BAOFENG UV-9R PRO

Contents

Baofeng UV-9R PRO Series Amateur Radio User Manual

Your guide to secure, instant, and reliable communications.

1. Introduction

Thank you for purchasing the UV-9R PRO Series Amateur Radio. This easy-to-use radio offers dual band, dual display, and dual watch capabilities, ensuring secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to derive maximum performance from your radio.

This manual is applicable to the following products: UV-9R Plus, WP-9R, and AR-9 Radio.

1.1 Main Features

  • Frequency range: FM radio 76-108 MHz; AM aviation frequency band: 108-136MHz (RX)
  • VHF1: 136-174MHz (RX&TX); UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX)
  • VHF and UHF bands and channel name displayed
  • One touch frequency Search
  • 50 CTCSS tones and 210 DCS codes
  • SOS Emergency function
  • VOX, Scan, Dual Watch functions
  • Channel spacing: 25 KHz/12.5KHz
  • TOT (Time out timer)
  • Reverse function
  • CTCSS and DCS codes research
  • Busy Channel Lockout function (BCL)
  • Frequency step: 2.5/5/6.25/10/12.5/25KHz
  • Repeater shift
  • VOICE: vocal indication of the function selected
  • Power Save
  • Operating modes: UHF/VHF, UHF/UHF, VHF/VHF
  • Up to 128 memory channels
  • 1750Hz tone for repeaters
  • LCD display with backlight adjustable in 3 colors
  • 328 Motorola accessory jack
  • Channel or frequency mode selection
  • DTMF function
  • Alarm function
  • Setting and storing of channel names
  • High/Middle/Low power selection
  • Frequency offset (adjustable): 0-69.990MHz
  • Squelch adjustable in 9 levels
  • Keypad lock
  • Li-Ion 1800mAh battery pack

1.2 Package Contents

The package should contain the following items:

  • 1 x Radio unit
  • 1 x Li-Ion battery pack
  • 1 x Fast desktop charger
  • 1 x Wall adaptor
  • 1 x Belt clip
  • 1 x Antenna
  • 1 x User Manual (PDF) - View PDF

If any item is missing, please verify with your BAOFENG dealer.

Baofeng UV-9R PRO Walkie Talkie and its included accessories: Antenna, Battery, Clip, Lanyard, and User Manual.
Baofeng UV-9R PRO Walkie Talkie with included accessories.

2. Safety and Regulatory Information

2.1 Important Warnings

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ATTENTION! When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

2.2 RF Exposure Compliance and Control

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:

Guidelines:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.

Operating Instructions:

  • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
  • Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
  • Contact your local dealer for the product's optional accessories.

2.3 Precautions for Portable Terminals

Operating Prohibitions:

  1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips:

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Please operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
  • Handle the product with care.
  • Do not disassemble, modify or repair the product and its accessories without authorization.

2.4 Transportation Instructions

  • Damaged batteries must not be transported.
  • To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  • The radio must be switched off and secured against switch-on, if the battery is attached.

The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.

3. Setup and Installation

3.1 Charging the Battery

The Li-ion battery pack is not charged at the factory; please charge it before use. For best performance, fully charge and discharge the battery two or three times before regular use.

Charger Supplied:

Use only the specified charger provided by Baofeng. Other chargers may cause explosion and personal injury. If the radio displays low battery, charge it immediately.

Precautions for Li-ion Battery:

  • Do not short the battery terminals or throw the battery into a fire.
  • Charge the battery between 5°C-40°C (40°F - 105°F).
  • Turn off the radio before charging.
  • Do not interrupt the charging cycle until the green light is on.
  • Do not recharge a fully charged battery.
  • Dry a damp battery or radio before charging.

WARNING! When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

How to Charge:

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange.
  2. Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light turns red.
  3. A full charge takes approximately 2-5 hours. When the light turns green, charging is complete. Remove the battery or radio.

LED Indicator Status:

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

NOTE: Trouble means battery too warm, battery short-circuited or charger short-circuited.

