feyree Type2 EV Charger EVSE Wallbox

Contents

Feyree Type2 EV Charger EVSE Wallbox User Manual

Model: Type2 EV Charger EVSE Wallbox

Brand: Feyree

1. Introduction

This manual provides essential information for the safe and efficient operation of your Feyree Type2 EV Charger EVSE Wallbox. Please read this manual thoroughly before installation and use, and keep it for future reference.

Feyree Type2 EV Charger EVSE Wallbox with power options and features

Figure 1: Feyree Type2 EV Charger EVSE Wallbox overview.

2. Safety Information

Your Feyree EV charger is designed with multiple safety features. Always adhere to local electrical codes and safety regulations during installation and operation.

2.1. General Safety Precautions

  • Ensure the charger is installed by a qualified electrician if hardwiring is required.
  • Do not use the charger if the cable or connector is damaged.
  • Keep children and pets away from the charging area.
  • Do not immerse the charger in water or expose it to extreme conditions beyond its IP66 rating.

2.2. Built-in Protection Features

Diagram showing RCD Type B leakage protection and other safety features

Figure 2: Comprehensive safety protections.

The charger includes:

  • RCD Type B leakage protection (AC30mA + DC6mA)
  • Over-voltage and Under-voltage protection
  • Lightning Protection
  • Over-current Protection
  • Overheat Protection
  • Ground Protection
  • Overload protection
  • Self-stop when full
  • Emergency power outage protection
  • Short Circuit Protection
  • Relay protection

2.3. Temperature Control Protection

Temperature control chip diagram with thresholds

Figure 3: Temperature control thresholds for safe charging.

The integrated temperature control chip prevents excessive temperature during prolonged charging:

  • Above 85°C: Cut off within 0.2 seconds.
  • Between 70°C and 85°C: Automatic current reduction.
  • Below 65°C: Automatic start charging.

3. Setup and Installation

3.1. Unboxing and Components

Upon opening the package, verify all components are present:

Video 1: Unboxing and overview of the Feyree EV Charger components.

The package typically includes the EV charger unit with cable, a wall-mount bracket, screws, and a user manual.

3.2. Wall-Mount Installation

The charger features a 2-in-1 portable and wall-mount design. To install it as a wall-mounted unit:

  1. Select a suitable location near your parking spot, ensuring it's protected from direct impact and within reach of your vehicle's charging port.
  2. Use the provided wall-mount bracket as a template to mark drilling points on the wall.
  3. Drill holes and insert wall anchors if necessary.
  4. Securely attach the wall-mount bracket using the provided screws.
  5. Slide the charger unit onto the bracket until it clicks into place.
  6. Ensure the charging cable is neatly coiled and stored when not in use.
Image showing the 2-in-1 portable and wall-mount design of the EV charger

Figure 4: Charger can be used as portable or wall-mounted.

Image showing the IP66 waterproof charger mounted on a wall in the rain

Figure 5: Wall-mounted charger with IP66 rating.

3.3. Power Connection

Connect the charger's power plug to a compatible electrical outlet. Ensure the outlet matches the charger's voltage and current requirements (e.g., 7KW 1-Phase, 11KW 3-Phase, 22KW 3-Phase). Different CEE plug types are available depending on the model.

Diagram showing two types of CEE plugs (Model A and Model B) for 7KW, 11KW, and 22KW chargers with dimensions

Figure 6: Available CEE plug types and dimensions.

3.4. App Connection (Wi-Fi/Bluetooth)

The charger supports smart control via a mobile application (Tuya Smart APP). For initial setup, connect the charger to your phone via hotspot or Wi-Fi.

  1. Download the Tuya Smart APP from your device's app store.
  2. Ensure your phone's Wi-Fi and Bluetooth are enabled.
  3. Open the app and follow the instructions to add a new device.
  4. The app will discover the "feyree" device. Select it to connect.
  5. Enter your Wi-Fi network name and password when prompted.
  6. Once connected, you can control the charger via the app.

Note: The app can also be used via Bluetooth within 10 meters after the initial Wi-Fi setup, even without an active Wi-Fi connection (requires your SIM card to have a signal for initial setup).

Diagram showing app connection via hotspot or Tuya Smart APP with WiFi

Figure 7: App connection methods.

Video 2: Demonstrating app connection and settings.

4. Operating Instructions

The Feyree EV Charger offers both manual button control and smart app control for flexible charging management.

4.1. Manual Button Functions

The charger features a display screen and four control buttons:

Diagram of charger buttons: A for Adjust Charging Current, D for Set Delay Time, T for Set Charging Time, and a gear icon for settings

Figure 8: Charger button functions.

  • A (Adjust Charging Current): Press to cycle through available current settings (8A, 10A, 13A, 16A, 20A, 25A, 32A).
  • D (Set Delay Time): Press to set a delay before charging starts (1 to 15 hours).
  • T (Set Charging Time): Press to set the duration of the charging session (1 to 15 hours).
  • Gear Icon (Settings): Long press for 5 seconds to enter the setting interface.
  • Emergency Stop Button: Located at the bottom center, press to immediately stop charging.
Smart Charger features: Adjustable Current, Delay charging, Set charging time

Figure 9: Smart charger features and adjustable settings.

