BAOFENG UV-32

Contents

BAOFENG UV-32 GPS Walkie Talkie User Manual

Model: UV-32

1. Introduction

Thank you for purchasing the BAOFENG UV-32 Series Amateur Radio. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications with peak efficiency. Please read this manual carefully before use to ensure you derive maximum performance from your radio.

This manual is applicable to the UV-32 and AR-32 Series Amateur Radios.

1.1 Important Safety Information

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

The operation of your Baofeng radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government's department of Innovation, Science, and Economic Development Canada (ISED). ISED requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.

CAUTION: This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide that comes with the radio. This guide contains operating instructions for safe usage, RF energy awareness, and control for compliance with applicable standards and regulations.

Any modification to this device, not expressly authorized by Baofeng, may void the user's authority to operate this device.

Under Innovation, Science, and Economic Development Canada (ISED) regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved by the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Innovation, Science, and Economic Development Canada (ISED) to operate with Baofeng-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Operating Prohibitions

  • Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
  • Do not operate the product near or in any blasting area.
  • Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips for Use

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Please operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
  • Handle the product with care.
  • Do not disassemble, modify or repair the product and its accessories without authorization.

2. Key Features

The BAOFENG UV-32 GPS Walkie Talkie offers a range of advanced features for enhanced communication and usability:

  • 2.0" TFT large screen, full keyboard, fully open menu operation
  • GPS positioning function, location sharing and requesting location information from others
  • Bluetooth APP application for reading or writing radio data
  • 10 zones storage, up to 1000 named memory channels
  • High/Middle/Low power selectable (10W Tri-power)
  • Scanner function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, scan channel addition and removal
  • Built-in input method, allows this device to edit channel name
  • NOAA Weather Radio Channel Reception (in the United States and Canada)
  • Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
  • Type-C direct charging and charging stand, more convenient battery life
  • Dual-band handheld transceiver
  • High Capacity Lithium-Ion battery
  • Alarm function
  • Function beep on the keyboard
  • One touch search frequency
  • VOX (voice activated transmit)
  • Broadcast FM radio receiver 78-108 MHz
  • Display illumination programmable via keypad
  • Dual watch / Dual reception
  • Two (2) pins for Kenwood accessory port
  • Scanning receiver frequency range: FM 76-108 MHz; AM 108-136MHz, VHF 136-174MHz, 220-260MHz, UHF350-390MHz, 400-520MHz
BAOFENG UV-32 with key features: Bluetooth Programming, GPS Positioning, Wireless Copy Frequency, AM/FM, 1000 Channels, 2 Charger Methods, and various frequency ranges.

Figure 1: BAOFENG UV-32 Key Features Overview

BAOFENG UV-32 with Bluetooth APP Programming, GPS, Multi Band, Wireless Copy Freq, Tri Power, 2.0 inch TFT Large Screen, 1000 Channels, Type-C Charger, VOX, NOAA.

Figure 2: BAOFENG UV-32 Advanced Features

Usage scenarios for BAOFENG UV-32: Driving, Hunting, Property Management, Logistics.

Figure 3: Typical Usage Scenarios

3. Setup and Initial Use

3.1 Package Contents

Your transceiver package should include the following items:

  • 1x Portable radio
  • 1x Antenna
  • 1x Li-ion battery pack
  • 1x Desktop charger
  • 1x Type-C cable
  • 1x User's manual
Contents of the BAOFENG UV-32 package: UV-32 radio, GPS, Bluetooth APP Programming, 1000CH, Wireless Copy Frequency, Dual Speaker, USB-C cable, Antenna, Battery, Bag, Clip, Instructions.

Figure 4: Package Contents

3.2 Battery Information and Charging

The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge and discharge the battery two or three times.

Charging the Battery Pack

  • Use only the specified charger provided by Baofeng.
  • Install the battery pack onto the radio.
  • Turn off the radio before charging.
  • Plug the Type-C cable into the Type-C charging port on your battery. Connect the other end of the Type-C charger to a wall power outlet.
  • An empty battery will be fully charged in approximately 6 hours.
  • The battery indicator light illuminates to indicate that the battery is charging.
Two charging methods for BAOFENG UV-32: Type-C Fast Charging and Base Charging.