3.2 Installing/Removing the Antenna

  • Installing: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

3.3 Installing the Belt Clip

  1. Install fixing head: Install the random belt clip fixing head in the slot on the back of the two-way radio and tighten the screws.
  2. Insert rotating belt clip: Slide the fixed head of the machine along the guide of the rotating back clip until you hear a "click" sound.
  3. Remove belt clip: Use the key to press the disassembly engine upwards until it releases, then push the belt clip with your thumb until it is removed.
Diagram showing belt clip installation steps.
Belt clip installation diagram.

3.4 Installing the Battery Pack

Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

  1. Insert the two protrusions on the front of the battery into the notches on the bottom of the radio.
  2. Press the tail of the battery toward the radio until you hear a "click".

Removing the Battery Pack:

Turn off the radio. Lift the battery push button at the end of the battery in the direction indicated by the arrow to disengage the tail of the battery from the intercom and remove the battery backwards.

Diagram showing battery pack installation and removal.
Battery pack installation and removal diagram.

3.5 Installing Additional Speaker/Microphone (Optional)

  1. Use a flat-blade screwdriver to unscrew the screw at the lower end of the cover counterclockwise to remove the headset cover.
  2. Insert the protruding part of the lower end of the headset into the slot indicated by the arrow in the figure below, then align the nut on the upper end of the headset with the corresponding threaded hole of the transceiver and rotate it clockwise until it is tightened.

NOTE: Please install accessories correctly; otherwise the waterproof performance of this product may be affected.

4. Operating Instructions

4.1 Radio Overview: Buttons and Controls

Detailed diagram of the Baofeng UV-9R PRO Walkie Talkie with numbered parts: Antenna, PTT, SK-Side key1/F, SK-side key2/M, Keypad, Knob (NO/OFF, Volume), Speaker, Accessory Jack, Microphone, LCD, Strap Buckle, Battery Latch, Flashlight, LED Indicator. Dimensions: 65x41.5x133.8mm.
Baofeng UV-9R PRO: Buttons and Controls.
  1. Antenna
  2. LED: transmission (red); reception (green)
  3. Flashlight
  4. SOS: Press for 5 seconds to activate alarm mode.
  5. Power / Switch / Volume control: Rotate to switch on/off and adjust volume.
  6. Speaker
  7. Microphone
  8. LCD display
  9. EXIT: Press to exit Menu and functions. A/B (appears on display): push to select desired frequency (VHF or UHF).
  10. #: Keypad lock. Long pressure: keypad will be locked. Short pressure: high or low power selection.
  11. PTT (Push-to-Talk)
  12. SK1: Press to activate FM radio. Press and hold for One touch frequency Search.
  13. SK2: Long press to activate Monitor function. Short press turns flashlight on.
  14. ▲/▼ keys: to select functions/menu.
  15. MENU: enter MENU functions and confirm selection. In off state, press and hold to turn on radio, allowing switching between frequency mode or channel mode.
  16. *SCAN: Reverse frequency/SCAN. Press to activate Reverse frequency; keep it pressed to activate SCAN function.
  17. MIC/SP: External speaker/mike jacks.
  18. 1800mAh Li-Ion battery pack.
  19. Battery release latch.

4.2 LCD Display

LCD Display of Baofeng UV-9R PRO showing frequency, channel, and status icons.
LCD Display with indicators.
  1. These symbols show that you set a DCS or CTCSS code in tx or rx. In tx mode it appears while you are transmitting, while in rx mode it is shown also in stand-by condition.
  2. Received signal strength.
  3. Low power selection.
  4. This letter is displayed when the Dual Watch function is active.
  5. VOX function enabled.
  6. Appears when a positive shift is activated.

4.3 Status Indications

The status LED has a very simple and traditional design:

  • Constant Red: Radio is transmitting.
  • Constant Green: Radio is receiving.

4.4 Basic Operations

Power On/Off:

  • Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". An audible double beep and display flash indicate power-on. The display will show a frequency or channel. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • Turning the unit off: Turn the volume/power knob counter-clockwise all the way until you hear a "click".

Adjusting the Volume:

Rotate the volume/power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far to avoid accidentally turning off the radio.

