Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your MAXSUN eSport B650ITX WIFI ICE motherboard. Designed for AMD Ryzen AM5 processors, this Mini-ITX motherboard offers high performance with DDR5 memory support, PCIe 5.0, and integrated Wi-Fi 6 for a powerful and compact computing experience.
Figure 1: MAXSUN eSport B650ITX WIFI ICE Motherboard Overview
Setup Guide
Before beginning installation, ensure your system is powered off and unplugged from the wall outlet. Always handle the motherboard by its edges to avoid static discharge.
1. CPU Installation
- Locate the AM5 socket on the motherboard.
- Open the CPU retention mechanism.
- Carefully align the AMD Ryzen AM5 processor with the socket, ensuring the triangular markers match. Do not force the CPU into the socket.
- Close the retention mechanism to secure the CPU.
- Apply thermal paste to the CPU (if not pre-applied on your cooler).
- Install your CPU cooler according to its manufacturer's instructions.
Figure 2: Motherboard with AM5 CPU Socket
2. Memory (RAM) Installation
- Locate the two DDR5 U-DIMM memory slots.
- Open the clips on both ends of the memory slot.
- Align the notch on the DDR5 memory module with the key in the slot.
- Insert the memory module firmly into the slot until the clips snap into place. Ensure both clips are closed.
- For dual-channel operation, install memory modules in both slots.
Figure 3: DDR5 Memory Slots
3. Storage Device Installation
M.2 SSDs:
- Identify the M.2 slots. This motherboard has two M.2 slots (2242/2280 PCIe 4.0 X4/X2 channel SSDs), one on the front and one on the back of the PCB.
- Remove the M.2 standoff screw.
- Insert the M.2 SSD into the slot at an angle.
- Gently push down the SSD and secure it with the standoff screw.
SATA Drives:
- Connect SATA data cables from your storage devices (HDDs/SSDs) to the two SATA 3.0 interfaces on the motherboard.
- Connect SATA power cables from your power supply to the storage devices.
4. PCIe Expansion Card Installation
- Locate the PCIe 5.0 x16 slot.
- Remove the corresponding expansion slot cover from your PC case.
- Align your graphics card or other PCIe expansion card with the slot and press firmly until it is seated correctly.
- Secure the card with a screw to the PC case.
5. Power Connections
- Connect the 24-pin ATX motherboard power connector from your power supply to the corresponding socket on the motherboard.
- Connect the 8-pin ATX 12V CPU power connector from your power supply to the corresponding socket.
6. Front Panel and Fan Connections
- Connect your chassis front control panel headers (F_PANEL) for power button, reset button, HDD LED, and power LED.
- Connect system fans to the system fan headers and the CPU cooler fan to the CPU fan header.
- For ARGB lighting, connect compatible devices to the two 5V ARGB pins and one 12V NRGB pin.
7. Rear I/O Connections
Connect your peripherals to the rear I/O ports as shown in Figure 4.
Figure 4: Rear I/O Panel
- Display Outputs: 1x HDMI 1.4, 1x DisplayPort (DP)
- USB Ports: 2x USB 3.2 GEN1, 4x USB 2.0
- Network: 1x RJ45 (2.5G LAN), Wi-Fi antenna connectors
- Audio: 1x Line In, 1x Line Out, 1x Mic In
- Other: CLR_CMOS button
Operating Instructions
1. Initial Boot and BIOS/UEFI Setup
- After assembling your system, connect a monitor, keyboard, and mouse.
- Power on your system. Press the designated key (usually DEL or F2) repeatedly during startup to enter the BIOS/UEFI setup utility.
- In the BIOS/UEFI, you can configure various settings including:
- Boot order for your operating system installation.
- Memory frequency (supports 4800/5200/5600(OC)MHz, up to 8000(OC+)MHz).
- CPU settings and fan control.
- Enable/disable integrated peripherals.
2. Operating System Installation
This motherboard supports Windows 10 64-bit, Windows 11 64-bit, and Ubuntu 64-bit. Prepare a bootable USB drive with your preferred operating system and follow the on-screen instructions for installation.
3. MAXSUN Sync Software (ARGB Control)
Utilize the MAXSUN Sync lighting control software to customize the ARGB lighting effects connected to your motherboard's 5V and 12V ARGB pins. This allows for personalized aesthetics for your e-sports setup.
Figure 5: MAXSUN Sync Software Interface
Maintenance
1. ESD Protection
The motherboard features an active protection circuit design to strengthen electrostatic protection capabilities, extending the service life of components. However, always take precautions against electrostatic discharge when handling the motherboard or its components. Use an anti-static wrist strap and work on an anti-static mat.
Figure 6: ESD Protection Components
2. Cleaning
Regularly clean your PC case and motherboard to prevent dust buildup, which can lead to overheating and reduced performance. Use compressed air to remove dust from heatsinks, fans, and other components. Ensure the system is powered off and unplugged before cleaning.
