Introduction
Thank you for purchasing the BAOFENG UV-32 Series Amateur Radio. This easy-to-use radio features dual band, dual display, and dual watch capabilities, providing secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.
Important Safety Information
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
Notice to Users (ISED): The operation of your Baofeng radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government's department of Innovation, Science, and Economic Development Canada (ISED). ISED requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.
RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios:
CAUTION: This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide that comes with the radio. This guide contains operating instructions for safe usage, RF energy awareness, and control for compliance with applicable standards and regulations. Any modification to this device, not expressly authorized by Baofeng, may void the user's authority to operate this device.
Under Innovation, Science, and Economic Development Canada (ISED) regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Innovation, Science, and Economic Development Canada (ISED) to operate with Baofeng-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/ controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
Precautions for Portable Terminals:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
Precautions for Batteries:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
Package Contents
The BAOFENG UV-32 transceiver comes shipped with the following items:
- 1 Radio body
- 1 Li-ion battery pack
- 1 Instruction Manual
- 1 Antenna
- 1 Power Adapter
- 1 Radio Case (optional)
- 1 Desktop Charger
- 1 Charging Cables (Type-C)
- 1 Clip

Features
- 2.0" TFT large color screen with full keyboard and fully open menu operation.
- GPS positioning function for accurate location tracking, sharing, and requesting location information.
- Bluetooth APP for wireless programming (Read and write radio data).
- 10 zones storage, up to 1000 named memory channels.
- High/Middle/Low power selectable (10W Tri-power).
- Scanner function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, scan channel addition and removal.
- Built-in input method for editing channel names.
- NOAA Weather Radio Channel Reception (for North American countries and territories only).
- Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K.
- Type-C direct charging and charging stand for convenient battery life.
- Dual-band handheld transceiver.
- High Capacity Lithium-Ion battery (2500mAh).
- Alarm function.
- Function beep on the keyboard.
- One touch search frequency.
- VOX (voice activated transmit).
- Broadcast FM radio receiver 78-108 MHz.
- Display illumination programmable via keypad.
- Dual watch / Dual reception.
- Two (2) pins for Kenwood accessory port.
- Scanning receiver frequency range: FM 76-108 MHz; AM 108-136MHz, VHF 136-174MHz, 220-260MHz, UHF350-390MHz, 400-520MHz.
- Intelligent Noise Reduction.




Setup
Battery Installation/Removal
Installing the Battery Pack:
- Position the battery pack over the back of the radio.
- Engage the battery pack into the radio until it is fully seated into the radio housing.
- Tighten the screws using a coin or suitable object to secure the battery pack to the radio. Do not overtighten.
To Remove Battery Pack from Radio:
- Loosen the screws on the back of the battery pack.
- Lift the bottom of the battery pack slightly to remove it from the radio housing.
- Pull the battery pack out of the radio housing.
Antenna Installation/Removal
Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
Removing the Antenna: Turn the antenna counter-clockwise to remove it.
Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity will reach its best performance.
Please use the specified charger provided by Baofeng. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a red flashing lamp or voice prompt, please charge the battery.
Using the Type-C Charger: The Type-C charger is a handy port that allows you to conveniently charge your Li-ion battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C cable into the Type-C charging port on your battery. Connect the other end of the Type-C charger to a wall power outlet.
- An empty battery will be fully charged in approximately 6 hours.
- The battery indicator light illuminates to indicate that the battery is charging.
LED Indicator Status:
| Red LED | Green LED | Status |
|---|---|---|
| Flashing | Steady | Standby (charger empty) Error (charger with radio) |
| Steady | Off | Charging |
| Off | Steady | Charge complete. |

Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
Radio Overview and Basic Operations
Radio Components

