K&F CONCEPT KF-150

Contents

K&F CONCEPT KF-150 I-TTL Macro Ring Light Flash Instruction Manual

Model: KF-150

Introduction

Thank you for purchasing the K&F CONCEPT KF-150 I-TTL Macro Ring Light Flash. This manual provides detailed instructions for the safe and effective use of your speedlite. Please read it carefully before operation to ensure optimal performance and longevity of the product.

The K&F CONCEPT KF-150 is a versatile macro ring light flash designed to provide even and shadow-free illumination for close-up photography. It features E-TTL control, manual and multi-flash modes, a clear LCD display, and high compatibility with various camera lenses through a set of adapter rings.

Safety Instructions

WARNING: Failure to follow these safety instructions may result in injury or damage to the product.

  • Never trigger the speedlite near flammable gas or liquid (e.g., gasoline, solvents) to avoid explosion risks.
  • Do not use the speedlite to flash at drivers of vehicles (cars, buses, trains) or riders of motorcycles/bicycles, as this may cause temporary blindness and lead to traffic accidents.
  • Avoid triggering the speedlite at close range directly into human or animal eyes. This can damage retinas and cause severe visual disturbance, potentially leading to blindness.
  • Only use the battery types specified in this manual.
  • Do not expose batteries to high-temperature environments, such as direct sunlight or fire.
  • Remove drained batteries from the speedlite promptly, as alkaline liquid leakage can damage the unit.
  • Do not attempt to charge dry batteries.
  • Protect the speedlite from extremely hot or damp conditions.
  • Never place the speedlite on the car dashboard or in the glove box. When triggering, ensure no light-proof items are placed before or on the reflection shield, as high energy emitted by the speedlite can burn or damage these items.
  • Avoid touching the speedlite immediately after continuous triggering to prevent burns.
  • Do not attempt to disassemble the speedlite yourself due to the risk of electric shock. Non-professional personnel should not repair internal components.
  • During fast continuous shooting under optical output, pause for 15 minutes after every 10 continuous flashes.
  • If continuously using the speedlite with high-speed recycling and a zoom position less than 36mm, the diffuser may generate significant heat.
  • Rapid temperature changes can cause vapor condensation.
  • Do not use any defective batteries with this speedlite.

Product Overview

The K&F CONCEPT KF-150 Macro Ring Light Flash is designed for professional macro photography, providing even and shadow-free illumination. It features a dual flash tube design, an LCD display for easy control, and a range of adapter rings for broad compatibility.

Key Features:

  • Versatile Lighting Control: Supports E-TTL, Manual, and Multi-flash modes. Features a dual flash tube design with independent brightness control for precise lighting.
  • High Compatibility: Compatible with most Nikon and Canon DSLR models with a standard hot shoe. Includes 6 adapter rings (52mm, 55mm, 58mm, 62mm, 67mm, 77mm) to fit various lenses.
  • Built-in Auxiliary Lights: Two LED adjustment lights/AF auxiliary lights assist in focusing in low-light conditions, ensuring clear and sharp images.
  • Ultra HD LCD Screen: A large, clear LCD display with backlighting shows output power, current mode, and battery level, making settings easy to adjust even at night.
  • Flexible Use: Equipped with a spring cable for convenient attachment to the camera or handheld use. Offers a quick recycle time of 2.9 seconds at full power.
  • Overheat Protection: Integrated system to prevent overheating during continuous use.
  • Power Save Mode: Automatically enters hibernation or shuts down after periods of inactivity to conserve battery life.

