YIHUA 982-V

Contents

YIHUA 982-V Digital Soldering Station User Manual

Model: 982-V | Brand: YIHUA

1. Introduction

The YIHUA 982-V Digital Soldering Station is designed for precision and micro soldering applications. This unit is suitable for de-soldering and soldering operations on various surface-mount components and through-hole components, such as SOP, DIP, and SOIC. It features fast heating, digital temperature control, and a compact design for versatile use.

YIHUA 982-V Soldering Station with various tips, solder wire, and tweezers

Figure 1: YIHUA 982-V Soldering Station and included accessories.

Key features of the YIHUA 982-V: Temperature Range, High Heating Rate, Humanized and Multifunctional, Compact and Exquisite

Figure 2: Overview of key features including temperature range, heating rate, and design.

2. Important Safeguards

Read this instruction manual carefully before using the product. Strictly follow all safety guidelines and precautions.

CAUTION!!! WARNING!!!

  • To provide continued protection against risk of electric shock, connect to properly grounded outlets only.
  • Do not immerse in water.
  • Hot Surface, Avoid Contact.
  • Shock Hazard. To provide continued protection against electric shock, disconnect from the power supply when not in use.
  • The soldering iron must be placed on its stand when not in use.
  • HOUSEHOLD AND INDOOR USE ONLY.
  • To prevent electric shock, unplug before replacing the fuse and other service. Replace only with the same type and rating of fuse.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • The soldering iron is only to be used with the power supply unit provided with the appliance.
  • If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  • Any servicing should be performed by an authorized service representative, and the product has no user serviceable parts.
  • To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Store indoors.
  • A fire may result if the appliance is not used with care. Be careful when using the appliance in places where there are combustible materials; do not apply to the same place for a long time; do not use in presence of an explosive atmosphere; be aware that heat may be conducted to combustible materials that are out of sight; place the appliance on its stand after use and allow it to cool down before storage; do not leave the appliance unattended when it is switched on.
  • Hidden areas such as behind walls, ceilings, floors, soffit boards and other panels may contain flammable materials that could be ignited by the heat gun when working in these locations.
  • WARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint may contain lead, which is poisonous. LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL AND SHOULD NOT BE REMOVED USING A HEAT GUN.
  • To ensure personal safety, please turn off the power switch after work is completed; When not in use for an extended period, please unplug the power cord.
  • Do not install nozzle when the hot air gun is turned on, the heat pipe and the nozzle must be cooling. Then install the other nozzle.
  • The soldering iron should only be used for soldering. Do not hit the soldering iron against the work surface to remove flux residues.
  • Soldering produces fumes, ensure there is adequate ventilation.
  • After use, remember that cooling the unit, the handle should be placed on the handle holder.
  • Longer detachable power-supply cords are available and may be used if care is exercised in their use.
  • A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
  • If the bottom of the brass wool tip cleaner contains solid-state rosin, this product contains rosin (colophony), and the substance may cause an allergic skin reaction. When using the tip cleaner (rosin-inside), DO NOT inhale the fume generated or consume the solid-state rosin, DO NOT allow your skin and eyes to get in direct contact with the rosin.
  • To prevent fire hazard, it is mandatory for the battery used to have functions such as short-circuit protection, overheating protection, low-voltage protection, and over-voltage protection before connecting the battery to the soldering iron. Remove the battery from the soldering iron when not in use.

3. Product Specifications

Attribute Value
Model Number982-V
Brand NameYIHUA
OriginMainland China
Rated Voltage Range110V-240V
Rated Frequency50-60Hz
Rated Power40W (210 Heating Element) / 30W (115 Heating Element) / 60W (245 Heating Element)
Temperature Range90°C~450°C / 194°F~842°F
Operating Ambient Temperature0~40°C / 32°F~104°F
Main Unit DimensionsL160*W79*H80mm ±5mm
DisplayLCD
Tip To Ground Resistance<20hms

Note: When the station is connected with a 210 Heating Element, its rated power is 40W. When connected with a 115 Heating Element, its rated power is 30W. When connected with a 245 Heating Element, its rated power is 60W.

Various power plug types: 220V-EU, 110V-US, 230V-UK, 240V-AU

Figure 3: Available power plug types. Please ensure you select the correct plug for your region.

4. Setup and Installation

4.1. Changing the Heating Element / Soldering Tip

  1. Ensure the soldering station is powered off and unplugged.
  2. Allow the heating element and tip to cool completely before handling.
  3. To remove, gently pull the heating element/tip assembly from the soldering iron handle.
  4. Insert the new heating element/tip assembly into the handle, ensuring it is fully seated.
Diagram showing how to draw out a heating element from the soldering iron holder

Figure 4: Drawing out the heating element.

Diagram showing how to correctly insert a heating element into the soldering iron holder

Figure 5: Correctly inserting the heating element.

