ComWinTop CWT-DCVT

Contents

DC Voltage Transmitter User Manual

Model: CWT-DCVT | Brand: ComWinTop

1. Introduction

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the ComWinTop CWT-DCVT DC Voltage Transmitter. This device is designed to convert DC voltage signals into isolated current or voltage signals (e.g., 4-20mA DC, 0-10V DC) for integration with modular instrumentation, DCS, PLC, and other control systems. It ensures galvanic isolation between input, output, and power supply, enhancing system immunity and reliability in industrial environments. The CWT-DCVT is characterized by its compact size, fast response time, low power consumption, and stable temperature characteristics.

Front view of the ComWinTop CWT-DCVT DC Voltage Transmitter
Figure 1: Front view of the CWT-DCVT DC Voltage Transmitter, showing the model label and general appearance.

2. Specifications

The following table details the technical specifications of the CWT-DCVT DC Voltage Transmitter:

ParameterValue
Product NameDC voltage transmitter
Product ModelCWT-DCVT
Input Range0-1000V
Input Impedance≥300KΩ
Output SignalDC0-5V / DC0-10V / DC4-20mA / RS485
Output Load Resistance (Current Signal)RL≤5000Ω
Output Load Resistance (Voltage Signal)RL≥10KΩ
Class0.1%F.S.
Temperature Drift0.005%F.S./°C (-20°C~+55°C)
Response Time≤10mS (0-90%) (TYP)
Dielectric Strength1500V DC/1min (between input, output, and power)
Insulation Resistance≥100MΩ (between input, output, and power)
Power SupplyDC12V / 24V
Rated Power Consumption≤1W (24V, 20mA output)
Working Temperature-20°C~+55°C
Installation Method35mm standard rail
Detailed specifications table for the DC Voltage Transmitter
Figure 2: Visual representation of the product specifications.

3. Installation

3.1 Mounting

The CWT-DCVT transmitter is designed for 35mm standard DIN rail mounting. Ensure the mounting location provides adequate ventilation for heat dissipation and is within the specified working temperature range (-20°C to +55°C).

Side view of the transmitter showing DIN rail mounting
Figure 3: The transmitter mounted on a 35mm standard DIN rail.

3.2 Dimensions

Refer to the following diagrams for the physical dimensions of the transmitter to ensure proper fit and clearance during installation.

Dimensional drawing of the CWT-DCVT transmitter
Figure 4: Product dimensions for 35mm rail mounting (Length: 108mm, Height: 47mm, Width: 25.4mm).
Detailed product size diagram with measurements
Figure 5: Detailed product size diagram (Length: 104mm, Height: 47mm, Width: 25.4mm, 35mm rail).

3.3 Wiring

The transmitter features Euro terminal blocks for secure connections and three-terminal full isolation. Ensure all connections are made correctly according to the wiring diagrams below. The input, output, and power supply are galvanically isolated.

Top view of the transmitter showing terminals
Figure 6: Top view of the CWT-DCVT, indicating input (3,4), output (5,6), and power (7,8) terminals.

3.3.1 Wiring for 4-20mA Output

Connect the DC voltage input to terminals 3(+) and 4(-). Provide DC 24V power to terminals 7(+) and 8(-). Connect the 4-20mA output to terminals 5(+) and 6(-), typically to a DCS or PLC with a load resistor (RL).

Wiring diagram for 0-10V input to 4-20mA output
Figure 7: Wiring diagram for DC voltage input (e.g., 0-10V) to 4-20mA current output, powered by DC 24V. Input terminals are 3(+) and 4(-), Output terminals are 5(+) and 6(-), Power terminals are 7(+) and 8(-).

3.3.2 Wiring for 0-5V or 0-10V Output

Connect the DC voltage input to terminals 3(+) and 4(-). Provide DC 24V power to terminals 7(+) and 8(-). Connect the 0-5V or 0-10V output to terminals 5(+) and 6(-), typically to a DCS or PLC.