Figure 5: Charging Methods

Multiple charging methods for BAOFENG UV-32: Base charger, power bank, and laptop charging via Type-C.

Figure 6: Versatile Charging Options

Battery Maintenance Precautions

  • Do not short the battery terminals or throw the battery into a fire.
  • Never attempt to remove the casing from the battery pack.
  • Charge the battery between 5°C-40°C (40°F - 105°F).
  • Do not cut off power or remove the battery during charging until the green light is on.
  • Do not recharge a fully charged battery.
  • Do not charge a damp battery.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.
  • Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

3.3 Installing / Removing the Battery

Installing the Battery Pack

  1. Position the battery pack over the back of the radio.
  2. Engage the battery pack into the radio until it is fully seated.
  3. Tighten the screws using a coin or object to secure the battery pack. Do not overtighten.

Removing the Battery Pack

  1. Loosen the screws on the back of the battery pack.
  2. Lift the bottom of the battery pack slightly to remove it from the radio housing.
  3. Pull the battery pack out of the radio housing.

3.4 Installing / Removing the Antenna

Installing the Antenna

  1. Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.

Removing the Antenna

  1. Turn the antenna counter-clockwise to remove it.
Comparison of signal range with original antenna (20.5CM/8.07inch) and longer antenna (39CM/15.35inch) for 10Watt output.

Figure 7: Antenna Length and Signal Range

3.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

4. Operation

4.1 Radio Overview and Controls

Detailed view of BAOFENG UV-32 radio with labels for Antenna, Encoder/channel selector switch, TX RX status indication, Power/Volume knob, PTT key, Side Key (SK1), Side Key (SK2), 2 inch color LCD screen, Accessory port, Numeric keypad, Built-in Microphone, Charge contact, Speaker, Type-C Charging port.

Figure 8: BAOFENG UV-32 Components

Components:

  1. Antenna
  2. Encoder/channel selector switch
  3. TX_RX status indication
  4. Power/Volume knob
  5. 2" color LCD screen
  6. PTT key
  7. Side key (SK1) - short press to customize function, long press to emergency alarm
  8. Side Key (SK2)-Sweep/Monitor
  9. Numeric keypad
  10. Built-in Microphone
  11. Charge contact
  12. Speaker
  13. Accessory port
  14. Type-C charging port

SK1 allows you to set shortcut functions through the CPS programming software or the radio's menu.

4.2 LCD Icon Summary

IconDescription
[Battery Icon]Battery level indicator
[Speaker Icon]Make sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI.
DDual watch enabled
VVOX enabled
*Bluetooth frequency writing function activated
[GNSS Icon]GNSS function enabled
[Keypad Lock Icon]Keypad lock enabled
ZONE01Indication of the current channel's region. Working in storage mode
VFOIn the current working VFO mode. Allow manual frequency input
AA displays (upper section) and emission level indication
BB displays (lower section) and emission level indication
HTransmit power level indicator, According to Power High
MThe current transmission power is medium power (used in normal environments).
LTransmit power level indicator, According to Power Low
DDCS enabled
CCTCSS enabled
[Up Arrow]Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX.
RReverse function enabled
TTalkaround has been activated, off grid at the central turntable. The transmission frequency is equal to the receive frequency
[Lock Icon]The confidential calling feature is activated
NNarrowband enabled

4.3 Basic Operations

Power On/Off

  • Turning On: Rotate the Volume/Power knob clockwise until you hear a "click". A double beep and display message/flash will indicate it's on. If Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
  • Turning Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

Adjusting the Volume

  • Turn the Volume/Power knob clockwise to increase volume.
  • Turn the Volume/Power knob counter-clockwise to decrease volume.
  • Use the monitor function (enabled by [VOX/Monitor] key below PTT) to adjust volume with un-squelched static.

Main Band/Sub Band Switch

  • In standby mode, press the [Up Arrow] key to switch between the main frequency band or sub frequency bands. The band with the larger display font is primary.

VFO/Channel Switch

  • Press and hold the [Menu] key to switch between VFO and channel display.
  • In channel mode (MR), the channel number will be displayed.
  • In frequency mode (VFO), the VFO icon will be displayed.

Frequency (VFO) Mode

  • Use the [Up Arrow] or [Down Arrow] keys to navigate up and down the band. Each press increments/decrements frequency by the set step.
  • Directly input frequencies using the numeric keypad (e.g., 436.61250 MHz: [4][3][6][6][1][2][5][0]).

