Introduction
Thank you for choosing the AFU AF300 Smart Charger. This manual provides essential information for the safe and efficient operation of your charger. Please read it carefully before using the product.
The AFU AF300 is a 79.8V 3A charger designed for 19S 70.3V Lithium Battery Packs, LiFePO4, and Lead Acid batteries. It features a cooling fan, fast charge capability, auto-stop function, and an aluminum case with an OLED display.
Important Safety Instructions
⚠️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- Before using your battery charger, read all safety instructions.
- Before use, ensure that the local power grid voltage is consistent with the AC configuration of the charger to avoid charging the battery with an incorrect input voltage.
- Avoid charging the wrong type of battery.
- Always check connector/cable polarity before connecting to the battery.
- Always use the charger in well-ventilated, dry environments.
- Do not cut the power cord.
- Do not submerge in water or get wet.
- Due to the high current, sparking is normal when connecting the charger to the battery.
- Do not cover the aluminum case; this can cause your charger to overheat while charging.
- Do not disassemble the charger.
- The battery may be damaged if the LED2 indicator light does not turn green after being charged for an extended amount of time.
- Risk of electrical shock. Do not touch uninsulated portions of AC or DC connectors or uninsulated battery terminals.
- To prevent electrical shock, make sure all electrical connectors are in good working condition. Do not use connectors that are cracked, corroded, or do not make adequate electrical contact. Use of a damaged or defective connector may result in a risk of overheating or electrical shock.
- Never alter the AC cord or plug provided. If it will not fit the outlet installed by a qualified electrician, improper connection can result in a risk of electric shock.
- Do not attempt to repair or service the charger yourself. Opening the charger may expose you to high voltages, the risk of electric shock, and other hazards.
- Do not splice the AC power cord.
- Damaged cords and plugs can cause electric shock or electrocution.
- When using an extension cord, make the AC connection to the charger outside of the battery compartment as far away as practical to reduce the risk of a spark igniting gases in the compartment.
- Even though the charger is capable of operating in a high ambient temperature environment, a minimum of six inches of unobstructed area should be allowed on all sides of the unit for proper air circulation and cooling. Proper cooling and circulation will allow the charger to operate at peak efficiency.
Package Contents
The package includes:
- 1 x Battery Charger
- 1 x Input Wire (Power Cord)
- 1 x User Manual
- Fuses (as shown in video)
The charger features an integrated MCU and PWM for power control.
Video: Unboxing and overview of the AFU AF300 Smart Charger, including the charger unit, power cord, owner's manual, and spare fuses.
Product Overview

Image: Front view of the AFU AF300 Smart Charger, highlighting the OLED display and charging indicators.

Image: Detailed view of the OLED display, indicating Voltage (V), Temperature (℃), Electric Current (A), and Power (W).

Image: Product Structure - Exploded view showing the Charger Shell, Power Output, Power Input, and Power Indicator.
Setup and Operation
Quick Start Instructions
- Connect the detachable input power cord: Ensure a tight connection to the charging unit.
- Plug the output plug into the battery charging socket: Connect the output plug into the battery charging socket on the battery. LED1 will turn red and LED2 will turn green initially.
- Connect the battery charger to an electrical outlet: Do not face the battery when making this connection.
- Charging Indication: When the output plug is successfully connected, LED2 will light up in red.
- Monitor Charging: Keep your battery charging until the LED2 light turns green, indicating that it is fully charged.
- Automatic Maintenance Mode: If the charger remains plugged in, automatic maintenance mode will be turned on, and the charger will continuously monitor the battery to charge it during storage.
- Disconnect: Disconnect the output plug from your battery, then disconnect the power supply cord from the electrical outlet.
- Storage: Store your Battery Charger in a dry environment.

Image: Working Ambient Temperature - Maximum 40℃, Minimum -20℃.
LED Indicators
| Status | LED1 | LED2 |
|---|---|---|
| AC Power Connected | Red | Green |
| Charging | Red | Red |
| Fully Charged/Standby | Red | Green |
3-Stage Smart Charging Mode
The charger is designed to automatically protect and preserve your batteries through a three-stage intelligent charging process:
- Stage 1: CC (Constant Current)
- Stage 2: CV (Constant Voltage)
- Stage 3: Float Charging or Trickle Charging
This ensures the battery is fully charged and maintained. For Lead Acid chargers, float charging is applicable.

