YIERYI YY-1066L, YY-1088G, YY-1088, YY-1080, SGS07, THE01879

Contents

YIERYI Digital Soil Meter Instruction Manual

Models: YY-1066L, YY-1088G, YY-1088, YY-1080, SGS07, THE01879

1. Introduction

The YIERYI Digital Soil Meter is a versatile tool designed to help you understand and optimize your plant's growing environment. Depending on the model, it can measure various parameters including soil pH, moisture, fertility, light intensity, soil temperature, ambient temperature, air humidity, EC (Electrical Conductivity), and salt levels. This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your soil tester.

2. What's in the Box

The contents of your package may vary slightly depending on the specific model purchased. Please refer to the packing list for your model in the Specifications section.

YY-1066L Multi-Function Soil Tester with pH buffer powders and user manual
Example: YY-1066L Multi-Function Soil Tester package contents, including pH buffer powders and user manual.

3. Specifications

This section details the specifications for various models of the YIERYI Digital Soil Meter.

3.1. YY-1066L Specification

ParameterValue
ModelYY-1066L
Name7-in-1 Soil Tester
LightLOW-, LOW, NOR, HGH, HGH+
Soil moistureDRY-, DRY, NOR, WET, WET+
Soil fertility1-99%
Soil PH3-8.5pH
Soil temperature-10 ~ 60°C; 14 ~ 140°F
Air humidity1 ~ 100%
Ambient temperature-10 ~ 60°C; 14 ~ 140°F
DisplayLCD Large Display
Auto Power Off5 minutes
Battery3 * AAA Battery (Not included)

3.2. YY-1088G/YY1088 Specifications

ParameterRange/Resolution/Accuracy
PH measuring range0.01-14.00pH
PH Resolution0.01pH
PH Accuracy±0.05pH
EC measuring range0.01-10mS/cm
EC Resolution0.01mS/cm
EC Accuracy±2% F.S
TEMP measuring range0.1°C-80.0°C; 32.0°F-176.0°F
TEMP Resolution0.1°C; 0.1°F
TEMP Accuracy±0.5°C
Fertility0~99%
Fertility Resolution0.01mS/cm
Fertility Accuracy±2% F.S
Moisture measuring range0~10 level
Light9 level
Work Environment0.1-80°C(32.0-176°F); RH 100%
LCD DisplayBacklight Display
Battery4*AAA Batteries (Battery Not Included)

3.3. YY-1080 Specification

ParameterRange/Resolution/Accuracy
PH measuring range0.00-14.00pH
PH Resolution0.01pH
PH Accuracy±0.05pH
EC measuring range0.01-120mS/cm
EC Resolution0.01mS/cm
EC Accuracy±2%F.S
Air humidity measuring range0~95%
Air humidity Resolution1%
Air humidity Accuracy±2%F.S
TEMP measuring range0.0°C-80.0°C; 32.0°F-176.0°F
TEMP Resolution0.1°C;0.1°F
TEMP Accuracy±0.5°C
Work Environment0-80°C(32.0-176°F); RH 100%
Display LCDBacklight Display
Auto-shutdown5 minutes
Battery4*AAA Batteries (Battery Not Included)

3.4. SGS07 Specification

ParameterValue
ModelSGS07 3-IN-1 Soil Tester
ApplicableMeasure Soil Moisture, pH, Nutrients
PH Range3.0~9.0 PH
Moisture0%~90%
Temp-10℃-90℃ (14°F-194°F)
Size61.71mm * 252.8mm
Battery Type3x AAA Alkaline Batteries Required (Not Included)

3.5. THE01879 Specification

ParameterRange/Resolution/Accuracy
PH measuring range3.5-9PH
Fertility measuring range0-3000us/cm
Air Humidity measuring range0-99%
Soil Moisture measuring range0-99%
Environmental illumination measuring range0-100000 LUX
°C/°F measuring range-9°C-50.0°C, 16°F-122°F
Product nameMultifunction Soil Meter
MaterialABS+Metal probe
BacklightYes
ScreenLCD display
Battery2* 1.5V AAA battery (No included)
YY-1080 Screen Display and Measurement Range table
Detailed screen display and measurement ranges for the YY-1080 model.
YY-1066L Product Size and Probe Size
YY-1066L Product Size: 260*70*30mm, Probe Size: 165mm, Product Weight: 120g (without box).
SGS07 Product Name, Size, Weight, Power, Measurement Function, Usage Scenario
SGS07 Product Name: Digital Soil Tester, Size: 245*60*27mm, Weight: 88g, Power supply: 3 AAA alkaline batteries, Measurement Function: Soil Moisture, Temperature, PH Value, Usage Scenario: Garden, greenhouse, orchard, indoor planting, etc.
Thicker Electrode and High Capacity Battery for YY-1088G/YY1088
YY-1088G/YY1088 models feature a thicker 13mm electrode and use 4*1.5V (AAA) batteries for durable, long-lasting power.

