BAOFENG W31

Contents

Baofeng W31 Mini Walkie Talkie User Manual

Model: W31 Series (BF-W31, BF-WP31, MP31 Pro)

Introduction

This manual provides essential information for the safe and effective use of your Baofeng W31 Mini Walkie Talkie. Please read all instructions carefully before operation to ensure optimal performance and user safety.

For a detailed PDF version of this manual, please refer to the User Manual (PDF).

Safety Information and Intended Use

To prevent bodily injury or property loss, adhere to the following guidelines:

Intended Use

  • The product is designed for reliable wireless communication across various industry sectors.
  • Users must have full knowledge of RF exposure and control their exposure to meet occupational limits.
  • Always follow all security instructions in this document and general safety regulations.
  • Use the product exclusively with frequencies licensed by the respective authority.
  • The product should be configured appropriately by the dealer.
  • Operators should be well-trained and familiar with applicable standards.

RF Radiation Information

This radio complies with RF energy exposure standards and guidelines, including:

  • United States Federal Communications Commission (FCC) regulations (47 CFR § 1.1307, 1.1310 and 2.1093).
  • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005.
  • Canada RSS102 Issue 5 March 2015.

To control exposure and ensure compliance, always adhere to the following procedures:

  • Do not remove the RF Exposure Label.
  • User awareness instructions should accompany the device when transferred.
  • Do not use if operational requirements are not met.

Operating Instructions for RF Exposure Compliance:

  • Transmit no more than 50% of the time (Push-to-Talk (PTT) key pressed). Release PTT to receive.
  • Keep the radio unit at least 2.5 cm (1 inch) away from the face during transmission.
  • When worn on the body, use an approved holder, holster, case, or belt clip.
  • Use only approved antennas, batteries, and accessories to avoid exceeding FCC RF exposure guidelines.
  • Contact your local dealer for optional accessories.

FCC Regulations and Statement

This equipment complies with FCC Rules Part 15 for Class B digital devices. It generates and radiates radio frequency energy. If not installed and used according to instructions, it may cause harmful interference. If interference occurs, try to correct it by reorienting the antenna, increasing separation, or consulting a technician.

Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received.

Note: Unauthorized changes or modifications may void the user's authority to operate the equipment.

IC Statement (Industry Canada)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to not causing interference and accepting any interference received.

EU Regulatory Conformance

The product complies with essential requirements of Directive 2014/53/EU and other applicable EU regulations (2006/66/EC, 2011/65/EU, 2012/19/EU). This information applies to EU countries only.

Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate near fuels, chemicals, explosive atmospheres, or flammable materials.
  • Do not operate near blasting areas.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication is prohibited.

Important Tips:

  • Do not use unauthorized or damaged accessories.
  • Keep the product at least 2.5 cm away from your body during transmission.
  • Avoid prolonged high-volume reception.
  • In vehicles with airbags, do not place the product in the airbag deployment area.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Continuous transmission may cause heat accumulation; allow for cooling.
  • Handle with care.
  • Do not disassemble, modify, or repair without authorization.

Protect Your Hearing:

  • Do not place the radio's speaker directly against your ear when not using a headset.
  • Use the lowest necessary volume.
  • Increase volume only in noisy surroundings.
  • Turn down the volume before adding a headset or earpiece.
  • Limit high-volume headset/earpiece use.
  • Excessive sound pressure from earphones can cause hearing loss.

Setup and Assembly

Package Contents

Verify all items are present upon unboxing. If any item is missing, please contact your dealer.

Package contents for 1PCS Baofeng W31 radio
Figure 1: Package contents for a single unit (Radio, Antenna, Battery, Belt Clip, Strap, Manual)
Package contents for 2PCS Baofeng W31 radios
Figure 2: Package contents for two units (2x Radio, 2x Antenna, 2x Battery, 2x Belt Clip, 2x Strap, 2x Manual)

Standard package includes:

  • 1 or 2 x Radio Unit
  • 1 or 2 x Antenna
  • 1 or 2 x Li-Ion Battery Pack (1500mAh)
  • 1 or 2 x Belt Clip
  • 1 or 2 x Wrist Strap (Sling)
  • 1 or 2 x USB Type-C Charging Cable
  • 1 or 2 x Owner's Manual
  • Optional: Headset, Programming Cable, 48cm antenna (depending on selected variant)

Main Controls and Parts of the Radio

Diagram of Baofeng W31 radio controls and ports
Figure 3: Baofeng W31 Main Controls and Ports
  1. Antenna
  2. PTT (Push-to-Talk) Button: Press to transmit, release to receive.
  3. SK1 (+/Channel UP) Key: Increases channel number.
  4. SK2 (-/Channel Down/Monitor) Key: Decreases channel number, activates Monitor function.
  5. Battery Release Latch
  6. Type-C USB Charging Port
  7. Power Switch/Volume Control Knob: Rotate clockwise to turn on and increase volume, counter-clockwise to decrease volume and turn off.
  8. LED Indicator: Red for transmitting (TX), Green for receiving (RX).
  9. Speaker
  10. Type-C Charging LED
  11. External Speaker/Mic Jack: Allows connection of external devices like headsets or microphones (2-pin Kenwood Port).