Image: Charging Curve - Two different charging modes are shown in schematic diagram for Lead-acid and Lithium-ion/LiFePO4 batteries, illustrating CC, CV, and Trickle/Float charge stages.
Troubleshooting
1. Plug in AC power cord charger without any indication:
- Check if the input AC has 110V or 220V. (Note: Be sure to use the input voltage required by the charger).
- Check if the input AC line or fuse is damaged.
2. LED1 is red and LED2 is green but nothing happens when you insert the output plug into your battery:
- Check if the output plug is fully inserted into the battery.
- Check if there are any loose or corroded connections on your battery terminals.
- Check if the output fuse is damaged.
3. The battery meter on your battery reads full but the charger is still running:
Many aftermarket battery meters are calibrated to read the measured voltage until the charger has been taken off for 12-24 hours. Let the charger continue to run until the charge cycle has been fully completed.
4. The batteries sound like they are “boiling” (This applies only to lead-acid batteries):
The batteries are not boiling. The sound you hear is the release of hydrogen gas bubbles during the bulk recharge phase. The release of hydrogen gas bubbles stirs up the sediment in the bottom of the batteries and helps to maintain a healthy environment. If fluid is bubbling out of the battery during charging, immediately disconnect the charger. This can be a sign that too much fluid has been added to the batteries.
5. How loud should the charger be?
The noticeable sound of rushing air from the fan is a normal part of the cooling process on your rapid charger.
6. How warm do chargers get?
The battery chargers can reach 140°F (60°C). They may get warm in an enclosed area. The maximum recommended air temperature for charging batteries is 105°F (40.5°C). When the charger is hot, the output current will drop to protect the charger and the battery.
7. Will I damage my batteries if I leave the charger plugged in over long periods of non-use (like storage)?
No. You only need to place the charger in a well-ventilated and dry environment, and the charger will not be damaged.
8. Why do the LEDs on my charger stay illuminated for a period of time after unplugged from AC power?
This is normal and does not affect your batteries. It is simply a function of the precision charging, ensuring the charger is disconnected prior to terminating the charge cycle.
Specifications
| Attribute | Value |
|---|---|
| Product Name | AF300 Battery Charger |
| Brand Name | AFU |
| Model Number | AF300-79803B |
| AC Input Voltage | 100~120V/200~240Vac |
| Frequency | 50~60Hz |
| DC Output Voltage | 79.8 Volt |
| DC Output Current | 3 Amp |
| Dimension | 135*90*50mm (5.3*3.54*1.97in) |
| Net Weight | 1KG (2.2lbs) |
| Case Color | Black |
| Case Material | Aluminum case |
| Suitable Battery Type | 19S 70.3V Li-ion Lipo Battery (S=Series Connection) |
| Efficiency | ≥85% |
| Charging Mode | Three-stage Intelligent Charging Mode: Constant Current~Constant Voltage~Trickle(Floating Charge) to Ensure Battery Fully Charged (Floating Charge is when Lead Acid charger) |
| Charging Indicator | Red and Green, double color instructions, Red logo charging, Green logo finished or standby |
| Operating Ambient Temperature | -20~+40℃ (-4~104℉) |
| Operating Relative Humidity | 95% |
| Operating Atmospheric Pressure | 70~106kpa |
| Storage Ambient Temperature | -40~+70℃ (-40~158℉) |
| Storage Relative Humidity | 95% |
| Storage Atmospheric Pressure | 60~95kpa |
| Various Protection | Over Current, Over Voltage, Over temperature, Short Circuit, Reverse Polarity, shut off or trickle and anti-reverse charge |
| Safety Certifications | CE, RoHS, FCC Directive-compliant |
| Features | Intelligent IC control, full automatic transition of CC, CV and Float/Cut-off trickle, Aluminum case, Robust, Elegant, Safe, Stable, Reliable |
| Output Power | 150-500W (including 500W) |
| Voltage Range | High voltage (50-1000V DC, 75-1000V AC) |
| Power Source | AC&DC |
| Display Screen | Yes |
| Intelligent Charge | Yes |
| Quick Charge | No |
| Type | Electric |
| Origin | Mainland China |

Image: Dimensions (5.3*3.54*1.97 inches) and Weight (2.2 lbs) of the charger.

Image: Multiple Protection features including Super heat dissipation, Temperature protection, Overvoltage protection, Anti-protection, Overcurrent protection, Voltage protection, Short circuit protection, and Balance function.

Image: Input plug types (A to L). Choose according to your demand.

Image: Output plug types (1 to 12), including Wire Nose - M8, Alligator clip, Anderson 45A, Anderson 50A, GX16-3pin 1+3-, GX16-3pin 1+2-, DC 5.5*2.1mm, C13 N+L-, RCA, XLR-3pin 1+2-, XT60 male, XT90 male. Choose according to your demand.
Application Scenarios

Image: Application Scenarios - The charger is suitable for E-Bikes, E-Motorcycles, E-Tricycles, E-Sightseeing Vehicles, Low Speed E-Vehicles, E-Yachts, E-Forklifts, Solar Energy Storage, and Energy Storage Systems.
Warranty and Support
Warranty Information
The manufacturer's warranty is 12 months.
Warranty is not provided in the following cases:
- Damage caused by installation and use in violation of product instructions.
- Damage caused by unauthorized modification or repair.
- Exceeding the use environment, natural disasters, or other force majeure causes damage.
Support
If you have any questions, concerns, or missing parts, please contact the online retailer you purchased from.
For further assistance, you may refer to the official seller's contact information:

Image: Contact Us - 24-hour service from AFU Official Store, including a QR code and WhatsApp/WeChat number: 13688869226.
A PDF user manual is also available for download: View User Manual (PDF)
User Tips
- Always ensure proper ventilation around the charger during operation to prevent overheating and ensure peak efficiency.
- Double-check the compatibility of the charger's output plug and voltage with your battery before connecting.
- The OLED display provides real-time information on voltage, current, temperature, and power, which can be useful for monitoring the charging process.