WARNING: Transmitting on unauthorized frequencies is illegal. Listening is generally legal. Consult local regulations.

Channel (MR) Mode and Channel Selection

  • Press and hold the [Menu] key to switch between VFO and Channel mode.
  • Use the [Up Arrow] or [Down Arrow] navigation keys to select the channel.
  • Alternatively, input channel numbers directly (e.g., for channel 12, input [0][1][2]).

Select a Bank

The radio supports up to 10 banks, with a maximum of 100 channels per bank.

  • Press [Menu] key, go to Menu > Bank, press [Up Arrow] or [Down Arrow] to select a bank, and then press [Menu] key to switch.

Making a Call

  • Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with normal tone. The red LED will be on.
  • Frequency mode call: Press and hold [Menu] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on.
  • Receive a call: Release the [PTT] key. The green LED will be on when receiving a call.
  • Keep the microphone 2.5 cm to 5 cm from your mouth for best reception.

Emergency Alert

  • To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash.
  • To exit, press the [SK1] key.

WARNING: Use Emergency Alert only in actual emergencies.

FM Radio (FM)

  • Frequency range: 65-108MHz.
  • Press [Menu] key to switch between 65-75 MHz and 76-108 MHz bands.
  • In frequency or channel mode, Press [SK1] key to turn on the radio.
  • To exit, press [SK1] key.

Monitor

  • In standby, press and hold the [SK2] key to enter Monitor mode. This allows monitoring weak signals.
  • Release [SK2] key to turn off speakers and return to standby.

Keypad Lock

  • To enable/disable, press and hold the [*] key for about two seconds.
  • Can also be set to automatically lock after ten seconds from the menu.

Frequency Reversal and Talkaround

  • A short momentary press of the [R] key enables the reverse function.
  • Press the [R] key again to switch to talkaround mode.

TX Repeaters Tone

  • Press [PTT] + [SK1] key to send 1750Hz repeaters tone.
Steps for One Touch Search Frequency: 1. Turn on, long press the keyboard. 2. When 'SEARCH' appears, press to switch Band. 3. Screen appearance frequency, press to save channel.

Figure 9: One Touch Frequency Search

  1. Define [SK1] side key as a Search function via CPS software or radio menu.
  2. Briefly press the preset 'Search' key; screen displays "SEARCH SEEK...".
  3. If a transmitter continues to transmit and the unit receives an effective frequency, it will be displayed. If CTCSS or DCS is present, its value will be displayed.
  4. Press the [Menu] key to save the Search frequency and CTCSS or DCS to the channel.

Scanner

  • To enable, press and hold the [#] key for about two seconds.
  • Change scanning direction with [Up Arrow] or [Down Arrow] keys.
  • To exit, press and hold the [#] key.

GPS Function

Two BAOFENG UV-32 radios displaying GPS positioning information on their screens, indicating real-time location sharing.

Figure 10: Global Positioning System (GPS)

The UV-32 features a multi-mode GPS module (GPS from the United States and Beidou from China).

GPS On/Off Settings
  • Go to Menu > GNSS > GPS On/Off. Use [Up Arrow]/[Down Arrow] to select ON/OFF.
Time Zone Settings
  • Go to Menu > GNSS > Time Zone. Use [Up Arrow]/[Down Arrow] to select the correct time zone.
GPS Mode Settings
  • Go to Menu > GNSS > GPS Mode. Use [Up Arrow]/[Down Arrow] to select GPS mode (BDS, GPS, or GPS+BDS).
Using GPS
  • In standby mode, press [P1] key to enter GPS mode and display "My Place".
  • Press [P2] to enter GPS mode and display the coordinate interface.
  • Press [Menu] key to switch My Place in information list mode or electronic compass mode.
  • Press [Up Arrow]/[Down Arrow] key to switch information of the selected member.
Find My Place
  1. Press [P1] key to enter GPS mode.
  2. Use the [Up Arrow]/[Down Arrow] key to switch to "My Place".
  3. The GPS will display "Searching..." (red GPS character).
  4. Once successful, it will display "Searching Successful" (green GPS character) and show time, longitude, latitude, and altitude.
  5. Press the [Menu] key to switch between GPS position information and GPS distance/direction.