4.2. Smart APP Control

The Tuya Smart APP provides advanced control and monitoring features:

  • Real-time Monitoring: View current, voltage, temperature, power, and charging status.
  • Current Adjustment: Easily adjust the charging current (8A-32A) from your phone.
  • Scheduled Charging: Set specific charging times to take advantage of off-peak electricity rates.
  • Delay Charging: Program a delay before charging begins.
  • Charging Records: Access a log of total charging power, frequency, and duration.
  • Notifications: Receive alerts for fully charged status or potential errors.
Image illustrating scheduled charging to save money during off-peak hours

Figure 10: Schedule charging to optimize electricity costs.

Screenshots of the Tuya Smart APP interface for setting weekly charging plans

Figure 11: Setting weekly charging plans via the Tuya Smart APP.

5. Maintenance

To ensure the longevity and optimal performance of your Feyree EV Charger, follow these maintenance guidelines:

  • Regular Cleaning: Wipe the charger unit and cable with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Inspect Cable and Connector: Periodically check the charging cable and connector for any signs of wear, damage, or corrosion. If any damage is found, discontinue use immediately and contact support.
  • Environmental Protection: The charger has an IP66 rating, making it resistant to dust and powerful water jets. However, avoid prolonged exposure to extreme weather conditions when possible.
  • Storage: When not in use, ensure the charging cable is neatly coiled and the connector is stored in its holder to prevent damage.

6. Troubleshooting

If you encounter issues with your Feyree EV Charger, refer to the following common problems and solutions:

6.1. "err:reset" Message on Screen

If an "err:reset" message appears on the screen after installation or during operation:

  • Press the Emergency Stop Button (located at the bottom center of the control box) to restart the wallbox. This should resolve the issue.
Warm tips for button functions, including how to handle 'err:reset' message

Figure 12: Troubleshooting "err:reset" message.

6.2. Charging Not Starting or Interrupted

  • Check Power Connection: Ensure the charger is securely plugged into the power outlet and the outlet is live.
  • Check Vehicle Connection: Ensure the Type 2 connector is fully inserted into your EV's charging port.
  • Review Display Screen: Check the LCD screen for any error codes or messages.
  • App Settings: Verify that no delay or scheduled charging times are active in the mobile app that might prevent immediate charging.
  • Temperature Protection: If the ambient temperature is very high, the charger might reduce current or stop charging to prevent overheating (refer to Section 2.3).
  • Emergency Stop: Ensure the emergency stop button is not engaged.

6.3. App Connectivity Issues

  • Wi-Fi/Bluetooth: Ensure your phone's Wi-Fi and Bluetooth are enabled.
  • Network Credentials: Double-check that the correct Wi-Fi network name and password were entered during setup.
  • Range: For Bluetooth control, ensure your phone is within 10 meters of the charger.
  • Reset Wi-Fi: If issues persist, long-press the gear icon button for 5 seconds to enter the settings menu, then navigate to "Reset Wifi" and follow the on-screen instructions or app prompts to re-establish the connection.
Image showing the charger's menu for settings, including Reset Wifi and Ground Check

Figure 13: Accessing settings menu for Wi-Fi reset.

7. Specifications

The Feyree Type2 EV Charger EVSE Wallbox is available in various configurations. Key specifications are detailed below:

FeatureSpecification
Brand Namefeyree
Charger TypePortable & Wallmounted EV charger
Power Options7KW / 11KW / 22KW
Number of Phases1 Phase (for 7KW) / 3 Phase (for 11KW, 22KW)
Current (Adjustable)8A-10A-13A-16A-20A-25A-32A
Voltage85V-264V-380V (depending on model/phase)
Input Frequency50Hz-60Hz
RCD ProtectionTypeB AC30mA+ DC6mA
IP RatingIP66
Operating Temperature-30°C ~ +55°C
Cable Length5m
MaterialCopper Alloy, Silver Plating (for pins)
Weight3.8KG
Dimensions (L x W x H)38cm x 38cm x 11cm (Control Box: 355mm x 152mm x 85mm)
Specifications for 7.6KW 1P 32A model

Figure 14: 7.6KW 1-Phase Model Specifications.

Specifications for 11KW 3P 16A model

Figure 15: 11KW 3-Phase Model Specifications.

Specifications for 22KW 3P 32A model

Figure 16: 22KW 3-Phase Model Specifications.

Image detailing high-quality materials used in the charger, including copper cable and silver-plated pins

Figure 17: High-quality materials and plug types.

Image showing compatibility with various EV brands

Figure 18: Compatible with all major EV brands.

8. Warranty and Support

Your Feyree EV Charger comes with a 2-Year Warranty, ensuring peace of mind regarding product quality and performance.

Image highlighting 2-Year Warranty and 24-Hour Customer Service

Figure 19: Warranty and support information.

For any technical assistance, product inquiries, or warranty claims, please contact Feyree customer service. 24-Hour Customer Service is available to assist you.

9. User Tips

  • Phase Selection: Be aware that the charger models are designed for either single-phase (7KW) or three-phase (11KW/22KW) charging. Ensure you have selected the correct model compatible with your electrical supply and vehicle.
  • Wall Mount Durability: While the charger is designed for both portable and wall-mounted use, the wall holder is a separate component. Handle with care during installation and removal to prevent damage.
  • App Connectivity: For optimal app performance, ensure a stable Wi-Fi connection during initial setup. Bluetooth control offers convenience for local adjustments once paired.
  • Off-Peak Charging: Utilize the smart app's scheduling feature to charge your EV during off-peak electricity hours to save on energy costs. Local electricity policies may vary.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.