Making a Call:

NOTE: Press the [EXIT] key to switch the main channel if two channels are shown on the display. In the off state, press and hold the [MENU] key to turn on the radio; it will switch between frequency mode or channel mode.

  • Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with normal tone. The red LED will be on.
  • Frequency mode call: In the off state, hold press [MENU] key to open the radio, switching to the frequency mode. Enter the frequency range, then press the [PTT] key to initiate a call. Speak into the microphone with normal tone. The red LED will be on.
  • Receive a call: Release the [PTT] key to answer. The green LED will be on when receiving a call.

NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.

Channel Selection:

There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode.

  • Frequency (VFO) mode: Used for temporary frequency assignment and programming channels into memory. You can navigate up and down the band using the ▲ and ▼ keys, or input frequencies directly on the numeric keypad.
  • Channel (MR) mode: Used for selecting preprogrammed channels. You can navigate up and down channels using the ▲ and ▼ keys.

WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on unauthorized frequencies is illegal and a serious offense.

4.5 Advanced Features

Frequency Scanning:

In frequency mode, press [*SCAN] key for more than 2 seconds. The radio will start scanning frequencies according to the set frequency step. You can change the scanning direction with the ▲ and ▼ keys. Press any key to stop scanning.

Channel Scanning:

In channels mode, press [*SCAN] key for more than 2 seconds. The radio will start scanning channels. You can change the scanning direction with the ▲ and ▼ keys. Press any key to stop scanning.

Search CTCSS/DCS Code:

This function allows you to search and store the CTCSS/DCS code used by other radios.

  1. In frequency mode, press [MENU]+[1][1].
  2. Press [MENU] key again.
  3. Press [*SCAN] key; CT will blink on the display.
  4. When another radio is transmitting, the display will show the CTCSS/DCS code.
  5. After searching, the radio will beep and stop scanning.
  6. Press [MENU] key for confirmation and store, or press [PTT] or [EXIT] key to return to standby mode.

NOTE 1: The DCS scanning has the same procedure as CTCSS code, but you have to select MENU+10 to enter scanning.

Example of One Touch Frequency Search display showing 'SEARCH UHF' and a found frequency with DCS code.
One Touch Frequency Search display example.

Cursor Conversion (A/B):

Directly press [EXIT] key to move the cursor up and down. You can modify or confirm parameters indicated by the cursor. The UV-9R PRO has a dual-frequency display function. In frequency mode, you will see two different receiving and transmitting frequencies; in channel mode, two different channels will be displayed. Press [EXIT] to shift between main channel A and sub-channel B.

High/Mid/Low Power Fast Selection:

In channel mode, press [#] key to shift between high/low power.

Keypad Lock:

This function locks the keypad to prevent accidental pressure. To unlock, press [#] for more than 2 seconds.

FM Radio (FM):

The frequency range to listen to is 65-108MHz. When listening to broadcast FM, press [EXIT] key switches between 65-75 MHz and 76-108 MHz band.

  1. In frequency or channel mode, Press [SK1] to turn on the radio.
  2. Select the desired radio frequency with the ▲ or ▼ keys or input the frequency. Or Press [* SCAN] to automatically search a radio station.
  3. Press [SK1] to exit FM radio.

Note: While listening to the radio, the frequency or channel of A/B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will automatically switch again to FM radio mode.

Flashlight:

This function is useful for night illumination. To turn it on, press [SK2]; push it again for strobe mode; push it again to turn it off.

TX 1000Hz, 1450Hz, 1750Hz, 2100Hz Repeaters Tone:

Press [PTT] + [SOS] to send 1750Hz repeaters tone. This function is useful for communications through repeaters. If keypad lock is enabled, you can still send a 1750Hz tone.

4.6 Manual Programming (Channels Memory)

Memory channels are an easy way to store commonly used frequencies. The Baofeng UV-9R PRO features 128 memory channels that can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier or channel name.

Frequency Mode vs. Channel Mode:

In the off state, press and hold the [MENU] key to turn on the radio; it will switch between frequency mode or channel mode. These two modes have different functions and are often confused.

  • Frequency Mode (VFO): Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.
  • Channel Mode (MR): Used for selecting preprogrammed channels.