Note: If "Searching..." is displayed for a long time, search for satellites in an open location.

Share My Place Information (Send to Others)
  1. After successful GPS positioning, press the [Menu] key to switch to the location information interface.
  2. Use [Up Arrow]/[Down Arrow] key to select the pre-programmed member sequence (01-20), labeled as "native".
  3. Press the [PTT] key to share current location information.
Requesting Someone Else's Place
  1. After successful GPS positioning, press the [Menu] key to switch to the My Place information interface.
  2. Use [Up Arrow]/[Down Arrow] key to select the pre-programmed member sequence (01-20) not marked as "native".
  3. Press the [PTT] key to initiate a position request command to the target member.

NOAA Weather Reception

BAOFENG UV-32 radio with 10 NOAA Weather Reception feature, showing All Hazards NOAA Weather Radio logo.

Figure 11: NOAA Weather Reception

The NOAA feature automatically scans and receives weather reports, providing timely information about incoming bad weather. This can be a crucial alternative communication option during disasters when cell towers are overloaded.

Bluetooth Wireless Programming

Video 1: Phone APP Wireless Programming, GPS function, One Click Frequency Matching

Phone APP Wireless Programming, Easy to Operate, showing iOS and Android compatibility.

Figure 12: Phone APP Wireless Programming Interface

The UV-32 supports Bluetooth wireless programming via a dedicated smartphone application (iOS and Android compatible).

Download BAOFENG Radios APP

Scan the QR code below to download and install the BAOFENG Radios APP:

QR codes for downloading the Bluetooth Programming APP for iOS and Android.

Figure 13: Bluetooth Programming APP QR Codes

Programming Steps
  1. Open the APP, enable Bluetooth on your phone, and open the positioning function.
  2. Select the brand "Baofeng" in the APP, then select the model "UV32 Pro Series".
  3. Connect the radio via Bluetooth. Once connected, the APP will prompt "connection success".
  4. From the homepage, you can read and write frequencies.
Read Frequency

After reading the frequency, click "program" to enter program details. In the program details interface, you can program channel information, frequency mode, and optional functions.

Save Profile

The programmed scheme allows you to save it as a new profile. If you choose to replace an existing program, tap to replace and save it.

Write Frequency

Tap Home, select Program, then tap Write Frequency. The radio will restart automatically after finishing.

Main Menu Functions

The menu allows operations like selecting BANKS, SCAN, Bluetooth, GNSS, Radio Settings, Program Channels, Recording, and Radio Information.

Basic Use with Arrow Keys
  1. Press the [Menu] key to enter the main menu.
  2. Use [Up Arrow] or [Down Arrow] keys to navigate between menu items.
  3. After finding the desired menu item, press the [Menu] key again to select it.
  4. Use [Up Arrow] or [Down Arrow] keys to navigate between next menu items.
  5. After finding the desired next menu item, press the [Menu] key again to select it.
  6. Use [Up Arrow] or [Down Arrow] keys to select the desired parameter.
  7. To confirm your selection, press [Menu] key (saves setting and returns to main menu).
  8. To cancel changes, press [Home] key (resets item and exits menu).
  9. To exit menu at any time, press the PTT key.
Using Short-cuts

Each menu item has a numerical value for direct access.

