Introduction
Congratulations on your purchase of the ARRMA VENDETTA 3S BLX Speed Racer RTR. This high-performance 1/8 scale remote control car is engineered for thrilling high-speed action on various surfaces. Designed with durability and ease of maintenance in mind, the VENDETTA 3S BLX features a robust composite chassis, modular components, and powerful brushless electronics. Please read this manual thoroughly before operating your vehicle to ensure safe and optimal performance.

Safety Precautions
- This product is not suitable for children under 14 years of age. Adult supervision is required for younger users.
- Always operate the vehicle in open areas away from people, pets, and obstacles.
- Never operate the vehicle near water, roads, or power lines.
- Ensure batteries are charged safely and correctly. Do not overcharge or short-circuit batteries.
- Disconnect the battery from the vehicle when not in use and during maintenance.
- Avoid touching moving parts during operation.
- Always turn on the transmitter before the vehicle and turn off the vehicle before the transmitter.
Setup and First Use
Package Contents
Your ARRMA VENDETTA 3S BLX package includes:
- ARRMA VENDETTA 3S BLX Speed Racer RTR Vehicle
- Remote Controller (SPEKTRUM™ SLT3 radio transmitter)
- Operating Instructions
- Charger
- USB Cable
- Original Box
- Batteries (if included in RTR version)

Battery Installation and Charging
- Ensure the vehicle and transmitter are turned off.
- Carefully open the battery compartment on the vehicle.
- Insert the provided Lithium Battery (7.4V) into the battery tray. The battery tray size is approximately 6.49 x 2.01 x 1.89 inches.
- Secure the battery and close the compartment.
- Charge the battery using the provided charger and USB cable. Follow the charger's instructions for safe charging. Do not leave charging batteries unattended.
- Install 4 AA batteries (not included) into the remote controller, observing correct polarity.
Transmitter and Receiver Binding
Your VENDETTA 3S BLX comes Ready-to-Go (RTR), meaning the transmitter and receiver are typically pre-bound from the factory. If re-binding is necessary, refer to the SPEKTRUM™ SLT3 manual for detailed instructions. Generally, this involves:
- Powering on the receiver with the bind plug inserted.
- Powering on the transmitter while holding the bind button.
- Waiting for the indicator lights to confirm binding.
- Removing the bind plug and restarting both devices.
Operating Your VENDETTA 3S BLX
Pre-Run Checklist
- Ensure all batteries (vehicle and transmitter) are fully charged.
- Check all screws and fasteners for tightness.
- Inspect tires for damage and ensure they are securely mounted.
- Verify steering and throttle response before driving.
- Ensure the driving area is clear of obstacles and safe for operation.

Driving Controls
- Throttle Trigger: Pull to accelerate forward, push to brake/reverse.
- Steering Wheel: Turn left or right to steer the vehicle.
- Trim Dials: Adjust steering and throttle trim to ensure the vehicle drives straight and stops neutrally when controls are released.
Driving Tips
- Start with gentle throttle inputs to get a feel for the vehicle's power.
- Practice steering in open areas to develop control.
- Avoid prolonged full-throttle operation, especially on rough surfaces, to prevent overheating.
- Be mindful of battery life; stop driving when performance noticeably drops to avoid over-discharging.
Maintenance
Regular maintenance will extend the life and performance of your VENDETTA 3S BLX.
After Each Run
- Clean the vehicle: Remove dirt, dust, and debris from the chassis, suspension, and drivetrain. A soft brush or compressed air is recommended.
- Inspect for damage: Check for bent parts, loose screws, or damaged components.
- Check wheels and tires: Ensure tires are securely glued to the rims and inspect for wear or punctures.
- Disconnect and store batteries: Always disconnect the battery from the vehicle and store it in a safe, cool place.

Periodic Maintenance
- Drivetrain: Inspect gears for wear. Clean and re-grease as needed.
- Suspension: Check shock absorbers for leaks and smooth operation. The oil-filled shocks can be refilled or tuned.
- Bearings: Inspect bearings for smooth rotation. Replace any rough or seized bearings.
- Electronics: Keep the motor, ESC (Electronic Speed Controller), and receiver clean and free of debris. Ensure all connections are secure.

Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Vehicle does not respond | Low battery (vehicle/transmitter), loose connection, binding issue | Charge batteries, check all connections, re-bind transmitter/receiver |
| Loss of range/intermittent control | Weak transmitter batteries, interference, damaged antenna | Replace transmitter batteries, move to a different location, inspect antenna |
| Motor runs but wheels don't turn | Stripped gears, loose driveshaft, broken axle | Inspect drivetrain components, replace damaged parts |
| Vehicle pulls to one side | Steering trim incorrect, bent suspension component | Adjust steering trim on transmitter, inspect suspension for damage |
| Overheating (motor/ESC) | Aggressive driving, incorrect gearing, poor ventilation | Allow components to cool, check gearing, ensure proper airflow, reduce run time |
Specifications
| Feature | Detail |
|---|---|
| Model Number | VENDETTA |
| Scale | 1:8 |
| Type | Car (Flat Sports Car) |
| State of Assembly | Ready-to-Go (RTR) |
| Material | Metal, Plastic |
| Remote Control | Yes |
| Remote Distance | 150m |
| Control Channels | 6 channels |
| Controller Mode | MODE2 |
| Charging Voltage | 7.4V (Lithium Battery) |
| Recommend Age | 14+y |
| Certification | CE |
| Product Length | 23.43 inches (595mm) |
| Product Height | 6.22 inches (158mm) |
| Product Weight | 6.38 lbs (2.9kg) |
| Product Width | 10.43 inches (265mm) |
| Front Track | 10.31 inches (262mm) |
| Rear Track | 10.55 inches (268mm) |
| Wheelbase | 13.11 inches (333mm) |
| Wheel Hexagon Size | 14mm |
| Wheel Width | 1.38 inches (35mm) |
| Final Drive Ratio | 7.125 |
| Battery Tray Size | 6.49 x 2.01 x 1.89 inches |

User Tips
- Battery Care: Always balance charge your LiPo batteries and store them at a storage voltage when not in use for extended periods. This prolongs battery life.
- Gear Mesh: Periodically check your motor's pinion gear and the vehicle's spur gear for proper mesh. Incorrect mesh can lead to stripped gears and reduced performance.
- Suspension Tuning: Experiment with different shock oil weights and spring rates to fine-tune the suspension for various driving surfaces and conditions.
- Tire Maintenance: Keep your HOONS DBOOTS tires clean. For optimal grip, consider tire warmers or light scuffing before high-speed runs.
- Cleanliness: After driving, especially in dusty or dirty conditions, use compressed air to blow out debris from the chassis, motor, and electronics to prevent wear and overheating.
Warranty and Support
For specific warranty information, please refer to the documentation provided with your purchase or contact the retailer. Keep your proof of purchase for any warranty claims.
For technical support, troubleshooting beyond this manual, or spare parts inquiries, please contact the official ARRMA support channels or your authorized dealer. Always use genuine ARRMA replacement parts to ensure compatibility and maintain performance.