1. Introduction
The JIKONG JK-B2A8S is an intelligent active balancer designed for 4S to 8S battery packs, compatible with Li-ion, LiFePO4, and LTO battery types. It features real-time, active energy transfer equalization to optimize battery performance and extend lifespan. This manual provides essential information for the safe and efficient use of your active balancer.

2. Key Features
- Real-time Active Balancing: Utilizes energy transfer equalization for optimal cell voltage.
- Wide Battery Compatibility: Supports 4S to 8S Li-ion, LiFePO4, LTO, and super capacitor battery packs.
- High Precision: Single cell voltage collection range of 1V ~ 5V with an accuracy of ±3mV.
- Adjustable Balance Current: Independently set balance current from 0.1A to 2A, irrespective of cell voltage difference.
- Smart Connectivity: Bluetooth communication with a dedicated mobile APP for real-time battery status monitoring.
- Safety Features: Equilibrium line resistance detection for early abnormal contact failure identification and low voltage shutdown to prevent battery damage.
- Protection Functions: Includes Overcharge Protection, Over Discharge Protection, Overcurrent Protection, and Short Circuit Protection.


3. Installation and Wiring
Proper installation and wiring are crucial for the safe and effective operation of the active balancer. Follow these steps carefully:
- Connect all cables: Ensure all necessary balance cables are prepared and correctly identified for your battery pack configuration.
- Insert cables into BMS: Carefully insert the balance cables into the designated ports on the JIKONG JK-B2A8S balancer.
- Connect B-line and P-line: Connect the B-line (battery negative) and P-line (pack positive) to your battery pack as per the wiring diagram.
Warning: Incorrect wiring can damage the balancer, battery, or pose a safety risk. Always double-check connections before powering on.

4. Operation
4.1 Mobile APP Control
The JIKONG JK-B2A8S features Bluetooth connectivity, allowing you to monitor and manage your battery system via the 'JIKONG BMS' mobile application. The APP supports iOS, Android, and HarmonyOS systems and can automatically switch to multiple languages based on your phone's settings.
With the APP, you can view various real-time battery parameters at a glance:
- Voltage (Overall and individual cell)
- Current
- Temperature
- State of Charge (SOC)
- Alarm status
- Battery Cycles
- Cells Wire Resistance

4.2 Parameter Adjustment
The APP allows you to freely adjust multiple protection values, including overcharge, overdischarge, overcurrent, temperature, and balance settings. Always refer to the internal parameters of the protection board first before making changes to ensure safe operation.
Note: If you require PC connectivity for advanced functions (e.g., RS485 or CANBUS), you would need a different balancer model as the JK-B2A8S does not support these features.

5. Maintenance
To ensure the longevity and optimal performance of your JIKONG JK-B2A8S active balancer, consider the following maintenance tips:
- Keep Connections Clean: Periodically inspect all wiring connections for corrosion or looseness. Ensure they are clean and securely fastened.
- Environmental Conditions: Operate the balancer within its specified temperature and humidity ranges. Avoid exposure to extreme heat, cold, or moisture.
- Software Updates: Check for updates to the JIKONG BMS mobile application regularly to benefit from new features and performance improvements.
- Visual Inspection: Occasionally inspect the balancer for any signs of physical damage or overheating.
6. Troubleshooting
If you encounter issues with your JIKONG JK-B2A8S active balancer, refer to the following common problems and solutions:
- Balancer Not Activating:
- Check all wiring connections to ensure they are secure and correctly installed according to the diagram.
- Verify that the battery pack voltage is within the operational range (4S-8S).
- Inaccurate Readings on APP:
- Ensure the balance cables are properly connected to each cell. The balancer features equilibrium line resistance detection to identify abnormal contact failures.
- Restart the mobile APP and re-establish the Bluetooth connection.
- Battery Damage Prevention:
- The balancer has a low voltage shutdown function to prevent over-discharge. If the battery pack is too low, it may not activate until a minimum voltage is reached.
- Overcharge/Over-discharge/Overcurrent Alarms:
- Check the APP for specific alarm details. These indicate that the battery pack has reached its set protection limits. Adjust charging/discharging behavior or review protection settings in the APP if necessary.
For persistent issues, contact JIKONG customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Model | JK-B2A8S |
| Battery Strings Supported | 4S-8S |
| Battery Types Supported | Li-ion, LiFePO4, LTO |
| Balance Method | Active Balance (Full State On) |
| Balance Current | 2A |
| Single Cell Voltage Range | 1V ~ 5V |
| Voltage Accuracy | ±3mV |
| Charging Current | 10A |
| Bluetooth Function | YES |
| APP Support | Android, iOS, HarmonyOS |
| RS485 Function | NO |
| CANBUS Function | NO |
| NTC (Temperature Detection) | NO |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
| Charge and Discharge Port | Common Port BMS |
| Dimensions (approx.) | 85mm (W) x 115mm (L) x 20mm (H) |

8. User Tips
Based on general user experiences with active balancers:
- Initial Balance: For new battery packs or packs with significant cell voltage differences, allow the balancer sufficient time (several hours to days) to perform its initial equalization. Monitoring via the APP is recommended during this period.
- APP Monitoring: Regularly check the mobile APP for any 'Alarm' notifications. Addressing these promptly can prevent potential issues.
- Cable Management: Ensure balance cables are neatly routed and secured to prevent accidental disconnections or damage.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the seller or JIKONG customer service directly. Keep your purchase receipt as proof of purchase.