LED Status Indications

The top LED will help you to identify the current radio status.

LED IndicationRadio Status
Constant RedTransmitting
Constant GreenReceiving

Battery Recharge

Your Baofeng W31 features convenient Type-C USB charging.

Type-C Fast Charging options for Baofeng W31
Figure 4: Type-C Fast Charging options (Car, PC, Power Bank, USB Socket Plug)
Detail of Type-C charging port on Baofeng W31
Figure 5: Close-up of the Type-C charging port
  1. Ensure your radio is turned OFF before charging.
  2. Connect the Type-C USB cable to the Type-C USB charging port at the bottom of the battery (open the protective cover).
  3. Connect the other end of the USB cable to a power source (e.g., car charger, PC, power bank, or USB socket plug).
  4. A fully depleted battery will typically charge in 2-5 hours. The charging indicator light at the bottom of the battery will be red during charging and turn off when charging is complete.

Important:

  • It is recommended to turn off your radio while charging. If left on, you may not be able to transmit if the battery is completely empty.
  • For optimal battery life, remove the radio from the charger within 6 hours of full charge. Do not store the radio connected to the charger for extended periods.
  • Use only authorized batteries, chargers, and power adapters.

Using a Headset or External Speaker/Microphone

Diagram showing headset connection to Baofeng W31
Figure 6: Connecting a headset to the radio

To use an optional speaker/microphone or headset:

  1. Open the rubber cap covering the external speaker/mic jack on the side of the radio.
  2. Insert the plug(s) of your accessory into the SPK/MIC jacks.
  3. Adjust the earbud and microphone to your desired position.

Important:

  • Your radio is not submersible or waterproof when the headset jack is in use.
  • When removing the headset, ensure the jack cover is fully pressed into place to restore its waterproof capability.

General Radio Operation

Power On/Off and Volume Adjustment

  1. To turn the radio ON, rotate the Power Switch/Volume Control knob clockwise until you hear a "click".
  2. Continue rotating clockwise to increase the volume, or counter-clockwise to decrease it.
  3. To turn the radio OFF, rotate the knob counter-clockwise until you hear a mechanical "click".

Channel Selection

In standby mode, press the Channel Up (+) or Channel Down (-) key to select your desired channel. If the voice prompt function is enabled, the radio will announce the channel number.

Transmission

To communicate with your group, all radios must be set to the same channel.

  1. Briefly press the Channel Down (-) key to activate the Monitor feature (see Monitor section below) to ensure the frequency is not busy.
  2. Press and hold the PTT (Push-to-Talk) key to transmit your message.
  3. Release the PTT key to receive.

Note:

  • Only one user can transmit at a time. Avoid transmitting while receiving.
  • Transmission consumes significant battery power; use sparingly to prolong battery life.
  • If you cannot contact a station you can receive, they might be using CTCSS tones or DCS codes.

Monitor Function

The Monitor feature allows you to listen to weak signals by temporarily opening the Squelch. To activate, press and hold the Channel Down (-) key.

VOX (Voice Operated Exchange) Function

VOX enables hands-free communication without pressing the PTT button. Simply speak towards the microphone, and the radio will automatically transmit.

  • The VOX sensitivity can be adjusted in 5 levels (1-5) using programming software. Level 2 is the default, and 5 has the lowest sensitivity.
  • You can enable/disable VOX and select sensitivity levels via the programming software (CPS programming path: Edit > VOX > VOX Level).
Image illustrating VOX function for hands-free communication
Figure 7: VOX Function for hands-free operation

Scan Function

To use the Scan function, all 16 channels must be programmed.

  • If you turn on the radio on Channel 16, scanning will start automatically.
  • Scanning stops on a busy channel when a signal is detected.
  • If PTT is pressed during a scan, you will transmit on the last busy channel.
  • Channel 16 is the priority channel; if no signal is detected when PTT is pressed, the radio will transmit on Channel 16.
  • To turn the scan function ON or OFF, turn on the radio while pressing and holding the PTT + Channel Down (-) keys on Channel 16. Repeat to toggle.

Squelch

The Squelch function suppresses background noise on free channels and allows reception of weak signals. It has 10 adjustable levels (0-9) via programming software:

  • Level 0: Squelch is off.
  • Levels 1-9: Different levels of noise reduction. Higher levels mean stronger Squelch.
  • Default Squelch level is 4.

Caution:

  • Do not set Squelch too high, as you may miss weaker signals.
  • An excessively low Squelch may activate even when no signals are present.
  • Always adjust Squelch when no signals are present.