Example 1: Programming a Channel Repeater Offset with CTCSS Tone

To program a new memory in Channel 10 with RX = 432.000 MHz, TX = 437.000 MHz (+5 Offset), and TX CTCSS tone 123.0:

  1. Turn off the radio.
  2. Hold press [MENU] key to open the radio, switching to frequency mode. Channel number at the right will disappear.
  3. [MENU] > [2][8] > [MENU] > [1] > [0] > [MENU] > [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] > [1][3] > [MENU] > 123.0 > [MENU] > [EXIT] (Selects desired TX encode tone)
  5. Enter RX frequency (e.g., 432000)
  6. [MENU] > [2][7] > [MENU] > [1][0] > [MENU] > [EXIT] (Enter the desired channel 10, RX has been added)
  7. Enter TX frequency (e.g., 437000)
  8. [MENU] > [2][7] > [MENU] > [1][0] > [MENU] > [EXIT] (Enter the same channel 10, TX has been added)
  9. In the off state, press and hold the [MENU] key to turn on the radio to return to MR mode, and the channel number will reappear.

Example 2: Programming a Simplex Channel with CTCSS Tone

To program a new memory in Channel 10 with RX = 436000 MHz and TX CTCSS tone 123.0, follow similar steps as above, adjusting for simplex operation.

4.7 Repeaters Programming

The following instructions assume you know your repeater's transmit and receive frequencies and are authorized to use it.

  1. Turn off the radio. Press and hold the [MENU] key to turn on the radio and return to frequency (VFO) mode.
  2. Use the numeric keypad to enter the repeater's output (your receiving) frequency.
  3. Press the [MENU] key to enter the menu.
  4. Enter [2][6] on the numeric keypad to get to frequency offset.
  5. Press [MENU] key to select.
  6. Use the numerical keypad to enter the specified frequency offset.
  7. Press [MENU] to confirm and save.
  8. Enter [2][5] on the numeric keypad to get to offset direction.
  9. Use the ▲/▼ keys to select + (positive) or - (negative) offset.
  10. Press [MENU] to confirm and save.
  11. Optional: Save to memory, set up CTCSS.
  12. Press [EXIT] to exit the menu.

NOTE: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the Baofeng UV-9R PRO, see the section called "1750Hz Tone-burst".

  1. The radio will act as a receiver. Press and hold the [SK1] key, and the screen will display "SEARCH UHF".
  2. If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed, and if there is no CTCSS or DCS, NONE is displayed.
  3. You can press the [MENU] key to save the Search frequency and CTCSS or DCS to the channel.

Note: During frequency Search, press the [#] key on the radio to switch between UHF or VHF bands.

4.9 Working the Menu System

For a complete reference on available menu items and parameters, see Appendix C, Shortcut Menu operations (pages 30-33 of the PDF manual).

Basic Use:

  1. Press the [MENU] key to enter the menu.
  2. Use the [▲] and [▼] keys to navigate between menu items.
  3. Once you find the desired menu item, press [MENU] again to select that menu item.
  4. Use the [▲] and [▼] keys to select the desired parameter.
  5. To confirm your selection, press [MENU]. To cancel changes, press [EXIT].
  6. To exit the menu at any time, press the [EXIT] key.

Using Shortcuts:

Every menu item has a numerical value. These numbers can be used for direct access.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] key.
  4. For entering the desired parameter, use arrow keys or numerical keypad.
  5. To confirm your selection, press [MENU]. To cancel changes, press [EXIT].
  6. To exit the menu at any time, press the [EXIT] key.

Functions and Operations (Menu No. 0-41):

