DykbRadio IP2366 2S 3S 4S 5S 6S Lithium Battery Charging Board

Contents

IP2366 PD3.1 140W Bidirectional Fast Charging Module User Manual

Model: IP2366 2S 3S 4S 5S 6S Lithium Battery Charging Board | Brand: DykbRadio

1. Product Overview

The IP2366 PD3.1 140W Bidirectional Fast Charging Module is a versatile solution for charging and discharging 2S, 3S, 4S, 5S, and 6S Lithium-ion and LiFePO4 battery packs. It supports various fast charging protocols, including PD3.1, FCP, AFC, SCP, and QC2.0/QC3.0/QC3.0+, offering up to 140W bidirectional power delivery. This module is designed for DIY electrical projects requiring efficient battery management.

Key Features:

  • Supports 2S, 3S, 4S, 5S, 6S Lithium-ion and LiFePO4 battery packs.
  • PD3.1 140W bidirectional fast charging (input/output).
  • Integrated FCP, AFC, SCP, QC2.0/QC3.0/QC3.0+ protocols.
  • Adjustable battery string and type selection via switches.
  • Automatic temperature control with external fan interface.
  • Power indicator lights for charge status.

2. Safety Warnings and Precautions

2.1. Safety Warning

▲WARNING: Stay away from children and avoid misoperation.

▲WARNING: Please do not disassemble or modify this product by yourself. Non-professional repairs may cause damage or safety accidents.

2.2. Precautions

  • Do not use in damp or dusty environments.
  • Avoid severe impact or vibration on the product.
  • Ensure correct battery string and type selection before connecting and recharging to prevent damage.
  • When using an external fan, pay attention to positive and negative polarity.
  • Reduce power consumption or ensure good heat dissipation if the battery pack internal resistance is high or capacity is large (>8000mAh).

3. Setup Instructions

Before connecting the module, ensure all accessories are present and review the following steps carefully.

3.1. Component Identification

Labeled diagram of the IP2366 module showing components like power indicator, maximum power selection pad, external fan terminal, battery string selection switch, and battery type selector switch.
Figure 1: IP2366 Module Component Layout
  1. Maximum Power Selection Pad: Solder short connections to select maximum power (65W, 100W, 140W). Higher power generates more heat.
  2. Battery String Selection Switch: Dial down to open. Select the number of strings (2S, 3S, 4S, 5S, 6S) corresponding to your connected battery pack. Note: Pulling down both 3S and 4S together selects 2S.
  3. Battery Type Selector Switch: Dial down to open. Select the switch corresponding to your battery's charging cutoff voltage (e.g., 4.4V, 4.35V, 4.2V, 4.1V). For 3.65V, pull down both 4.2V and 4.1V.
  4. External Fan Interface Terminal: Connect an external fan here. The fan will automatically turn on when the board temperature exceeds 65°C and turn off below 65°C. Ensure correct polarity. The fan voltage should match your battery pack voltage.
Close-up of the battery string and battery type selector switches on the IP2366 module, with voltage and string count labels.
Figure 2: Battery String and Type Selector Switches

3.2. Initial Connection Steps

  1. Set Switches: Before connecting the battery, correctly set the Battery String Selection Switch and Battery Type Selector Switch according to your battery pack's configuration.
  2. Connect Battery: Connect your 2S-6S battery pack to the module. Ensure correct polarity and that the battery wires are capable of handling over 15A current.
  3. Activate Module: Plug a standard and legitimate USB-C charger into the TYPE-C port to activate the module.

Note: Always choose the appropriate option on the switches before connecting the battery and recharging. Incorrect selection can prevent normal charging/discharging.

4. Operating Instructions

4.1. Charging

Once the module is set up and activated, it will begin charging the connected battery pack. The power indicator lights will show the charging status.

IP2366 module connected to a battery pack and a USB power meter, showing charging in progress.
Figure 3: Module Charging a Battery Pack

4.2. Discharging (Power Bank Function)

To use the module for discharging (e.g., charging a phone):

  1. Connect your device (e.g., phone) to the module's USB-C port.
  2. Briefly press the button on the module to initiate discharge.

4.3. Battery Level Indication

For accurate battery level indication, ensure the consistency of battery voltage, capacity, and internal resistance (ideally <15mΩ). The battery level will automatically calibrate after more than one full charge and discharge cycle.