4. Setup

4.1. Battery Installation

Before first use, install the required AAA batteries (not included) into the device. The number of batteries varies by model (3 or 4 AAA batteries). Ensure correct polarity (+/-) when inserting batteries.

Battery installation for YY-1066L
Step 1: Install 3*AAA batteries into the YY-1066L model.
Battery installation for SGS07
Step 1: Install 3*AAA batteries into the SGS07 model.

5. Calibration

The instrument is factory-calibrated, but recalibration may be necessary for high precision or after prolonged use.

5.1. pH Calibration

For pH calibration, you will need pH buffer powders (7.00, 4.00, 10.01) and 250ml of water per solution.

  1. Pour each pH buffer powder separately into a cup with 250ml of water and stir to dissolve.
  2. Switch on the power of the soil meter.
  3. Place the electrode into the 7.00 calibration solution.
  4. Select PH mode (pH will jump).
  5. Press and hold the CAL key for 5 seconds. The display will show '7.0 jumps' and '7.0 calibration complete'.
  6. Clean the electrode with pure water and dry it.
  7. Place the electrode into the 4.00 calibration solution.
  8. Press and hold the CAL key for 5 seconds. The display will show '7.0 Jump'.
  9. Short press the CAL key, '4.0 jumps'. Press CAL again, '10.0 jumps'. '4.0 calibration complete'.
  10. Clean the electrode with pure water and dry it.
  11. Place the electrode into the 10.01 calibration solution.
  12. Press and hold the CAL key for 5 seconds. The display will show '7.0 Jump'.
  13. Short press the CAL key, '4.0 jumps'. Press CAL again, '10.0 jumps'. '10.0 calibration complete'.
  14. Clean the electrode with pure water and dry it.
Video demonstrating the pH calibration process for the soil meter.

5.2. EC Calibration

For EC calibration, you will need 1413µs/cm (1.413mS/cm) calibration solution.

  1. Press the ON/OFF button to turn on the meter, rinse the probe with pure water and dry it.
  2. Put the probe into 1413µs/cm (1.413mS/cm) calibration solution and shake it gently. Wait until the reading is stable.
  3. Press the "CAL" button twice; "mS" will jump.
  4. Press and hold "CAL" for 5 seconds and then release. "CAL" will flash once on the screen, and then a value will flash.
  5. When the value starts flashing, press the "CAL" button (if the flashing value is higher than 1.41) or the "HOLD/TEMP" button (if the flashing value is lower than 1.41) to adjust the value to 1.41.
  6. After adjusting the display value to 1.41mS, release the button and wait for the reading to stop flashing.
  7. After calibration is completed, rinse the probe with pure water and wipe it clean.

6. Operating Instructions

6.1. General Measurement Procedure

  1. Press the ON/OFF button to turn on the tester.
  2. Rinse the probe with clean water and wipe dry.
  3. Insert the probe of the measuring instrument into the soil or solution (gently shake the measuring instrument when the measurement object is a solution). Ensure the probe is inserted at least 3-5 inches (8-10cm) into the soil.
  4. Wait for a few seconds until the reading is stable.
  5. Read the measured values from the LCD display.
  6. Press the ON/OFF button to turn off the instrument.
  7. Rinse the probe, wipe it clean, and store it.
How to use the soil tester: insert, read, clean
General steps for using the soil tester: insert the probe, wait for stabilization, read the value, and clean after use.

6.2. Light Measurement

For models with a light meter:

  1. Press the ON/OFF button to turn on the device.
  2. Place the soil analyzer vertically at the measuring point.
  3. Align the Light Meter with direct sunlight.
  4. Read the instrument values for light intensity.

Note: When measuring, ensure that your body or plant leaves do not obstruct the light sensor. This instrument is designed for natural sunlight; artificial light sources may not yield accurate readings.

Ambient Light Level measurement guide
Guide to ambient light levels: 3 cells (insufficient), 6 cells (moderate), 9 cells (too much).

6.3. Soil Moisture Measurement

Test the soil for wetness to determine if watering is needed. The display will show moisture levels, often indicated by a scale or descriptive terms.