The UV-32 features a clear 2-inch color LCD screen and a full numeric keypad for easy operation. Key components include:
- Antenna
- Encoder/channel selector switch
- TX_RX status indication
- Power/Volume knob
- 2" color LCD screen
- PTT key
- Side key (SK1) - short press for custom function, long press for emergency alarm
- Side Key (SK2) - Sweep/Monitor
- Numeric keypad
- Built-in Microphone
- Charge contact
- Speaker
- Accessory port
- Type-C charging port
LCD Icon Summary
| Icon | Description |
|---|---|
| Battery level indicator | |
| DTMF side tone enabled | |
| D | Dual watch enabled |
| V | VOX enabled |
| * | Bluetooth frequency writing function activated |
| GNSS function enabled | |
| Keypad lock enabled | |
| ZONE01 | Indication of the current channel's region. Working in storage mode |
| VFO | In the current working VFO mode. Allow manual frequency input |
| A | A displays (upper section) and emission level indication |
| B displays (lower section) and emission level indication | |
| H | Transmit power level indicator, According to Power High |
| M | The current transmission power is medium power (used in normal environments). |
| Transmit power level indicator, According to Power Low | |
| DCS enabled | |
| CTCSS enabled | |
| Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. | |
| R | Reverse function enabled |
| T | Talkaround has been activated, off grid at the central turntable. The transmission frequency is equal to the receive frequency |
| The confidential calling feature is activated | |
| N | Narrowband enabled |
Main Keypad Controls
- MENU Key: Used for activating the MENU, choosing each MENU selection, and confirming parameters. In standby mode, press and hold to switch between frequency (VFO) mode and channel (MR) mode. When listening to broadcast FM, it switches between 65-75 MHz and 76-108 MHz bands.
- Up Arrow Key (▲): Press for more than 2 seconds to move channel and frequency upwards rapidly; in SCAN mode, moves scanning upwards.
- Down Arrow Key (▼): Press for more than 2 seconds to move channel and frequency downwards rapidly; in SCAN mode, moves scanning downwards.
- EXIT Key: Press to exit the Menu and functions. Press and hold to activate the frequency sweep function.
- P1 Key: Enter position mode, display position text information.
- P2 Key: Enter the coordinate mode of position.
- Numeric Keypad: Used to input information or selections.
- Asterisk Key (*): When there is a frequency difference between reception and transmission, press this key to activate the frequency reversal and talkaround functions. To enable or disable keypad lock, press and hold for about two seconds.
- Zero Key (0): Press and hold to activate the NOAA weather forecast reception function.
- Hash Key (#): When listening to broadcast FM, a momentary press will start scanning. To enable the scanner, press and hold for about two seconds.
Power On/Off
To turn the unit on: Simply rotate the Volume/Power knob clockwise until you hear a "click". If your radio powers on correctly, there should be an audible double beep after about one second, and the display will show a message or flash the LCD depending on settings. Then it will display a frequency or channel. If Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
To turn the unit off: Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
Adjusting the Volume
To turn up the volume, turn the volume/power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off. By using the monitor function, enabled from the [VOX/ Monitor] key below the PTT, you can more easily adjust your volume by adjusting it to the un-squelched static.
Main Band/Sub Band Switch
In standby mode, press the
key to switch between the main frequency band or sub frequency bands. The band with the larger display font is the primary band and the band with the smaller font is the secondary band.
VFO/Channel Switch
Press and hold the
key to switch between VFO and channel display.
- In channel mode (MR), the channel number will be displayed.
- In frequency mode (VFO), the VFO will be displayed.
Frequency (VFO) Mode
In Frequency (VFO) mode you can navigate up and down the band by using the
or
keys, according to the frequency step you've set. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offence. However, it is legal in most jurisdictions to listen.
Channel (MR) Mode and Channel Selection
There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is generally more practical. In Channel (MR) mode you can navigate up and down the channel by using the
or
keys or the encoder.
Select a Bank
A bank is a group of channels with the same property. The radio supports up to 10 banks, with a maximum of 100 channels per bank. To select a bank, press the
key, go to Menu > Bank, press
or
to select a bank, and then press
key to switch to the selected bank.
Making a Call
Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Making a call, the red LED is on.
Frequency mode call: Press and hold
key to switch to the frequency mode, input the working frequency within the allowable frequency range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with normal tone. Making a call, the red LED is on.
Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on.
Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help. To activate the emergency alert function, press and hold the [SK1] key for 3 seconds. The radio will send out a loud siren sound and the flashlight will flash. Press the SK1 (FM radios/Emergency) key to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
FM Radio (FM)
The frequency ranges to listen to the radio is 65-108MHz. When listening to broadcast FM, press
key switches between 65-75 MHz and 76-108 MHz band.
- In frequency or channel mode, Press [SK1] key to turn on the radio.
- Select the desired radio frequency with the
or
keys or input the frequency. Or Press # to automatically search a radio station. - Press [SK1] key to exit FM radio.
Monitor
In standby, press and hold the [SK2] key to enter Monitor. When receiving matched carrier but the signaling or the signal is too weak, this function allows monitoring of weak signals. Stop pressing the [SK2] key to turn off the speakers and return to standby mode.
Keypad Lock
The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the
key for about two seconds. You can also enable automatic keypad lock after ten seconds from the menu.
Frequency Reversal and Talkaround
When there is a frequency difference between the receiving frequency and the transmitting frequency, the radios operate in relay mode. A short momentary press of the
key enables the reverse function. If you want to listen to the repeater's input frequency instead, press
key momentarily and you'll reverse your transmit and receive frequencies. The channel attribute bar will display R. Press the
key again to switch the radio to talkaround mode, and the receiving frequency is equal to the transmitting frequency. The channel attribute bar will display T.
TX Repeaters Tone
Press [PTT] + [SK1] key to send 1750Hz repeaters tone. This function is useful for communications through repeaters.
One Touch Frequency Search
- Through the CPS program software or the radio menu >> Radio Setting >> Press the [SK1] key to define the [SK1] side key as a Search function.
- The radio will act as a receiver. Briefly press the preset 'Search' key, and the screen will display "SEARCH SEEK..."
- If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed, and if there is no CTCSS or DCS, NONE is displayed.
- You can press the
key to save the Search frequency and CTCSS or DCS to the channel.


