1. Important Warnings
Thank you for purchasing this HOBBYWING product! Brushless power systems can be very dangerous. Any improper use may cause personal injury and damage to the product and related devices. We strongly recommend reading through this user manual before use. Because we have no control over the use, installation, or maintenance of this product, no liability may be assumed for any damages or losses resulting from the use of the product. We do not assume responsibility for any losses caused by unauthorized modifications to our product. Besides, we have the right to modify our product design, appearance, features and usage requirements without notification. We, HOBBYWING, are only responsible for our product cost and nothing else as result of using our product.
- Read through the manuals of all power devices and aircraft and ensure the power configuration is rational before using this unit.
- Ensure all wires and connections are well insulated before connecting the ESC to related devices, as short circuit will damage your ESC. Ensure all devices are well connected; in order to prevent poor connections that may cause your aircraft to lose control or other unpredictable issues like damage to the device. If necessary, please use a soldering iron with enough power to solder all input/output wires and connectors.
- Never get the motor locked up during high-speed rotation, otherwise the ESC may get destroyed and may also get your motor damaged. (Note: move the throttle stick to the bottom position to disconnect the battery immediately if the motor really gets locked up).
- Never use this unit in extremely hot weather or continue to use it when it really gets hot. Because high temperature will activate the ESC thermal protection or even damage your ESC.
- Always disconnect and remove batteries after use, as the ESC will continue to consume current if it's still connected to batteries. Long-time contact will cause batteries to completely discharge and result in damage to batteries or/and ESC. This will not be covered under warranty.
2. Features
- High performance 32-bit ARM M0 microprocessor (up to 120MHz) compatible with various brushless motors.
- DEO (Driving Efficiency Optimization) Technology improves throttle response, driving efficiency, and reduces ESC temperature.
- Separate program cable for connecting to a LED program box for easy setup and programming.
- Normal/reverse brake modes (with reverse brake mode) effectively shorten aircraft landing distance.
- Search mode helps locate aircraft by alarm beeps in complex environments.
- Multiple protection features: start-up, ESC thermal, capacitor thermal, over-current, over-load, abnormal input voltage, and throttle signal loss.
3. Specifications
| Model (Regular) | Cont. Current | Peak Current | Input Voltage | BEC Output | Weight | Size (L x W x H) |
|---|---|---|---|---|---|---|
| Skywalker 120A V2 | 120A | 150A | 3-8S LiPo | Switch Mode, Output: 5V/6V/7.4V/8.4V adjustable, Current cont./Peak 10A/30A | 117g | 83x35x22mm |
4. Setup
4.1 Connections
- Throttle Signal Cable (Long White/Red/Black Tri-color Cable): Plug into the TH channel on the receiver or flight controller. The White wire is for transmitter throttle signals, the Red & Black wires are BEC output wires.
- Reverse Brake Signal Cable (Short Yellow/Black): Must be plugged into any vacant channel on the receiver (when using the Reverse Brake mode) to control the ON/OFF of the Reverse Brake function.
- Programming Cable (Short White/Red/Black Tri-color Cable): Connect it to a LED program box if users want to program the ESC.
4.2 ESC/Radio Calibration
- Turn on the transmitter, move the throttle stick to the top position.
- Connect a battery to the ESC. The motor will sound "♪123" to indicate the ESC is normally powered on.
- The motor will then beep two short beeps to indicate the throttle top endpoint is accepted.
- Move the throttle stick to the bottom position within 5 seconds after the two short beeps. The minimum throttle position will be accepted 1 second later.
- The motor will beep "Number" beeps to indicate the number of LiPo cells you have plugged in.
- The motor will beep a long beep to indicate the calibration is complete.
Attention! The default throttle range of this ESC is from 1100us to 1940us (Futaba's standard); users need to calibrate the throttle range when they start to use a new SKYWALKER brushless ESC or another transmitter.
5. Operating Instructions
5.1 Normal Start-up Process
- Turn on the transmitter, and then move the throttle stick to the bottom position.
- After connecting the ESC to a battery, the motor will emit "♪123" indicating the ESC is normally powered on.
- The motor will emit several beeps to indicate the number of LiPo cells.
- The motor emits a long beep to indicate the ESC is ready to go.
6. ESC Programming
6.1 Programming with a LED Program Box
- Plug the programming cable (on your ESC) into the programming port on the LED program box.
- Connect a battery to your ESC. After powering a LED program box to the ESC, all programmable items will show up a few seconds later. (If the ESC is already connected to the battery, disconnect the battery and then reconnect it.)
- You can select the item you want to program and the setting you want to choose via "ITEM" & "VALUE" buttons on the program box, and then press the "OK" button to save all new settings to your ESC.
- Disconnect ESC and battery, then reconnect them, the ESC will start up and run with the new parameters.
6.2 Programming with the Transmitter
This method consists of 4 steps: Enter the programming → Select parameter items → Select parameter values → Exit the programming.
I. Enter the Programming
Turn on the transmitter, move the throttle stick to the top position, and connect a battery to the ESC. 2 seconds later, the motor will beep "B-B-" first, then emit a series of beeps (5-6-7-1-2) 5 seconds later to indicate that you are in the ESC programming mode.