Wiring diagram for 0-10V input to 0-5V output
Figure 8: Wiring diagram for DC voltage input (e.g., 0-10V) to 0-5V voltage output, powered by DC 24V. Input terminals are 3(+) and 4(-), Output terminals are 5(+) and 6(-), Power terminals are 7(+) and 8(-).
Comprehensive product wiring diagram
Figure 9: Comprehensive wiring diagram showing connections for positive and negative voltage inputs to current (4-20mA) and voltage (0-5V) outputs, powered by DC 24V.

4. Operation

The CWT-DCVT transmitter converts a DC voltage input (0-1000V) into a scaled, isolated output signal (DC0-5V, DC0-10V, DC4-20mA, or RS485). Once properly installed and wired, the device operates automatically.

4.1 ZERO and SPAN Adjustment

The transmitter includes ZERO and SPAN adjustment potentiometers for fine-tuning the output signal. These are typically used for calibration to match the specific range requirements of your application.

  • ZERO: Adjusts the offset of the output signal. Use this to set the minimum output value corresponding to the minimum input voltage.
  • SPAN: Adjusts the gain or range of the output signal. Use this to set the maximum output value corresponding to the maximum input voltage.

Refer to Figure 6 for the location of the ZERO and SPAN adjustment points.

Output signal options and product features
Figure 10: Illustration of various output signal options and key product features.

5. Maintenance

The CWT-DCVT DC Voltage Transmitter is designed for reliable, long-term operation with minimal maintenance. Follow these guidelines to ensure optimal performance:

  • Cleaning: Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Environmental Conditions: Ensure the operating environment remains within the specified temperature and humidity ranges. Avoid exposure to corrosive gases or excessive vibration.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion. Loose connections can lead to inaccurate readings or intermittent operation.
  • Calibration: If precise measurements are critical, periodic re-calibration using the ZERO and SPAN adjustments may be necessary. The frequency of calibration depends on the application's requirements and environmental stability.

6. Troubleshooting

If you encounter issues with your CWT-DCVT DC Voltage Transmitter, consider the following common problems and solutions:

  • No Output Signal:
    • Verify that the power supply (DC12V/24V) is correctly connected to terminals 7(+) and 8(-) and is providing the correct voltage.
    • Check the input voltage connections to terminals 3(+) and 4(-). Ensure the input voltage is within the specified range (0-1000V).
    • Confirm that the output wiring to the receiving device (DCS/PLC) is correct and secure.
  • Inaccurate Output:
    • Check the input voltage with a calibrated multimeter to ensure it is accurate.
    • Verify the output signal with a calibrated multimeter or current meter.
    • Adjust the ZERO and SPAN potentiometers for calibration.
    • Ensure the output load resistance meets the specifications (RL≤5000Ω for current output, RL≥10KΩ for voltage output).
  • Intermittent Operation:
    • Check all wiring connections for looseness or corrosion.
    • Ensure the operating temperature is within the specified range (-20°C to +55°C).
    • Check for sources of electromagnetic interference (EMI) near the transmitter.

If the problem persists after performing these checks, contact technical support.

7. User Tips

While no specific user reviews or Q&A were provided, general best practices for industrial transmitters include:

  • Always ensure proper grounding to prevent electrical noise and ensure safety.
  • Use shielded cables for input and output signals, especially in noisy industrial environments, to minimize interference.
  • Before making any adjustments or connections, ensure the power supply to the transmitter is disconnected.
  • Document your ZERO and SPAN calibration settings for future reference or troubleshooting.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your vendor or the manufacturer, ComWinTop. Keep your purchase records handy when contacting support.

The product is designed for durability and reliability, featuring good heat dissipation and three-terminal full isolation to ensure stable performance.

Product features: good heat dissipation, three-terminal full isolation, Euro terminal block
Figure 11: Key features of the CWT-DCVT transmitter, including good heat dissipation, three-terminal full isolation, and Euro terminal blocks.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.