  • (1) Squelch level (SQL) - MENU No.0: Adjust squelch in 10 levels (0=open, 9=highest).
  • (2) Step frequency (STEP) - MENU No.1: Select desired frequency step (2.5/5.0/6.25/10.0/12.5/20.0/25.0/50.0 KHz). Not modifiable in channel mode.
  • (3) Output power (TXP) - MENU No.2: Select high/middle/low output power. Low power reduces radiation and saves battery. Press "#" to switch.
  • (4) Battery save (SAVE) - MENU No.3: Reduces battery consumption in standby. 5 selections (OFF / 1:1 / 1:2 / 1:3 / 1:4).
  • (5) VOX Function (VOX) - MENU No.4: Enables hands-free conversations. 11 levels (OFF-10). Not modifiable in SCAN and FM radio mode.
  • (6) Wide/Narrow bandwidth (WN) - MENU No.5: Set working bandwidth (WIDE: 25KHz, NARROW: 12.5KHz). Not modifiable in channel mode.
  • (7) Backlight (ABR) - MENU No. 6: Adjust auto-off time of display backlight (1-5s).
  • (8) Dual Watch Operation (TDR) - MENU No. 7: Receive frequencies of channel A and B simultaneously.
  • (9) Keypad beep (BEEP) - MENU No. 8: Enables audible beep tone on key press.
  • (10) Time-Out-Timer (TOT) - MENU No.9: Prevents too long transmissions (15s, 30s, 45s, etc.).
  • (11) Receiving DCS (R-DCS) - MENU No.10: Set DCS codes for personal channels (D023N-D754N, D023I-D754I).
  • (12) Receiving CTCSS (R-CTCSS) - MENU No.11: Set CTCSS codes for private channels (50 groups).
  • (13) Transmitting DCS (T-DCS) - MENU No.12: Activate DCS codes in TX mode.
  • (14) Transmitting CTCSS (T-CTCSS) - MENU No.13: Set CTCSS tone in TX mode (67.0 to 254.1 Hz).
  • (15) Voice function (VOICE) - MENU No. 14: Activates voice prompts for operations.
  • (16) ANI-ID (ANI-ID) - MENU No.15: Set your ID-code (up to 5 digits, programmable by software).
  • (17) DTMFST (DTMFST) - MENU No.16: Determines when DTMF Side Tones are heard.
  • (18) Signal code (S-CODE) - MENU No.17: Selects 1 of 15 DTMF codes (programmed by software).
  • (19) SCAN Resume Mode (SC-REV) - MENU No.18: Choose scan resume behavior (TO: Time-operated, CO: Carrier-operated, SE: Search).
  • (20) PTT-ID (PTT-ID) - MENU No.19: Decide when to send ANI-ID code in TX mode (OFF, BOT, EOT, BOTH).
  • (21) PTT ID delay (PTT-LT) - MENU No.20: Set delay time (0-30ms) for sending PTT-ID.
  • (22) Channel A Display Mode (MDF-A) - MENU No.21: Set display mode for channel A (FREQ, CH, NAME).
  • (23) Channel B Display Mode (MDF-B) - MENU No.22: Set display mode for channel B (FREQ, CH, NAME).
  • (24) Busy Channel Lock (BCL) - MENU No. 23: Prevents transmission if channel is busy.
  • (25) Auto Keypad Lock (AUTOLK) - MENU No.24: Automatically locks keypad after 15s.
  • (26) Frequency offset direction (SFT-D) - MENU No.25: Set direction of frequency offset in RX and TX (+: Positive, -: Negative, OFF: no offset).
  • (27) Frequency offset (OFFSET) - MENU No. 26: Set deviation between TX and RX (0-69.990MHz).
  • (28) Channel store (MEM-CH) - MENU No. 27: Store current frequency/parameters to a channel (0-127).
  • (29) Channel Delete (DEL-CH) - MENU No.28: Delete programmed information from a channel (0-127).
  • (30) Standby backlight (WT-LED) - MENU No.29: Choose backlight color in standby mode (OFF, BLUE, PURPLE, ORANGE).
  • (31) RX backlight (RX-LED) - MENU No. 30: Choose backlight color when receiving (OFF, BLUE, PURPLE, ORANGE).
  • (32) TX backlight (TX-LED) - MENU No.31: Choose backlight color when transmitting (OFF, BLUE, PURPLE, ORANGE).
  • (33) Alarm Mode (AL-MOD) - MENU No.32: Set tone alarm/code alarm/site alarm (SITE, TONE, CODE).
  • (34) Dual Watch (TDR-AB) - Menu No.34: Receive signals of A/B channel or frequency. Can be used for cross band receiving and transmitting.
  • (35) Side tone elimination (STE) - Menu No. 35: Eliminates annoying audio tone after transmission.
  • (36) Side tone elimination in communication through repeater (RP-STE) - Menu No. 36: Eliminates squelch tail noise when communicating through a repeater.
  • (37) Delay time of side tone elimination in communication through repeater (RPT-RL) - Menu No.37: Sets delay time for repeater squelch tail (1-10).
  • (38) Display mode at the turning on (PONMSG) Menu No.38: Set display mode when radio is turned on (FULL, MSG, ON).
  • (39) Roger beep (ROGER) - Menu No. 39: Sends an end-of-transmission tone.
  • (40) Reset (RESET) - Menu No.40: Resets transceiver to factory-programmed settings (VFO: Menu Reset, ALL: Menu and channel Reset).
  • (41) 1000Hz, 1450Hz, 1750Hz, 2100Hz Repeater Tone (R-TONE) - Menu No.41: Select repeater tone. To send, hold [PTT] + [SOS] key.