WARNING: When replacing the heating element during operation (heated), DO NOT touch the heating element or the groove to avoid potential burn injuries. DO NOT place an operational heating element on the heating element groove for an extended period.

4.2. Initial Use and Tip Preparation

Upon the first use of the soldering iron, set the temperature to 250°C/482°F. When the iron is just hot enough to melt solder, coat the soldering iron tip with a layer of solder (the use of rosin core solder is recommended), then set the temperature to your desired temperature.

Various precision soldering tips including C115, C210, and C245 series, with different tip sizes and shapes

Figure 6: Precision soldering tips. Note: This station is NOT suitable for circuits large in size.

5. Operating Instructions

5.1. Power On/Off

Locate the power switch on the side of the main unit to turn the station on or off.

5.2. Temperature Adjustment

The temperature can be adjusted using the '+' and '-' buttons on the main unit or the short-cut buttons on the soldering iron handle. The LCD display will show the set temperature and actual temperature.

Hand holding soldering iron with remote control buttons for temperature adjustment

Figure 7: Remote control buttons on the handle for temperature adjustment.

5.3. Fast Heating

The C210/C245 rapid heating elements allow the station to reach soldering temperature (e.g., 450°C) from room temperature within 2-4 seconds.

Diagram showing fast heating from 90°C to 450°C in 2 seconds

Figure 8: Fast heating capability of the soldering station.

5.4. Sleep Mode and Stand-by Function

This function extends the lifespan of the heating element, conserves energy, and protects the environment.

  • When the soldering iron is placed back into the holder, the soldering iron will enter sleep mode.
  • If the set temperature is 200°C/392°F or higher, the temperature will cool to 200°C/392°F.
  • If the set temperature is below 200°C/392°F, the temperature will remain unchanged.
  • Pick up the soldering iron to wake the station.
  • When the station enters sleep mode for longer than approximately 5 minutes, the station will automatically enter the stand-by mode. Pick up the soldering iron to restart the soldering station.
Diagram illustrating standby mode (temperature drops to 200°C) and sleep mode (after 5 minutes of inactivity, showing a coffee cup icon)

Figure 9: Standby and Sleep Mode operation.

5.5. Digital Temperature Calibration

Temperature inaccuracy caused by operating room temperature changes and replacing new heating cores can be corrected for more precise welding work.

  1. Press and hold '+' and '-' buttons simultaneously for approximately 2 seconds to enter the temperature calibration interface.
  2. Measure the actual temperature of the tip using a thermometer.
  3. Press '+' or '-' to enter the measured temperature.
  4. Once done setting, press '+' and '-' buttons simultaneously to automatically save the data and exit. Calibration is complete.
Steps for digital temperature calibration, including measuring actual temperature and entering correction mode

Figure 10: Digital Temperature Calibration process.

6. Maintenance

6.1. Tip Cleaning and Tinning

  • If a layer of oxidization forms on the surface of the soldering iron tip, it can appear that the tip cannot heat up properly. In this instance, do not increase the temperature. Instead, use a metal wool ball to remove the oxidization.
  • Set the temperature to 300°C (572°F). Once stable, gently rub the soldering iron tip inside the metal wool ball.
  • When the oxidization is partially removed, continue applying solder onto the tip while rubbing it until the soldering tip is completely coated with solder. If the tip is too severely oxidized, replace it.
  • When the operation is complete, use a damped sponge or metal wool ball to clean the residues off the soldering iron tip. Tin the soldering iron tip with a new layer of solder again, then put the soldering iron back to the holder.

6.2. General Care

  • DO NOT use metal files to remove the oxidization on the soldering iron tip. If the soldering iron tip deforms or rusts, replace the soldering iron tip with a new tip.
  • DO NOT apply excessive forces on the soldering tip when soldering. Doing so will NOT improve heat transfer but damage the soldering iron tip instead.
  • Clean the soldering iron tip after use and tin the tip with a new layer of solder to prevent oxidization.

7. Troubleshooting

"Heating Element Not Detected" Error

If the display shows "Heating Element Not Detected", this indicates that the station's sensor module is faulty. You need to replace the heating element (the heating element and the sensor modules). Alternatively, the soldering iron/heating element may not be properly connected.

8. User Tips

  • This soldering station is highly effective for small components and micro soldering tasks.
  • For intricate precision work, consider using a microscope to enhance visibility and accuracy.
  • It is advisable to have a variety of soldering tips (needles) on hand for different applications.
  • The station offers good power for its compact size, making it suitable for various tasks beyond just micro soldering.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact the manufacturer directly. A PDF user manual with additional guides and documents is available for download: View User Manual (PDF).

Video 1: YIHUA 982-V Digital Soldering Station product demonstration, showcasing features like tip changing, cleaning, rapid heating, and standby mode.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.