  1. Press the [Menu] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [Menu] key.
  4. For entering the desired parameter, use arrow keys or numerical short-cut code.
  5. To confirm, press [Menu] key. To cancel, press [Home] key.
  6. To exit menu at any time, press the PTT key.
Shortcut Menu Operations Table
MenuNameSettingDescription
BANKBANK 1Channel1-Channel100A Bank is a group of channels. 10 Banks, max 100 channels per bank.
Freq RangerNNNNnnnInput VFO range lower and upper frequency
SCANScan ModeTimeScanning resumes after fixed time.
CarrierScanning resumes after signal disappears.
SearchScanning will not resume.
Scan SubCodeCTCSSSearch within CTCSS Tone (67-254.1, 50 groups).
DCSSearch within DCS Code (023N-7541, 210 groups).
Scan MemoryALLRX_TX are saved (default is all, encoding and decoding are the same).
DECODERSave only in Transmitter CTCSS/DCS.
ENCODERSave only in Receiver CTCSS/DCS.
BluetoothBluetoothOFFTurn off Bluetooth frequency write function.
ONEnable Bluetooth frequency write function.
Radio SettingStep2.5-100KSelects frequency change in VFO/Frequency mode when scanning or pressing keys.
SquelchOFF, LEVEL1-LEVEL5Squelch silences receiver when no signal. Setting to 0 opens squelch entirely.
Power SaveOFFTurn off radio sleep. Battery consumption is large, standby time shortened.
ONTurn on radio sleep. More power efficient, but might miss first few syllables.
VOX SwitchOFFTurn off radio VOX.
ONTurn on radio VOX.
VOX LevelLEVEL1-LEVEL9Adjust gain level for smooth transmission.
VOX Delay0.5...2.0sSet VOX delay to extend transmission time.
TOT15;30;45...180Maximum allowed time for transmission.
TOA1...10Activate TOA function. Range 0 - 10 seconds, Step 1 second.
VoiceOFFDisable voice prompts.
ONActivate voice prompts.
LanguageChineseDisplay menus and voice prompts in Chinese.
EnglishDisplay menus and voice prompts in English.
ROGEROFFDisable ROGER function.
ONActivate ROGER function. Sends end-of-transmission tone.
BeepOFFDisable key confirmation tone.
ONActivation key to confirm tone.
BackLightALWAYS ONBacklight is always on.
5...20Set backlight off time in no-operation delay time.
Power on DisplayPICTUREShow preset picture when radio is on.
VOLTAGEDisplay battery voltage when radio is on.
Dual WatchOFFDisable dual table, dual receive.
ONMonitor [A] and [B] at the same time. Display with most recent activity.
AutoLockOFFDisable automatic keypad lock.
ONKeypad locked if not used in 8 seconds.
Alarm ModeOn SiteSounds alarm through radio speaker only.
Send SoundTransmits a cycling tone over-the-air.
Send CodeTransmits '119' (911 in reverse) followed by ANI code.
Alarm ToneOFFRadio speaker blocks alarm sound.
ONRadio speaker sounds an alarm.
ANI-Edit100View ANI ID, allows changing ANI ID.
GPSGPS On/OffOFFTurn off position system.
ONTurn on position system, press and hold MENU key to enter GPS mode.
Time Zone-12 to 0 to +12Set the time zone of the region.
GPS ModeGPSSelect GPS mode.
BDS
GPS+BDS
Channel Configuration
No.NameSettingDescription
1CH.NAMEChannel 1View/rename current channel. Use # key to switch input method.
2RX FrequencyView/change current RX frequency. Input by keypad, save with Menu key.
3TX FrequencyView/change current TX frequency. Input by keypad, save with Menu key.
4Trans PowerHighSelects HIGH TX power in VFO/Frequency mode.
MiddleSelects Middle TX power in VFO/Frequency mode.
LowSelects LOW TX power in VFO/Frequency mode.
5BandwidthWideWideband (25 kHz bandwidth).
NarrowNarrowband (12.5 kHz bandwidth).
6RX CTCSSOFF;67-254.1Mutes speaker if no specific continuous sub-audible signal.
7RX DCSOFF;023N-7541Mutes speaker if no specific low-level digital signal.
8TX CTCSSOFF;67-254Transmits specific continuous sub-audible signal to unlock squelch of distant receiver.
9TX DCSOFF;023N-7541Transmits specific low-level digital signal to unlock squelch of distant receiver.
10EncryptionOFFDisable encrypted mode, conversations are not private.
ONActivate encryption mode for privacy. Other radio must also have Encryption activated and same DCS code.
11Signaling1-20Selects 1 of 20 DTMF codes. Programmed with software, up to 3 digits each.
12CH-MDFNAMEMR/Channel mode displayed in NAME format.
FREQMR/Channel mode displayed in frequency format.
CHMR/Channel mode displayed in CH format.
13SP-MuteQTMonitor feature activated only when radio receives correct CTCSS/DCS.
14SCAN ADDOFFForbid current channel to join scan group.
ONAdd current channel to scan group.
15Busy LockoutOFFPTT button on channel always allowed.
ONDisables PTT button on channel. Transceiver sounds beep, won't transmit.
*13OffSet000Specifies difference between TX and RX frequencies.
*14DirectionNoneTX = RX (simplex). Disable access to repeaters.
PlusPlus frequency shift direction. TX shifted higher than RX.
MinusMinus frequency shift direction. TX shifted lower than RX.
16CH_MemoryCH001-CH100Create/modify existing channels (1-100) for MR/Channel Mode.
17CH_DeleteCH001-CH100Delete programmed information from specified channel (1-100).
7Radio InfoRadio ID\Firmware\HardwareDisplays radio ID, firmware version, hardware version.