5. Maintenance

5.1 Battery Maintenance Instructions

To help your battery work normally or prolong its life, be sure to observe the following instructions:

  1. Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
  2. It is recommended to charge the battery under 5°C~40°C. Violation of this limit may cause battery life reduction or even battery leakage.
  3. To charge a battery attached to the product, turn it off to ensure a full charge.
  4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.

5.2 How to Store the Battery

  • If the battery needs to be stored, keep it in status of 80% discharged.
  • It should be kept in low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.
  • Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

6. Troubleshooting Guide

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent.The battery voltage maybe low.
The volume level may be low.
The antenna maybe loose or maybe installed incorrectly.
The speaker maybe blocked.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, and then remove and reattach the antenna.
Clean the surface of the speaker.
You cannot communicate with other group members.The frequency or signaling type maybe inconsistent with that of other members.
You may be too far away from other members.
You may be interrupted by radios using the same frequency.
Verify that your TX/RX frequency and signaling type are correct.
Move towards other members.
Change the frequency, or adjust the squelch level.
You hear unknown voices or noise.The radio in analog mode maybe set with no signaling.
You may be too far away from other members.
Request your dealer to set signaling for the current channel to avoid interference.
Move towards other members.
You are unable to hear anyone because of too much noise and hiss.You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area.
It may be the result of external disturbance (such as electromagnetic interference).
Move to an open and flat area, restart the radio, and try again.
Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.

7. Technical Specifications

FeatureSpecification
Frequency Range144.0-148.0 & 420.0-450.0MHz (Tx, FCC Rule parts 97 to USA users)
136.0-174.0 & 400.0-480.0MHz (Scanning Receiver, FCC Rule parts 15B to USA users)
144.0-146.0& 430.0-440.0MHz (Tx/Rx. Limited to EU users)
Memory Channel128 Groups
Operation VoltageDC 7.4 V ±10%
Battery Capacity1800mAh (Li-Ion)
Transmission current≤1800mA
Receive Sensitivity0.25µV (12dB SINAD)
Power Output1W @16 ohms
Receive current≤380mA
Rated Audio Distortion≤5%

ATTENTION! Operating frequency is divided into transmit and receive frequencies, please comply with the Radio Regulations in this country or territory.

8. Warranty and Support

8.1 Declaration of Conformity

Baofeng hereby declares that the radio equipment type listed in Appendix B is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.Baofeng.cn/download.asp?EnBigClassName=EU+DOC&EnSmallClassName=&page=3.

Via your local Baofeng helpdesk, your dealer from where you purchased this radio or send an email to wangjianhui@baofengradio.com.

8.2 Disposal of Electronic and Electric Equipment

Products with the symbol (crossed-out wheeled bin) cannot be disposed of as household waste. Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste by-products.

In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

WEEE symbol indicating separate collection for electrical and electronic equipment.
WEEE Symbol

8.3 Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.

We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

PO FUNG ELECTRONIC (HK) INTERNATIOANL GROUP COMPANY
Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong

9. User Tips

This section is typically populated with helpful tips derived from user reviews and Q&A. As no such data was provided, please refer to the main manual sections for detailed instructions.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.