Nomenclature: Control Unit

Labeled diagram of the K&F CONCEPT KF-150 control unit showing buttons, LCD, and connection points.
Figure 1: Control Unit Layout. This diagram illustrates the various buttons, the LCD screen, and connection points on the speedlite's control unit.
  • Connection Cables: Connects the control unit to the flash ring.
  • Liquid Display: LCD screen showing settings and status.
  • Rear Curtain/Normal Flash Switch: Button to toggle sync modes.
  • RATIO Setting Button: Adjusts flash ratio between tubes.
  • Increase Trim Key: Increases values or settings.
  • ON/OFF Switch Button/Backlight Switch Increase Button: Powers the unit on/off and controls backlight.
  • Setting Key/Confirmation Key: Confirms selections.
  • Decrease Trim Key: Decreases values or settings.
  • Locking Ring: Secures the control unit to the camera hot shoe.
  • Buzzer Switch: Toggles sound prompts.
  • Focus Light/Modeling Light Button: Activates focus assist or modeling light.
  • MODE Mode Selection Button: Cycles through flash modes (TTL, Manual, Multi).
  • Test Flash Button/Charging Indicator: Triggers a test flash and indicates charging status.
  • Reduce Button: Reduces values or settings.
  • Synchronization Jack: For PC sync cable connection.
  • External Power Jack: For connecting external power sources.

Nomenclature: Flash Unit and Adapter Rings

K&F CONCEPT KF-150 Macro Ring Light Flash with control unit and adapter rings.
Figure 2: Flash Unit and Adapter Rings. The ring light connects to the control unit via a coiled cable and attaches to the lens using one of the provided adapter rings.
  • Flash Tube A & B: The two independent flash tubes within the ring light.
  • Focusing Lamp/Modeling Light: Built-in LED lights for focus assistance and continuous modeling.
  • Release Key: Used to detach the flash unit from the adapter ring.
  • Adapter Rings: A set of 6 rings (52mm, 55mm, 58mm, 62mm, 67mm, 77mm) to mount the flash unit onto various lens diameters.

Setup

1. Installing Batteries

The speedlite requires 4 AA batteries (not included). Ensure both the speedlite and camera are turned off before installing batteries.

  1. Open the Battery Compartment: Slide the battery cover in the direction of the arrow to open it.
  2. Insert Batteries: Insert 4 AA batteries, ensuring correct polarity (+ and - signs) as indicated inside the compartment.
  3. Close the Cover: Slide the battery cover back until it clicks into place.

Applicable Battery Types:

  • 4 (AA) Alkaline Manganese Battery (1.5V): Suitable for medium power demand, not rechargeable.
  • 4 (AA) Nickel-Cadmium Battery (1.2V): Rechargeable, quick recycle time.
  • 4 (AA) Nickel-Metal Hydride Battery (1.2V): Higher power than Ni-Cd, less harmful to environment.
  • 4 (AA) Lithium Battery (1.5V): High capacity, low self-discharge, no maintenance.
  • 4 (AA) Hydrogen Oxygen Cell (1.5V) (OXYRIDE): Approximately 1.5 times the capacity of alkaline batteries, suitable for high power consumption.

If using an external acceleration power box, battery box, or power pack, ensure 4 AA batteries are also in the speedlite to supply CPU. Remove batteries if the speedlite will not be used for a long time.

2. Attaching the Speedlite to the Camera

Ensure both the speedlite and camera are turned off before attachment.

  1. Prepare for Attachment: Rotate the locking plate on the control unit up to its highest point.
  2. Install Control Unit: Slide the mounting support of the control unit into the camera's hot shoe.
  3. Secure Control Unit: Tighten the locking plate to secure the control unit firmly to the hot shoe.
  4. Attach Flash Unit to Lens:
    Six adapter rings (52mm to 77mm) for the K&F CONCEPT KF-150 Macro Ring Light.
    Figure 3: Adapter Rings. Select the appropriate adapter ring for your lens diameter.
    • Select the appropriate adapter ring (52/55/58/62/67/77mm) that matches your lens diameter.
    • Screw the adapter ring onto the front of your camera lens.
    • Align the flash unit with the adapter ring and gently push it into place until it locks.

Note: Vignetting may occur in the margin of photos when using the speedlite with 77mm or larger lenses. Ensure the adapter and lens are installed firmly. Press the release button on the flash unit when rotating it to the proper position.