Video 1: Demonstration of the IP2366 module in operation, showing connections and charging.

5. Maintenance

  • Heat Dissipation: If using the module at high power (especially 140W) or with large capacity battery packs, ensure adequate heat dissipation. The external fan interface can be utilized for this purpose.
  • Environmental Conditions: Keep the module in a dry, clean environment, free from dust and moisture.
  • Inspection: Periodically inspect connections and components for any signs of wear or damage.

6. Troubleshooting

6.1. Indicator Light Keeps Flashing

A continuously flashing indicator light signals an error. This could be due to:

  • Incorrect switch settings for battery string count or voltage type, leading to overvoltage or undervoltage detection.
  • The connected charger's output voltage being too high or too low, or having excessive ripple, preventing proper operation.

6.2. Not Triggering 140W Fast Charging

  • Protocol Detector Settings: If using a protocol detector, ensure it is manually set to detect 140W. Refer to your detector's manual.
  • Data Cable: Use a regular, standard 140W compatible USB-C data cable. Some cables may not support this power level.
  • Charger Compatibility: The charging device or charger must support PD3.1 140W to trigger this fast charge mode.

6.3. Battery Display Issues (e.g., full charge then immediately no power)

This can be caused by:

  • Battery wires being too thin.
  • High internal resistance of the battery.
  • A faulty section within the battery pack.

6.4. How to Detect if the Circuit Board is Good

You can test the board with a PD3.0 fast charger and a multimeter:

  1. Confirm your charger can output PD fast charge 20V and your multimeter is functional.
  2. Set the circuit board to 4S/4.2V. Plug in the charger. After 10 seconds, measure the voltage at the battery pad terminal with a multimeter. It should be approximately 16.8V (normal voltage reduction).
  3. Remove the charger. Switch the board to 6S/4.2V. Measure the voltage at the battery pad terminal. It should be approximately 25.2V (normal voltage boost).

Note: Some mobile phone charger protocols may not match well, causing unstable voltage readings. Measure within 30 seconds of plugging in the charger, as some chargers automatically turn off output when there's no load.

6.5. Common Errors to Avoid

  • Incorrect Wiring: Always double-check wiring polarity before powering on. Incorrect connections can damage the module.
  • Switching After Battery Connection: Do NOT change the selector switches after the battery is connected. The module detects switch states only upon power-on. If you need to change settings, first disconnect the battery, wait for capacitors to discharge (approx. 1 minute), then set the switches, reconnect the battery, and plug in the charger to reactivate.

7. Specifications

FeatureSpecification
Model NumberIP2366 2S 3S 4S 5S 6S Lithium Battery Charging Board
TypePD3.1 140W bidirectional fast charging module
Supported Battery TypesLi-ion, LiFePO4, Polymer batteries (2S, 3S, 4S, 5S, 6S)
Max Power Output/Input140W (Max 28V5A)
Supported Voltages5V, 9V, 12V, 15V, 20V, 28V
Fast Charging ProtocolsIntegrated FCP, AFC, SCP, DRP Try SRC, PD3.1, QC2.0/QC3.0/QC3.0+
Size60mm x 60mm
DIY Supplies CategoryElectrical
Package Dimensions (L x W x H)16cm x 18cm x 4cm
Package Weight0.045 kg

8. User Tips

  • Charger Quality: Always use a standard and legitimate fast charger. Some high-end phone chargers with proprietary protocols may not be compatible.
  • Cable Quality: Invest in a high-quality, standard 140W compatible USB-C data cable to ensure full power delivery.
  • Battery Pack Health: For optimal performance and accurate battery level readings, ensure your battery pack has good cell consistency, especially low internal resistance (<15mΩ).
  • Heat Management: If you plan to use the module for extended periods at high power, consider adding an external fan for cooling to maintain efficiency and longevity.
  • Initial Setup is Key: The most common issues arise from incorrect switch settings or changing them after the battery is connected. Always set switches first, then connect the battery.

9. Warranty and Support

For any issues, questions, or support needs regarding your IP2366 PD3.1 140W Bidirectional Fast Charging Module, please contact our store support directly. We are committed to assisting you with product functionality and troubleshooting.

An official user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.