in water or use it in rain or wet environments.
  • Recommended ambient operating temperature is between 15°C and 50°C. Using outside this range may affect welding performance and product lifespan.
  • Do not use a charger with specifications exceeding 5V-1A for charging the device.
  • Protect the device from drops or impacts, as this may damage internal components.
  • After use, the welding capillary can be in a high-temperature state. Avoid touching it immediately.
  • Always cover the pen cap tightly after use to prevent the striker from falling off.

3. Package Contents

Please check the box for the following items:

  • Host (Spot Welder Unit) x 1
  • Pen Cover x 1
  • 2m Nickel Roll x 1
  • Frosted Paper x 1
  • Type-C Charging Line x 1
  • Copper Needle x 2
Diagram showing the product list
Visual representation of all items included in the package.

4. Product Features

  • Integrated Design: Combines power supply and welding pen into one unit for enhanced portability.
  • Wide Application: Suitable for 18650/26650/36650 cylindrical batteries, mobile phone batteries, and other electronic devices requiring battery repair.
  • User-Friendly Interface: Simple two-button operation with clear labeling for mode and gear adjustment.
  • 11 Adjustable Power Levels: Allows for precise control over welding strength to match different materials and thicknesses (e.g., 1-3 gear for cell phone batteries, 3-6 gear for 0.1mm nickel plate, 6-11 gear for 0.12-0.15mm nickel plate).
  • Multiple Safety Protections: Includes overcharge protection, temperature protection, short-circuit protection, abnormal battery temperature alarm, and low battery voltage alarm.
  • Detachable Welding Needle: The welding needle can be easily replaced for convenience and quick maintenance.
  • LED Display: Clear and intuitive LED indicators for mode, gear, and power status.
  • Automatic Shut-down: Device automatically powers off after 8 minutes of inactivity to conserve battery.
Image highlighting performance upgrades
Performance upgrades and key features of the spot welder, including 4.2V output and 800A current.
Icons representing multiple safety protections
Visual representation of the eight-fold protection system, including quality battery, impact, voltage stabilizing, short circuit, low/high temperature, overcharge, and overdischarge protection.

5. Specifications

Parameter Value
Product Name Small Hand-held Spot Welder
Product Model Docreate-756
Display Type LED
Shell Material ABS
Product Size (Host + Pen Cover) 196*41*25mm
Product Weight (Host + Pen Cover) About 142.4g
Battery Capacity 3000MAH
Charging Input DC 5V = 1A
Output Voltage 4.2V
Output Current 800A (MAX)
Max. Welding Thickness 0.25mm (Nickel Sheet)
Certification CE
Product parameter table for the Docreate 756 Spot Welder
Detailed product parameters and specifications.

6. Setup

6.1 Initial Charge

Before first use, ensure the spot welder is fully charged using the provided Type-C charging cable and a 5V-1A charger. The power indicator lights will show the charging status.

6.2 Attaching/Replacing Welding Needles

The copper welding needles are detachable and can be replaced. To replace, carefully unscrew the old needles and screw in the new ones. Ensure they are securely fastened.

Image showing the detachable welding needle
Illustration of the detachable welding needle for easy replacement.

7. Operating Instructions

7.1 Panel Introduction

  • Mode Indicator Light: Indicates whether the device is in Manual or Automatic mode.
  • Gear Indicator Light: Displays the current power gear setting (1 to 11).
  • Power Indicator Light: Shows remaining battery power (65-100%, 30-65%, 5-30%, <5%).
Close-up of the Docreate 756 Spot Welder's LED display
LED display showing mode, gear, and power indicators.

7.2 Key Functions

  • On/Off Key:
    • Power On/Off: Press and hold for 2 seconds.
    • System Reset: Press and hold for 10 seconds.
    • Manual Spot Welding Output: In Manual mode, after the welding pens touch the metal, short press this key once to initiate a weld.
  • Gear Shift Key:
    • Shift Gears: Short press to cycle through 11 gears. The indicator light will change accordingly.
    • Switch Mode (Manual/Automatic): Press and hold for more than 2 seconds. In Automatic mode, the device automatically detects contact and outputs a weld. In Manual mode, you must press the On/Off key to weld.
  • Combination Key (On/Off Key + Gear Shift Key):
    • Ultra-Low Power Mode: Press and hold both keys for more than 2 seconds. This mode is exited upon charging or a long press of any key.

7.3 Welding Process

  1. Ensure the welding surface is clean, smooth, and free of corrosion.
  2. Select the appropriate gear based on the material thickness (refer to the table below).
  3. Place the nickel sheet and battery in position.
  4. In Automatic mode, touch both welding pens to the metal simultaneously. The device will automatically weld.
  5. In Manual mode, touch both welding pens to the metal, then short press the On/Off key to initiate a weld.
  6. Apply moderate pressure to the welding pens. Too much or too little pressure can affect weld quality.

7.4 Reference Table for Welding Materials

Welding Material Recommended Gear Range
Cell Phone Batteries 1-3
0.10mm Nickel-plated Tape 3-6
0.12mm Nickel-plated Tape 6-11
0.15mm Nickel-plated Tape 6-11
0.20mm Nickel-plated Tape Higher gears (experiment)
0.25mm Nickel-plated Tape Highest gears (experiment)

Note: This table is for reference only. Actual welding results may vary due to material quality, surface condition, and user technique. Adjust gears as needed.

Docreate 756 Spot Welder in action, welding a battery pack
The spot welder being used to assemble a battery pack.

8. Maintenance

  • Cleaning: Keep the welding pens and contact points clean. Use the provided frosted paper or fine sandpaper to lightly polish the tip of the stylus if it becomes oxidized.
  • Storage: Store the device in a dry environment, away from moisture and extreme temperatures.
  • Charging: Always use a 5V-1A charger to maintain battery health.
  • Pen Cover: Ensure the pen cover is securely placed after use to protect the welding pens.

9. Troubleshooting

Fault Description Possible Reasons Solution
Unable to boot Insufficient power
Battery overdischarge
Battery failure
Connect charger to charge
Contact customer service
Contact customer service
Cannot charge Charger/charging cable damaged
Charging failure
Replace charger/charging cable
Contact customer service
No output, unstable welding, nickel penetration, or poor welding results Power is too low
Improper gear adjustment
Oxidation of stylus tip
Welding material not suitable
Uncontrolled output/power damaged
Charge the equipment
Adjust the gear and try more
Use sandpaper to polish it clean and smooth
Replace welding material
Contact customer service
Visual examples of incorrect welding techniques and conditions
Examples of incorrect welding practices, such as single pen use, pens too close, misplaced battery, material corrosion, material too thick, or incompatible battery.

10. User Tips for Improved Welding Quality

  • Ensure the thickness of the objects to be welded is within the product's specified application range (up to 0.25mm nickel sheet).
  • Always keep the welding surface smooth, clean, and free from any contaminants to ensure good contact.
  • Regularly check and clean the tip of the spot welding pen. If oxidized, lightly polish it with the included frosted paper or fine sandpaper.
  • Apply moderate pressure to the pen tip during welding. Excessive pressure can lead to energy concentration, while insufficient pressure may result in a weak weld.
  • Experiment with different gear settings. If the solder joint appears black, try lowering the gear. If the molten pool is too small, increase the gear setting.
Image detailing welding skills and precautions, including a correct welding demonstration
Visual guide for correct welding demonstration and important precautions.

11. Warranty and Support

For detailed warranty information and customer support, please refer to the official product page or contact the seller directly. A comprehensive user manual in PDF format is also available for download: View User Manual (PDF).

© 2023 Docreate. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.