3. Firmware Updates
Periodically check the MAXSUN official website for the latest BIOS/UEFI firmware updates. Updating firmware can improve system stability, compatibility, and performance. Follow the instructions provided with the firmware update carefully.
Troubleshooting
1. System Not Booting
- Check Power Connections: Ensure the 24-pin ATX and 8-pin CPU power connectors are securely seated.
- Reseat Components: Reinstall CPU, RAM, and graphics card to ensure they are properly seated.
- Clear CMOS: If you encounter boot issues after changing BIOS settings, use the rear CLR_CMOS button to reset BIOS settings to default. Ensure the system is powered off before clearing CMOS.
- Minimum Configuration: Try booting with only the CPU, one stick of RAM, and the graphics card (if no integrated graphics) to isolate the issue.
2. Network Connectivity Issues
- Wired Network: Ensure the Ethernet cable is securely connected to the RJ45 port. Check your network drivers. The motherboard features a Realtek 8125 2.5G network card.
- Wireless Network: Ensure Wi-Fi antennas are properly connected. Check Wi-Fi drivers and settings in your operating system. The motherboard supports Wi-Fi 6 and Bluetooth 5.2.
Figure 7: Network Port (RJ45)
3. Fan Issues
- Fan Monitoring: The motherboard supports voltage, temperature, and fan monitoring. Check these values in the BIOS/UEFI or through system monitoring software.
- Intelligent Fan Speed Control: Ensure your fans support intelligent speed control if you wish to utilize this feature.
Specifications
| Feature | Specification |
|---|---|
| Model | MS-eSport B650ITX WIFI ICE |
| Motherboard Size | ITX (170*170mm) |
| CPU Socket | AM5 Socket, Supports AMD Ryzen 7000/8000/9000 Series Processors (TDP: 105-180W) |
| Chipset | AMD B650 |
| Memory Slots | 2x U-DIMM DDR5 |
| Max RAM Capacity | 96GB |
| Memory Type Support | DDR5, Dual Channel, Frequencies: 4800/5200/5600(OC)MHz, up to 8000(OC+)MHz |
| Display Outputs | 1x HDMI 1.4, 1x DisplayPort (DP) |
| PCIe Expansion Slot | 1x PCIe 5.0 x16 slot (Supports AMD/Nvidia/Intel discrete graphics cards) |
| Audio Chip | Integrated REALTEK ALC897 |
| Rear Audio Ports | 1x Line In, 1x Line Out, 1x Mic In (Supports simultaneous output of front and rear channels) |
| Front Audio Headers | 1x F_AUDIO header (for front microphone and front audio output) |
| Network Chip | Integrated REALTEK8125BG/D (10/100/1000/2500Mbit) |
| Onboard LAN | 1x RJ45 port (Supports Wake-on-LAN, PXE network boot, UEFI network boot) |
| Wireless Connectivity | Wi-Fi 6 (AX), Bluetooth 5.2 |
| M.2 Slots | 2x (2242/2280 PCIe 4.0 X4/X2 channel SSDs, one on front, one on back PCB) |
| SATA Ports | 2x SATA 3.0 interfaces |
| Rear USB Ports | 2x USB 3.2 GEN1, 4x USB 2.0 |
| Onboard USB Headers | 1x USB 2.0 (9 pins), 1x USB 3.2 GEN1 (16 pins), 1x USB Type-C 10G |
| Power Connectors | 1x 24-pin ATX, 1x 8-pin ATX 12V |
| Fan Headers | 1x CPU fan header, 1x System fan header |
| Front Panel Headers | 1x Chassis front control panel headers (F_PANEL) |
| Hardware Monitoring | Voltage monitoring, Temperature monitoring, Fan monitoring, Intelligent fan speed control |
| ARGB/NRGB Headers | 2x 5V ARGB, 1x 12V NRGB |
| Other Headers/Buttons | 1x Rear CLR_CMOS button, 1x TPM pins, 1x COM_A pins |
| ESD Protection | Air discharge ±8KV Class C, ±6KV Class B; Contact discharge ±6KV Class C, ±3KV Class B (*Tested under the condition of good grounding for the entire machine*) |
| Supported OS | Windows 10 64bit, Windows 11 64bit, Ubuntu 64bit |
| Net Weight | 0.61kg |
| Gross Weight | 0.85kg |
| Color Box Size | 242*207*57mm |
Figure 8: Motherboard Feature Diagram
Warranty and Support
The MAXSUN eSport B650ITX WIFI ICE motherboard comes with a 3-year limited warranty. For technical support, driver downloads, and further assistance, please visit the official MAXSUN website or contact their customer service.
Figure 9: Warranty Information
User Tips
Based on available information, no specific user tips from reviews or Q&A are provided at this time. Always refer to the latest documentation and community forums for additional user-contributed advice.