Operating Instructions

1. Power On/Off

  • Press and hold the ON/OFF button for two seconds to turn the speedlite on or off.
  • Power Save Mode: If the speedlite is inactive for 60 seconds, the CPU enters hibernation. Press any key to wake it up. After 30 minutes of inactivity, the CPU will automatically shut down.
  • Charging Indicator: The Test Flash Button/Charging Indicator will light up when the capacitor is fully charged, indicating the speedlite is ready to fire.

2. Flash Modes

Press the MODE button to cycle through the available flash modes: TTL, Manual, and Multi-flash.

TTL Flash Mode (Through-The-Lens)

In TTL mode, the speedlite automatically adjusts flash output for correct exposure. Set your camera to Program (P) or Auto mode for fully automatic flash photography.

  • Exposure Compensation:
    • Press the Increase Trim Key (PLUS) to increase exposure compensation.
    • Press the Decrease Trim Key (MINUS) to decrease exposure compensation.
    • Adjustment range: -3.0EV to +3.0EV in 0.3EV increments.
  • Flash Ratio (A:B): When both flash tubes are active, you can adjust their relative output to create shadow effects.
    • In setting state, use the Increase Trim Key or Decrease Trim Key to select the flash ratio (e.g., 8:1 to 1:8).
    • Note: At extreme ratios (8:1 or 1:8), only one flash tube will light.

Manual Flash Mode

In Manual mode, you have full control over the flash brightness. You can set the flash output from 1/128 power to 1/1 full power in 1/3EV increments.

  1. Press the MODE button until 'M' is displayed on the LCD.
  2. Adjusting Flash Power:
    • Press the Setting Key until the desired flash tube's power value flickers.
    • Use the Increase Trim Key or Decrease Trim Key to adjust the power (e.g., 1/128, 1/64, ..., 1/1).
    • Use the Increase Trim Key or Decrease Trim Key to fine-tune the flash power in 0.3EV increments.

Multi-flash Mode (Stroboscopic Flash)

Multi-flash mode allows for a series of rapid flashes within a single exposure, useful for freezing motion sequences. Set your camera to Manual (M) mode.

  • Press the MODE button until 'Multi' is displayed on the LCD.
  • Set Output Power, Flash Times, and Flash Rate (Hz):
    • Use the Setting Key to select the parameter you wish to adjust (output power, flash times, or Hz).
    • Use the Increase Trim Key or Decrease Trim Key to set the desired values.
    • Flash Times: 1-40 flashes.
    • Flash Rate: 1-100 Hz.
  • Overheating Protection: To prevent overheating, avoid continuous shooting for more than 10 times. Allow at least 15 minutes for cooling after 10 continuous flashes.

3. Advanced Functions

  • FEB (Flash Exposure Bracketing): Allows for automatic bracketing of flash exposure.
    • Press the Increase Trim Key or Decrease Trim Key to set the FEB value (0 to 3.0).
    • For Canon cameras, FEB will activate automatically. For Nikon, confirm camera support and set via camera menu.
  • FV Lock (Flash Value Lock): Locks the correct flash exposure value.
    • For Canon, press the FEL button (or '*' button if FEL is unavailable). For Nikon, press the FV button.
    • The speedlite will pre-flash, and the camera will calculate the suitable output data.
  • Focus Assist / Modeling Lights: Built-in LED lights aid focusing in low light.
    • Press the LAMP button to cycle through off, focus assist, and modeling light modes.
    • The modeling light provides continuous brightness for subject illumination.
  • Rear-curtain Sync: Creates a light trail behind the subject.
    • For Canon, press the Rear Curtain/Normal Flash Switch button in TTL or M mode to toggle.
    • For Nikon, set via the camera menu (no display on flash unit).
  • Sound Prompt: Provides audible feedback for various states.
    • Toggle the buzzer switch to turn sound prompts on or off.
    • Different beeps indicate recycling complete, auto-off, or overheating.
  • Backlight: The LCD screen backlight.
    • Press the Backlight Switch key to turn the backlight on or off.
    • The backlight automatically turns off after 15 seconds of inactivity to save power.