II. Select Parameter Items
After entering the programming, you'll hear 12 kinds of beeps circularly. Move the throttle stick to the bottom position within 3 seconds after you hear some kind of beeps, you'll enter the corresponding parameter item.
| Items | Beep Type | Parameter |
|---|---|---|
| 1 | "B-" | Brake Type |
| 2 | "B-B-" | Brake Force |
| 3 | "B-B-B-" | Voltage Cutoff Type |
| 4 | "B-B-B-B-" | LiPo Cells |
| 5 | "B-B-B-B-B-" | Cutoff Voltage |
| 6 | "B-B-B-B-B-B-" | Start-up Mode |
| 7 | "B-B-B-B-B-B-B-" | Timing |
| 8 | "B-B-B-B-B-B-B-B-" | Active Freewheeling |
| 9 | "B-B-B-B-B-B-B-B-B-" | Search Mode |
| 10 | "B-B-B-B-B-B-B-B-B-B-" | BEC Voltage |
| 11 | "B-B-B-B-B-B-B-B-B-B-B-" | Factory Reset |
| 12 | "B-B-B-B-B-B-B-B-B-B-B-B-" | Exit |
Note: A long "B----" equals to 5 short "B-", so a long "B----" and a short "B-" represent the 6th item in "Select Parameter Items".
III. Select Parameter Values
The motor will beep different kinds of beeps circularly. Move the throttle stick to the top position after you hear some kind of beeps to select the corresponding parameter value. Then you'll hear the motor emit "1515" to indicate the value is saved, then get back to "Select Parameter Items" and continue to select other parameter items that you want to adjust.
| Items | Values | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
|---|---|---|---|---|---|---|---|---|
| 1 | Brake Type | *Disabled | Normal | Reverse | Linear Reverse | |||
| 2 | Brake Force | *Low | Medium | High | ||||
| 3 | Voltage Cutoff Type | *Soft | Hard | |||||
| 4 | LiPo Cells | Auto Calc. | 3S | 4S | 5S | 6S | 7S | 8S |
| 5 | Cutoff Voltage | Disabled | Low | Medium | High | |||
| 6 | Start-up Mode | *Normal | Soft | Very Soft | High | |||
| 7 | Timing | *Low | Medium | High | ||||
| 8 | Active Freewheeling | *On | Off | |||||
| 9 | Search Mode | *Off | 5min | 10min | 15min | |||
| 10 | BEC Voltage | 5V | *6V | 7.4V | 8.4V |
Note: Values marked with * in the table are the factory default settings.
IV. Exit the Programming
Move the throttle stick to the bottom position within 3 seconds after you hear two long and three short beeps. Disconnect the battery from the ESC. The motor will beep "Number" beeps to indicate the number of LiPo cells you have plugged in, and then a long beep to indicate the power system is ready to go.
7. Troubleshooting
| Troubles | Warning Tones | Causes | Solutions |
|---|---|---|---|
| ESC didn't work after it was powered on while the motor kept beeping. | "B, B, B..." | Input voltage beyond operating range. | Adjust power-on voltage to operating range. |
| ESC didn't work after it was powered on while the motor kept beeping. | "B-, B-, B-, B-" | ESC didn't receive throttle signal. | Check transmitter/receiver binding and connections. |
| ESC didn't work after it was powered on while the motor kept beeping. | "B, B, B, B..." | Throttle stick not at bottom position. | Move throttle stick to bottom and calibrate throttle range. |
| ESC didn't work after throttle calibration while the motor kept beeping. | "B, B, B, B..." | Throttle range set too narrow. | Re-calibrate throttle range. |
| ESC output suddenly reduced to 50% during flight; motor kept beeping after flight completed but battery still connected. | "BB, BB, BB..." | ESC thermal protection activated. | Improve heat dissipation (add cooling, fan) or reduce load. |
| ESC output suddenly reduced to 50% during flight; motor kept beeping after flight completed but battery still connected. | "BBB, BBB, BBB..." | Low-voltage cutoff protection activated. | Change battery pack, lower cutoff voltage or disable LVC protection (not recommended). |
7.1 Multiple Protections Details
- Start-up Protection: If the motor fails to start normally, the ESC will attempt to restart if throttle is less than 15%. If greater than 20%, move throttle stick to bottom and restart.
- ESC Thermal Protection: Reduces output power at 110°C, cuts off power if temperature continues to rise. Alarm sounds when throttle returns to 0%.
- Throttle Signal Loss Protection: Cuts off output immediately if throttle signal is lost for over 0.25 seconds to prevent damage. Resumes normal output when signal is restored.
- Over-current Protection: Cuts off power or restarts automatically if load suddenly increases (e.g., blocked propellers).
- Low-voltage Cutoff Protection: Triggers when battery voltage is below cutoff. Soft cutoff reduces power to 60%; hard cutoff immediately. Alarm sounds when throttle returns to 0%.
- Abnormal Input Voltage Protection: Triggers if battery voltage is outside supported input range. Alarm sounds.
8. User Tips
- Always perform a thorough pre-flight check and test all connections and calibrations before operating your aircraft.
- Ensure your battery is fully charged and in good condition to avoid low-voltage cutoff issues during flight.
- Regularly inspect all wiring for wear or damage to prevent unexpected signal loss or short circuits.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the official Hobbywing customer support channels. Please refer to the original product packaging or the manufacturer's website for the most up-to-date warranty terms and contact details.