1. Product Overview
The TAIDEA TG1031D Electric Knife Sharpener is designed for efficient and precise sharpening of various kitchen knives, including metal and ceramic blades. It features diamond and ceramic grinding wheels for high efficiency and fine sharpening results, along with accurate angle guides to reshape the perfect blade.

Figure 1: TAIDEA Electric Knife Sharpener TG1031D with power adapter.
2. Safety Precautions
- Always ensure the power switch is in the 'OFF' position before plugging in or unplugging the sharpener.
- Keep hands and fingers away from the sharpening slots during operation.
- Do not immerse the sharpener in water or any other liquid.
- Keep out of reach of children.
- Use only with the provided power adapter.
- Do not attempt to sharpen serrated knives or scissors with this device.
3. Setup Instructions
- Place the sharpener on a stable, flat surface.
- Ensure the power switch on the sharpener is in the 'OFF' position.
- Connect the power adapter to the sharpener's input port.
- Plug the power adapter into a suitable electrical outlet (100-240 VAC, 50HZ-60HZ).

Figure 2: Connect the power adapter to the sharpener and then to the power supply.

Figure 3: Example of the EU plug power adapter.
4. Operating Instructions
4.1 Applicable Knives
This sharpener is suitable for various kitchen knives, including:
- Ceramic Knives
- Chinese Knives
- European Knives
- Japanese Knives

Figure 4: Examples of knife types compatible with the sharpener.
4.2 Sharpening Process
- Turn on the power switch of the sharpener.
- Coarse Sharpening (Slot 1 - 18° Grinding Angle):
- Insert the knife into the left coarse sharpening groove (marked '1').
- Sharpen the knife from the heel to the tip in a uniform speed. For metal knives, 4-6 seconds; for ceramic knives, 6-8 seconds.
- Repeat the process in the right coarse sharpening groove.
- This stage is for establishing the initial edge and repairing seriously damaged knives.
- Fine Honing (Slot 2 - 20° Grinding Angle):
- Insert the knife into the left fine honing groove (marked '2').
- Sharpen the knife from the heel to the tip in a uniform speed, applying light pressure.
- Repeat the process in the right fine honing groove.
- This stage refines the blade for a razor-sharp finish.
- To ensure blade consistency, sharpen the knife by alternating between the left and right grooves in each stage. Do not apply excessive force.
- After sharpening, turn off the power switch and carefully remove the knife.

Figure 5: Illustrative diagram of the knife sharpening motion.

Figure 6: The sharpener features a 18° grinding angle for coarse sharpening (Slot 1) and a 20° grinding angle for fine honing (Slot 2).

Figure 7: Proper technique for sharpening a knife.
5. Maintenance
5.1 Cleaning
The stainless steel decoration of the sharpener is designed for easy cleaning. Wipe the exterior with a damp cloth after use. Ensure the device is unplugged before cleaning.
5.2 Replacing Sharpening Head
The sharpening head is replaceable, extending the product's life and promoting environmental protection. To replace the sharpening head:
- Ensure the sharpener is unplugged and turned off.
- Gently twist and pull the existing sharpening head to remove it.
- Align the new sharpening head with the slot and push it in, then twist to secure.

Figure 8: Step-by-step guide for replacing the sharpening head.

Figure 9: The removable sharpening head.
6. Troubleshooting
- Sharpener does not turn on: Ensure the power adapter is securely plugged into both the sharpener and the electrical outlet. Check if the power switch is in the 'ON' position. Verify the outlet is functional.
- Knives are not sharpening effectively: Ensure you are using the correct sharpening technique (uniform speed, appropriate pressure). The sharpening head might be worn and require replacement.
- Unusual noise during operation: Turn off the sharpener immediately and inspect the sharpening slots for any obstructions. If the noise persists, discontinue use and contact customer support.
7. Specifications
| Attribute | Specification |
|---|---|
| Product Name | Electric Knife Sharpener |
| Brand Name | TAIDEA (GRINDER) |
| Model Number | TG1031D |
| Type | Sharpeners |
| Material | Other (Diamond grinding wheel) |
| Grinding Material | Diamond |
| Grinding Method | Pull back |
| Grit | 600 and 1000 |
| Grinding Angle (Coarse) | 18° |
| Grinding Angle (Fine) | 20° |
| Rotating Speed | 2000 RPM |
| Voltage | 100-240 VAC, 50HZ-60HZ |
| Size | 200*78.5*81mm |
| Weight | 714g |
| Features | Eco-Friendly, Stocked |
| Certification | CE / EU, CIQ |
| Packaging | Color box |
8. Warranty and Support
All TAIDEA products are sold directly by TAIDEA. For any product-related issues, please contact the seller or manufacturer's customer support for assistance. Keep your purchase receipt for warranty claims.
9. User Tips
- For best results, always use a uniform speed when pulling the knife through the sharpening grooves.
- Avoid applying excessive downward pressure, as this can damage the blade or the sharpener.
- Regularly clean the sharpener to prevent accumulation of metal or ceramic dust, which can affect performance.
- Replace the sharpening head when you notice a decrease in sharpening effectiveness.
- Always test the sharpness of your knife on a piece of paper or a tomato after sharpening to ensure desired results.