Advanced Features
Scanner
The radio features a built-in scanner for the VHF and UHF bands. When in Frequency (VFO) mode it will scan in steps according to your set frequency step. In Channel (MR) mode it will scan your channels. To enable the scanner, press and hold the # key for about two seconds. You can change the scanning direction with the
or
keys. Press and hold the # key to exit scanning mode.
Frequency Ranger: In frequency mode, the frequency sweep range can be precisely set. Input the start value and end value of the sweep frequency through the keyboard.
Scan Modes: The scanner is configurable to one of three ways of operation: Time, carrier or search.
- Time operation (TO): The scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
- Carrier operation (CO): The scanner stops when it detects a signal, and after a factory preset time with no signal it resumes scanning.
- Search operation (SE): The scanner stops when it detects a signal. To resume scanning you must press and hold the # key again.
Scan Sub-Code (CTCSS/DCS): To search for a CTCSS or DCS code, in VFO mode, enter a known frequency, then use the menu to access "Scan Sub-Code" and initiate the scan. When a valid code is found, it will be displayed and the speaker will turn on.
Dual Watch
The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors. To enable or disable Dual Watch mode, press the
key to enter the main menu, enter [4] for Radio Settings, then enter [16] for 15 Dual Watch, and press
to select.
Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies. The radio has 10 zones, with a maximum of 100 channels stored in each zone. Each channel can store: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier or channel name.
In standby mode, press and hold
key to switch between frequency (VFO) mode and channel (MR) mode.
Repeaters Programming
To program repeaters, ensure you know the transmit and receive frequencies and are authorized to use them. In VFO mode, enter the repeater's output (receive) frequency, then use the menu to set the offset frequency and direction (positive or negative). Save the settings to memory.
GPS Function
The UV-32 is equipped with a multi-mode GPS module, including GPS from the United States and Beidou from China. In GPS mode, you can view location information but cannot make normal calls; voice intercom requires exiting GPS mode.
GPS On/Off Settings: Navigate to Menu > GNSS > GPS On/Off and select ON/OFF. The screen displays the
icon when the position system is active.
Time Zone Settings: Navigate to Menu > GNSS > Time Zone to select the correct time zone.
GPS Mode Settings: Navigate to Menu > GNSS > GPS Mode to select GPS mode (BDS, GPS, or GPS+BDS).
Use of GPS: In standby mode, press [P1] key to enter GPS mode and display "My Place" as an information list. Press [P2] to enter GPS mode and display the coordinate interface. Press
key to switch between My Place in the information list mode or electronic compass mode.
Find My Place: Press [P1] key to enter GPS mode, use the
key to switch to "My Place". The GPS will display "Searching..." (red GPS character) until positioning is successful, then "Searching Successful" (green GPS character) with current time, longitude, latitude, and altitude.
Share My Place Information: After successful GPS positioning, press the
key to switch to the location information interface, select the desired member sequence, and press [PTT] key to share.
Requesting Someone Else's Place: After successful GPS positioning, press the
key to switch to the My Place information interface, select the desired member sequence, and press [PTT] key to initiate a position request command.