4. Flash Sync Speeds and Apertures

The following table outlines recommended camera settings for various modes when using the speedlite.

Camera ModeShutter Speed SettingAperture Setting
P (Program AE)Automatically (1/60 sec. - 1/X sec.)Automatic
TV/S (Shutter-priority AE)Manually (30 sec. - 1/X sec.)Automatic
AV/A (Aperture-priority AE)Automatically (30 sec. - 1/X sec.)Manual
M (Manual)Manually (Bulb, 30 sec. - 1/X sec.)Manual

Note: 1/X sec. refers to the camera's maximum flash sync speed.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the speedlite. Do not use solvents or abrasive cleaners.
  • Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the speedlite in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery Care: Always use fresh, high-quality batteries. Do not mix old and new batteries or different types of batteries.

Troubleshooting

ProblemPossible CauseSolution
Speedlite does not power on.Batteries are drained or incorrectly inserted.Replace batteries or check polarity. Ensure ON/OFF button is pressed for 2 seconds.
Flash does not fire.Speedlite not fully charged; camera/speedlite not synchronized; incorrect mode.Wait for charging indicator to light up. Check PC sync connection. Ensure correct flash mode (TTL/M/Multi) is selected.
Flash output is too weak/strong.Incorrect exposure compensation or manual power setting.Adjust exposure compensation in TTL mode or manual power in M mode.
Overheating warning on LCD.Continuous high-power flashes.Stop using the flash and allow it to cool down for at least 15 minutes.
Vignetting in photos.Using large lenses (77mm or above) with the ring light.This is a known limitation; adjust shooting distance or focal length if possible.

If problems persist, please refer to the full PDF user manual or contact customer support.

Specifications

Circuit Design:Insulated Gate Bipolar Transistor (IGBT)
Guide No.:GN14 (ISO100)
Transmission Range:20CM - 5M
Flash Coverage:Approx. 80 degrees (top, bottom, left, right)
Firing Configuration:Two flash tubes (together or singly)
Exposure Control Type:TTL, Manual, Multi-flash
Flash Ratio Control:1:8 - 1:1 or 1:1 - 8:1 in 1/2-stop increments
Color Temperature:5500K
Flash Time:1/200s - 1/20000s
Flash Times (Full Power):100 - 1500 flashes
External Interface:Hot shoe, PC port, external charging port
Flash Ready Indication:Approx. 2.9s
Power Sources:4 pcs AA alkaline batteries or AA Ni-MH batteries
Extra Functions:Power saving, overheat protection
Control Unit Dimensions:143 x 73 x 61 mm
Flash Unit Dimensions:130 x 126 x 28 mm
Weight:Approx. 465g

For a complete list of specifications, please refer to the User Manual (PDF).

User Tips

  • When using the ring light for macro shots, experiment with different flash ratios between the two tubes (A and B) to create subtle shadow variations and add depth to your subject.
  • For very close-up subjects, utilize the built-in LED modeling lights to pre-visualize the lighting and assist with precise focusing, especially in dim environments.
  • If you find the flash recycle time too slow, ensure you are using fresh, high-quality AA batteries, preferably Ni-MH rechargeable ones, as they offer faster recycling compared to alkaline.
  • To avoid accidental changes to your settings, remember that the speedlite has an automatic save function, so your last used settings will be retained upon next power-on.
  • If you experience any issues or want to reset all settings, use the "Restore Factory Settings" function by pressing the buzzer key and rear curtain/normal flash switch key simultaneously.

Warranty and Support

K&F CONCEPT provides a 1-year warranty for this product. For warranty claims or technical support, please contact the K&F CONCEPT customer service or your local distributor.

For further assistance, you may also refer to the comprehensive User Manual (PDF) available for download.

Specifications and design are subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.