Introduction
This manual provides detailed instructions for the safe and effective use of your Dragonhawk A1 Wireless Tattoo Pen Kit. Please read this manual thoroughly before operating the device to ensure optimal performance and longevity.
Figure 1: Dragonhawk A1 Wireless Tattoo Pen Kit, showing the pen, cartridges, inks, and accessories.
Setup
1. Unboxing and Initial Inspection
Carefully unpack all components from the box. Verify that all items listed in the "What's in the Kit?" section are present and undamaged.
Video 1: Unboxing and initial setup of the Dragonhawk A1 Wireless Tattoo Pen.
2. Charging the Device
Before first use, fully charge the tattoo pen. Connect the provided Type-C charging cable to the charging port on the top of the pen and plug the other end into a suitable USB power adapter (not included).
- Charging Time: Approximately 2-3 hours.
- The screen will display the battery level during charging.
Figure 2: Illustration of the Type-C charging port and battery capacity (1600mAh) with estimated working and charging times.
3. Attaching a Cartridge Needle
- Ensure the pen is powered off.
- Select the desired universal cartridge tattoo needle.
- Insert the cartridge into the cartridge interface at the front of the pen.
- Twist the cartridge clockwise gently until it is securely seated.
The Dragonhawk A1 is compatible with standard universal cartridge needles.
Operating Instructions
1. Power On/Off
- To Power On: Long press the power button. The screen will illuminate, displaying the current voltage and battery level.
- To Power Off: Long press the power button again.
2. Start/Pause Operation
- While the pen is powered on, short press the power button to start the needle movement.
- Short press the power button again to pause the operation.
3. Adjusting Voltage
- Use the "+" button to increase the voltage.
- Use the "-" button to decrease the voltage.
- The working voltage range is 5V to 12V.
4. Switching Modes (Dot Mode / Normal Mode)
The Dragonhawk A1 features two operating modes:
- To Switch Modes: Double-click the power button rapidly while the pen is powered on.
- Dot Mode: Indicated by 'd' followed by a number (1-9) on the screen. This mode is suitable for dot work. Adjust the dot mode level using the '+' and '-' keys.
- Normal Mode: Standard continuous operation.
Figure 3: Explanation of Dot Mode and Normal Mode switching via double-clicking the power button.
5. Adjusting Needle Depth
Rotate the grip of the tattoo pen to adjust the needle protrusion (depth) to your desired setting.
6. Recommended Operating Voltages
Optimal voltage settings can vary based on needle type and desired effect. Below are general recommendations:
| Needle Type | Size Range | Recommended Voltage |
|---|---|---|
| Round Liner (RL) | 1RL-5RL | 6.5V |
| Round Liner (RL) | 7RL-9RL | 7.0V |
| Round Liner (RL) | 11RL-18RL | 7.5V |
| Round Shader (RS) | 3RS-11RS | 7.0V - 7.6V |
| Round Shader (RS) | 88RS-111RS | 10V |
| Round Magnum (RM) | 5RM-9RM | 6.8V |
| Round Magnum (RM) | 11RM-15RM | 7.1V |
| Round Magnum (RM) | 17RM-25RM | 7.5V |
| Round Magnum (RM) | 25RM-29RM | 8.0V |
| Magnum (M) | 5M-9M | 6.6V |
| Magnum (M) | 11M-15M | 7.0V |
| Magnum (M) | 17M-25M | 7.4V |
Maintenance
1. Cleaning the Machine
- Always power off and disconnect the pen before cleaning.
- Wipe the exterior of the machine with a soft, damp cloth and a mild disinfectant.
- Do not immerse the pen in liquid or allow liquids to enter the internal components.
- Ensure the machine is completely dry before storage or next use.
2. Cartridge Disposal
Used tattoo cartridges are biohazardous waste. Dispose of them safely and according to local regulations for sharps disposal.
3. Battery Care
- Avoid fully discharging the battery frequently.
- Store the device in a cool, dry place when not in use.
- If storing for extended periods, charge the battery to about 50% to prolong its lifespan.
Troubleshooting
- Machine Not Turning On: Ensure the battery is charged. Connect to the charger and try again.
- Needle Not Moving: Check if the cartridge is properly inserted and secured. Verify the machine is powered on and not paused.
- Inconsistent Performance: Ensure the cartridge needle is not damaged. Check battery level.
- Overheating: If the machine feels excessively hot, pause operation and allow it to cool down. Prolonged high-voltage use can cause heat.
If problems persist, refer to the official user manual PDF or contact customer support.
Specifications
Figure 4: Diagram showing key parameters of the Dragonhawk A1 Tattoo Pen.
| Feature | Specification |
|---|---|
| Model Number | Dragonhawk Complete Tattoo Kit (A1) |
| Machine Type | Wireless Tattoo Machine |
| Motor Type | Dragonhawk Customized Motor |
| Stroke Length | 3.5mm |
| Working Voltage | 5-12V |
| Speed | 12V/12000RPM |
| Battery Capacity | 1600mAh |
| Charging Time | 2-3 hours |
| Working Time | 6-7 hours |
| Machine Weight | 167g |
| Diameter | 32mm |
| Length | 120mm |
| Charging Method | Type-C |
| Dot Mode Levels | 1-9 levels |
| Voltage | Below-50V AC (SELV AC) |
| Batteries Included | Yes |
For a complete list of specifications and detailed diagrams, please refer to the official user manual PDF: Dragonhawk A1 User Manual (PDF)
User Tips
- Ink Usage: The included ink package is generally suitable for practice on artificial skin or for testing purposes. For professional use on clients, always use high-quality, sterile inks from reputable brands.
- Product Quality: Users frequently praise the quality of the Dragonhawk A1 pen. Proper maintenance will help preserve its performance.
- Needle Selection: Experiment with different needle types and sizes to find what works best for various tattoo styles and effects. Refer to the recommended voltage table for guidance.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact the Dragonhawk Official Store directly through your purchase platform or visit their official website. Keep your proof of purchase for any warranty claims.