CTCSS/DCS Tones (Privacy Codes)

CTCSS (Continuous Tone-Coded Squelch System) and DCS (Digitally Coded Squelch) tones act as "access codes". They allow your radio to communicate only with users on the same channel who have set the same tone/code. This prevents reception of undesired signals from other stations on the same frequency but with different CTCSS/DCS tones.

  • Each channel can be set with up to 50 CTCSS codes and 210 DCS codes.

Quick Operation Radio (Without Programming Software)

You can perform the following quick operations by combining the PTT + Channel Down (-) keys:

  • On Channel 1: Press and hold PTT + Channel Down (-) while turning on the radio to toggle VOX function (VOX ON or VOX OFF voice prompt).
  • On Channel 15: Press and hold PTT + Channel Down (-) while turning on the radio to switch the voice prompt language between Chinese and English.
  • On Channel 16: Press and hold PTT + Channel Down (-) while turning on the radio to toggle the Scan function.

Maintenance

Battery Maintenance Instructions

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth to ensure normal charging.
  • Charge the battery between 5°C and 40°C (41°F and 104°F). Charging outside this range may reduce battery life or cause leakage.
  • If charging a battery attached to the product, turn the product off for a full charge.
  • Do not remove the battery or unplug the power cord during charging to ensure a smooth process.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heat sources for prolonged periods.
  • Do not squeeze, penetrate, or remove the battery housing.

General Care

  • Handle the product with care to avoid damage.
  • Do not disassemble, modify, or repair the product or its accessories without authorization.
  • Clean the radio with a soft, damp cloth. Avoid harsh chemicals or solvents.
  • If the radio is exposed to water (and not waterproof), dry it thoroughly before use or charging.
Image showing Baofeng W31 being used in various environments like construction, warehouse, rescue, and mountaineering
Figure 8: Multi-function radio suitable for various uses
Image showing Baofeng W31 radios with water splash, indicating waterproof feature
Figure 9: Baofeng W31 waterproof feature

Troubleshooting Guide

ProblemSolution
The radio doesn't switch onBattery may be exhausted (recharge). Incorrect installation (reinstall).
Battery recharge doesn't last longBattery pack is old (replace). Battery pack not completely charged (ensure full charge).
Reception LED turns on but no sound heardVolume is too low (increase). CTCSS/DCS codes do not match your group (verify codes).
The keypad doesn't workKeypad lock function may be enabled (disable).
Reception of other group signal while transmittingChange to another CTCSS/DCS for your group.

NOTE: If these solutions do not resolve your issues, please contact your dealer for technical support.

Technical Specifications

General
Frequency Range400-470MHz
Working Temperature-20°C to +55°C (-4°F to +131°F)
Operating VoltageDC 3.7V ±10%
Operation ModeSimplex
Dimensions (without antenna)61 x 32 x 114 mm (2.4 x 1.26 x 4.49 inches)
Weight (Battery pack included)200g (0.44 lbs)
Antenna Impedance50Ω
Battery Capacity1500mAh Li-ion
Battery Life (typical use)Up to 18 hours
Maximum Range3km-5km (Up to 5 km range*, *Range may vary depending on environmental and/or topographical conditions)
Storage Channel16 Channels
Waterproof / Water-ResistantIP55
Connector2-pin Kenwood Port
Charging PortUSB C Charging
MaterialPlastic
DisplayNo
Band TypeSingle Band
CertificationCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee
Transmitter
Output Power0.5W-3W (≤2W/≤0.5W ERP)
Frequency Stability±2.5PPM
Max Frequency Deviation≤2.5KHz
Audio Distortion≤3%
Adjacent Channel Power< 60 dB
Transmission Current≤1000mA
Receiver
RF Sensibility<0.2μV @ 20 dB SINAD
Audio Distortion≤3%
Audio Response300Hz ± 3KHz
Adjacent Channel Selectivity≥55dB@12.5KHz
Inter Modulation and Rejection≥55dB@12.5KHz
Conducted Spurious Emission≤-57dB@12.5KHz
Rated Audio Power Output0.75W @8 ohms
Receive Current≤380mA

NOTE: All specifications are subject to change without prior notice or liability.

User Tips

  • Optimal Range: For best communication range, ensure a clear line of sight. Obstacles like buildings and dense foliage can significantly reduce range.
  • Battery Life: To maximize battery life, use the lowest effective power setting and avoid continuous transmission.
  • Programming: While basic functions are accessible directly, consider using the programming software for advanced customization of channels, VOX levels, and privacy codes.
  • Water Resistance: The radio is IP55 water-resistant, meaning it can withstand splashes and light rain. However, it is not designed for submersion. Always ensure port covers are securely closed.

Support and Contact

For technical support, warranty inquiries, or further assistance, please contact your authorized Baofeng dealer or the manufacturer directly.

Manufacturer Contact Information:

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com

Print version: W31_EU V2.0

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.