Bluetooth Write Frequency
You can read and write frequency through Bluetooth. Before Bluetooth read/write frequency, you need to download and install the BAOFENG radio APP on your Android or iOS phone.
- Press
+ [3] to enter Bluetooth frequency writing. - Press
+
or
to select "On"; the
icon will be displayed on the first line of the screen.
Download BAOFENG radios APP: Use your Android phone to download and install the BAOFENG radios APP. After the APP is opened, allow Bluetooth and open the positioning function, select the brand Baofeng in the APP, select the model UV32 Pro Series, connect the radios, click radios, prompt the connection success and return to the homepage, then you can read and write the frequency.
Read Frequency: After completing the frequency reading, click the program to enter the program details. In the program details interface you can program channel information, frequency mode, optional functions.
Save Profile: The programmed scheme allows you to save it as a new profile and name the new profile.
Write Frequency: Tap Home, select Program, tap Write Frequency to enter Write Frequency, the radio will restart automatically after finishing Write Frequency.

Maintenance
Battery Maintenance
- Only charge batteries in normal room temperatures.
- When charging a battery attached to the radio, turn the radio off for a faster charge.
- Do not unplug the power to the charger or remove the battery and/or radio before it's finished charging.
- Never charge a wet battery.
- Batteries wear out over time. If you notice a considerably shorter operating time with your radio, please consider purchasing a new battery.
- Battery performance will be reduced in temperatures below freezing. When working in cold environments, keep a spare battery on you.
- Dust can interfere with the contacts on the battery. If necessary, wipe the contacts with a clean cloth.
How to Store the Battery
- If the battery needs to be stored, keep it in a 80% discharged status.
- It should be kept in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- To avoid severe capacity degradation, cycle the battery at least every six (6) months.
Troubleshooting
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. |
| During receiving, the voice is weak or intermittent. | The battery voltage maybe low. The volume level may be low. The antenna maybe loose or maybe installed incorrectly. | Recharge or replace the battery. Increase the volume. Turn off the radio, and then remove and reattach the antenna. |
| The speaker maybe blocked. | Clean the surface of the speaker. | |
| You cannot communicate with other group members. | The frequency or signaling type maybe inconsistent with that of other members. You may be too far away from other members. | Verify that your TX/RX frequency and signaling type are correct. Move towards other members. |
| You may be interrupted by radios using the same frequency. | Change the frequency, or adjust the squelch level. | |
| You hear unknown voices or noise. | The radio in analog mode maybe set with no signaling. | Request your dealer to set signaling for the current channel to avoid interference. |
| You may be too far away from other members. | Move towards other members. | |
| You are unable to hear anyone because of too much noise and hiss. | You may be in an unfavorable position. For example, your communication may be blocked by high buildings or in an underground area. It may be the result of external disturbance (such as electromagnetic interference). | Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. |
| The radio keeps transmitting. | VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
Specifications
| GENERAL | |
|---|---|
| Channel Capacity | 1000 / 10 Bank |
| Channel Spacing | 25.0 KHz / 12.5 KHz |
| Input Voltage | 7.4 VDC |
| Battery Life (5% TX, 5% RX, 90% Standby) | Li-on: 18 hours @ 5 watts |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 182×67×41mm (Not including antenna) |
| Radio Weight | 350 g (with Li-ON battery) |
| Material | Plastic |
| Waterproof / Water-Resistant | No |
| FCC ID | 2AJGM-NA32UV |
| TRANSMITTER | |
| Frequency Range (TX) | 144 to 148 MHz, 420 to 450 MHz (America version) 144 to 148 MHz, 430 to 450MHz (Canadian version) 144 to 146 MHz, 430 to 440MHz (European Union version)* |
| Modulation | 16K0F3E/11K0F3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
| RECEIVER | |
| Frequency Range | FM76-108MHz; AM108-136MHz; VHF: 136-174 MHz; 220-260MHz; UHF:350-390MHz; 400-520 MHz; |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 0.75 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
NOTE: All specifications may be modified without prior notice or liability. Thank you.


User Tips
- The UV-32 is easily configurable with CHIRP software for advanced programming.
- For extended range, consider using a longer antenna.
- The built-in GPS function works wonderfully for location tracking.
- A programming cable can be useful for full functionality and easier setup, especially if the included software is outdated.
- Be aware of legal transmission power limits in your region. The UV-32 can transmit up to 10 watts, which may exceed limits for license-free bands like PMR446 (0.5 Watt ERP). Ensure proper configuration to comply with local regulations.
- Use the official BAOFENG radio APP for Bluetooth programming on your smartphone.
- The UV-32 is NOT waterproof or water-resistant, so take precautions in wet environments.
Warranty and Support
EU Declaration of Conformity: Baofeng and Pofung hereby declare that the radio equipment type listed in Technical Specifications is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following link: http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC.
For further support, you can contact your local Baofeng helpdesk, your dealer from whom you purchased this radio, or send an email to wangjianhui@baofengradio.com.
A full PDF version of this manual is available for download here.