1. Introduction
The Seauto Seal SE is an advanced wireless automatic pool cleaner designed to efficiently maintain the cleanliness of both in-ground and above-ground pools. Featuring intelligent route planning, powerful suction, and dual-brush scrubbing, it provides comprehensive cleaning for your pool's floor, walls, and waterline. This manual provides essential information for the proper setup, operation, and maintenance of your Seauto Seal SE pool cleaner.

Figure 1: Seauto Seal SE Wireless Automatic Pool Cleaner
2. What's in the Box
Upon unboxing, please ensure all the following components are present:
- Seauto Seal SE Robotic Pool Cleaner Unit
- Power Adapter/Charger
- Filter Basket
- User Manual (this document)
- Retrieval Hook

Figure 2: Included components with the Seauto Seal SE
3. Specifications
| Feature | Specification |
|---|---|
| Applicable Pool Shapes | In-ground pools, above-ground pools (on flat ground) |
| Max Pool Size | Up to 2000 sq ft (200 m²) |
| Water Depth Supported | 1.6 - 16.4 ft (0.5 - 5 m) |
| pH Value Supported | 7.0 - 7.8 |
| Filter Density | 250 μm |
| Debris Type | Leaves, algae, stones, pollen, soil, etc. |
| Battery Capacity | 7800mAh |
| Battery Lifespan | 10000+ hours |
| Suction Motor Quantity | 1 |
| Motor Power | 180W |
| Flow Rate | 80 GPM |
| Features | Cordless, Press & Go, Auto-Dock when low battery, Floor Cleaning, Built-in Battery |
4. Setup
4.1 Initial Charging
Before first use, fully charge the Seauto Seal SE. Connect the power adapter to the cleaner and a power outlet. The charging indicator will show the charging status. A full charge takes approximately 2.5 hours.

Figure 3: Rapid charging of the Seauto Seal SE
4.2 Preparing for Deployment
Ensure the filter basket is clean and properly installed before placing the cleaner in the pool. The cleaner is designed for immediate use without complex app connections.
5. Operating Instructions
5.1 Starting the Cleaning Cycle
- Ensure the Seauto Seal SE is fully charged.
- Press the start button on the unit. No app connection or additional settings are required.
- Gently submerge the cleaner into the pool. It will automatically begin its cleaning cycle.
The cleaner utilizes SonarNav Pro Smart Navigation to automatically plan its route, ensuring comprehensive coverage. It will clean walls first, then proceed to the pool bottom.

Figure 4: SonarNav Pro Smart Navigation in action
5.2 Cleaning Modes and Coverage
The Seauto Seal SE offers full cleaning coverage, including:
- Floor Cleaning: Efficiently removes debris from the pool floor.
- Wall Cleaning: Climbs and scrubs pool walls.
- Waterline Scrubbing: Cleans along the pool's waterline.

Figure 5: Visual representation of full cleaning coverage

Figure 6: Waterline scrubbing and wall cleaning capabilities
5.3 Automatic Docking
When the battery is low, the Seauto Seal SE will automatically dock itself, making retrieval easier.
5.4 Product Demonstration Video
Video 1: Seauto Seal SE Robotic Pool Cleaner in action, demonstrating unboxing, features, and in-pool cleaning.
6. Maintenance
6.1 Cleaning the Filter Basket
Regularly clean the filter basket to ensure optimal cleaning performance. The filter basket is designed for easy removal and rinsing.
- Remove the cleaner from the pool.
- Open the cleaner's top cover to access the filter basket.
- Remove the filter basket.
- Rinse the filter basket thoroughly with water to remove all collected debris.
- Reinstall the clean filter basket and close the top cover securely.

Figure 7: Easy to flush filter basket for simple cleaning
6.2 Battery Care
The Seauto Seal SE features a replaceable waterproof battery. For long-term battery health, ensure the unit is fully charged before storage and recharged periodically if stored for extended periods.
7. Troubleshooting & Limitations
7.1 General Limitations
- The cleaner is not designed to clean the water line or climb steps that are too steep.
- It cannot effectively clean trash floating on the pool surface or very large leaves.
- Not suitable for pools with a slope gradient equal to 90 degrees.
- Not recommended for pools larger than 2150 square feet (200 m²).
7.2 Common Issues
- Cleaner not moving or cleaning effectively:
- Check battery level and ensure it's fully charged.
- Clean the filter basket; a clogged filter can reduce suction power.
- Verify that no large debris is obstructing the brushes or wheels.
- Cleaner not covering entire pool area:
- Ensure the pool size is within the recommended specifications (up to 2000 sq ft).
- Confirm pool pH is within 7.0-7.8 for optimal performance.
- Allow the cleaner to complete its full cycle; its intelligent planning covers the area over time.
8. User Tips
- For best results, ensure the pool water is within the recommended pH range (7.0-7.8).
- Always fully charge the cleaner before each use to maximize cleaning time and efficiency.
- Regularly inspect and clean the filter basket after each cleaning cycle, especially if the pool has a lot of debris.
- The "Press & Go" feature means you simply press the start button and submerge the unit; no complicated app setup is needed for basic operation.
- The cleaner's intelligent route planning is designed to cover the entire pool, starting with walls and then the floor, without manual intervention.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact information provided with your purchase documentation or visit the official Seauto website. Keep your proof of purchase for warranty claims.