Soil Moisture measurement guide
Soil Moisture guide: 2-3 drops (Dry), 4-5 drops (Medium), 6-7 drops (Wet), 8-10 drops (Too Wet).

6.4. Soil pH Measurement

Soil pH is crucial for nutrient effectiveness and microbial activity. The meter provides a pH range reading.

Soil pH measurement guide
Soil pH range and reference: 3.5-6.5 (Acidic), 7 (Neutral), 7.5-9 (Alkaline).

6.5. Soil EC Measurement

EC (Electrical Conductivity) indicates the amount of nutrients available in the soil. Different plants have different optimal EC ranges.

Soil EC measurement guide
Soil EC guide: 0.01-10.00mS/cm. Poor EC control leads to poor growth, good EC doubles growth.

6.6. Soil Fertility Measurement

Soil fertility measures the soil's ability to provide nutrients for crop growth.

Soil Fertility measurement guide
Soil Fertility range: 0-99%. Poor fertility control leads to poor growth, good fertility control supports healthy growth.

6.7. Soil Temperature Measurement

Soil temperature determines plant survival and provides a comfortable growing environment.

Soil Temperature measurement guide
Soil Temperature Range: -10°C ~ 90°C (14°F ~ 194°F).

6.8. Bluetooth Wireless Connection (for compatible models)

Some models offer Bluetooth connectivity to view temperature and humidity changes through a mobile app, facilitating healthier plant management.

Bluetooth wireless connection for soil tester
View temperature and humidity changes via a mobile app with Bluetooth-enabled models.

6.9. Data Export (for compatible models)

Some models allow data export to Excel or email for detailed analysis.

Data export to Excel/email view
Example of data export functionality to Excel or email via a mobile application.

7. Maintenance

7.1. Cleaning and Storage

Proper cleaning and storage are essential for the longevity and accuracy of your soil meter.

  1. After each use, rinse the probe with pure water and wipe it clean with a soft cloth to avoid rust and corrosion.
  2. Do not immerse the device completely in water.
  3. Store the device in a dry place.
Soil tester care instructions
Important care instructions: Do not insert the probe into hard soil, do not leave it in soil for a long time, wet the soil before testing, and clean the probe after each use.

7.2. Alcohol Cleaning (if needed)

If the probe requires deeper cleaning:

  1. Soak the probe in alcohol for 10 minutes.
  2. Clean the probe gently with a brush.
  3. Dry with a cloth before storing.
Alcohol cleaning instructions for soil tester probe
Instructions for alcohol cleaning: Soak in alcohol, clean with brush, dry with cloth.

7.3. Battery Replacement

When the low battery indicator flashes on the display, it's time to replace the batteries.

  1. Open the battery protective cover.
  2. Remove the old batteries.
  3. Insert new AAA batteries, paying attention to the positive and negative poles.
  4. Close the battery cover.
Battery replacement instructions for soil tester
Steps for battery replacement: Open cover, remove old batteries, insert new ones with correct polarity, close cover.

8. Troubleshooting

Q: What can I do if the meter can't be calibrated?
A: If you encounter issues with calibration, please contact the manufacturer or seller for support. Ensure you are using fresh calibration solutions and following the steps precisely.
Q: Why does the value jump when the test probe encounters air?
A: When the test probe encounters air, it will generate resistance, and it is normal for the value to jump. Ensure the probe is fully immersed in the soil or solution for stable readings.

9. User Tips

  • Do not immerse the probe in the measured object for a long time, as this can slow down the electrode reaction and affect accuracy.
  • Avoid completely immersing the device in water. Only the probe should be inserted into the soil or solution up to the indicated water level line (e.g., 6cm).
  • Do not use the meter to measure pure water, distilled water, or corrosive liquids, as this can damage the probe or provide inaccurate readings.
  • Always insert the probe into soft soil. Do not force the probe into hard stones or compacted soil, as this will damage the probe.
  • For best results, insert the probe into the soil at least 8cm, preferably 10cm or more, to ensure sufficient contact for accurate readings.
  • When calibrating, gently stir the solution several times to ensure no air bubbles are around the electrode, which can interfere with the reading.
  • For soil measurements, it is recommended to wet the soil with water before testing to ensure better conductivity and more accurate moisture readings.

10. Warranty and Support

We are committed to providing high-quality products and services. In case of non-human damage, we offer a 6-month warranty from the date of purchase. For any questions, issues, or support needs, please feel free to contact us. We aim to respond within 24 hours.

For additional information and detailed documents, you may refer to the official user manual PDF: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.