5. Maintenance

5.1 Battery Maintenance

  • Only charge batteries in normal room temperatures.
  • When charging a battery attached to the radio, turn the radio off for a faster charge.
  • Do not unplug the power to the charger or remove the battery and/or radio before it's finished charging.
  • Never charge a wet battery.
  • Batteries wear out over time. If operating time decreases, consider a new battery.
  • Battery performance is reduced in freezing temperatures. Keep a spare battery warm.
  • Wipe battery contacts with a clean cloth regularly.
  • If the battery gets wet, remove it, wipe dry, and place in a plastic bag with dry rice overnight.

5.2 How to Store the Battery

  • Store battery at 80% discharged.
  • Keep in low temperature and dry environment.
  • Keep away from hot places and direct sunlight.
  • Cycle the battery at least every six (6) months during long-term storage.

NOTICE:

  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.

6. Troubleshooting Guide

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly.Remove and reattach the battery.
The battery power may run out.Recharge or replace the battery.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.Clean the battery contacts or replace the battery.
The battery voltage maybe low.Recharge or replace the battery.
During receiving, the voice is weak or intermittent.The volume level may be low.Increase the volume.
The antenna maybe loose or maybe installed incorrectly.Turn off the radio, and then remove and reattach the antenna.
The speaker maybe blocked.Clean the surface of the speaker.
You cannot communicate with other group members.The frequency or signaling type maybe inconsistent with that of other members.Verify that your TX/RX frequency and signaling type are correct.
You may be too far away from other members.Move towards other members.
You hear unknown voices or noise.You may be interrupted by radios using the same frequency.Change the frequency, or adjust the squelch level.
The radio in analog mode maybe set with no signaling.Request your dealer to set signaling for the current channel to avoid interference.
You are unable to hear anyone because of too much noise and hiss.You may be too far away from other members.Move towards other members.
You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area.Move to an open and flat area, restart the radio, and try again.
It may be the result of external disturbance (such as electromagnetic interference).Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.

7. Technical Specifications

GENERAL
Channel Capacity1000/10 Bank
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 18 hours @ 5 watts
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions182×67×41 mm (not including antenna)
Radio Weight350 g (with Li-ON battery)
TRANSMITTER
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450MHz (Canadian version)
144 to 146 MHz, 430 to 440MHz (European Union version)*
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
RECEIVER
Frequency RangeFM76-108MHz; AM108-136MHz;
VHF: 136-174 MHz; 220-260MHz; UHF:350-390MHz; 400-520 MHz;
Sensitivity: 12 dB SINAD-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

NOTE: All specifications may be modified without prior notice or liability. Thank you.

Table of UV-32 Specifications including Frequency, Channel Capacity, Channel Spacing, Dimensions, Weight, Operating Voltage, Antenna Impedance, Operating Temperature, and Storage Temperature.

Figure 14: UV-32 Specifications Summary

7.1 Additional Product Properties

  • Output Power(w): 5w-10w
  • Battery Capacity(mAh): High Capacity
  • Waterproof / Water-Resistant: No
  • Battery Included: Yes
  • Material: Plastic
  • Storage Channel: 1000
  • Frequency Range: Multi Band
  • Walkie Talkie Type: Portable
  • Is_Display: Yes
  • Maximum Range: 5km-10km
  • Origin: Mainland China
  • Function 1: Type-C Charger
  • Function 2: Air Band
  • Function 3: Bluetooth Wireless Programming
  • Function 4: GPS
Comparison table between BAOFENG UV-32 and UV-5R, highlighting features like Phone APP Programming, GPS, Channel Capacity, Max Power, NOAA & Airband, Flashlight, Frequency, Copy Frequency, and Type-C Charger.

Figure 15: UV-32 vs. UV-5R Feature Comparison

8. User Tips

  • Some users have noted that the actual power output might be closer to 7W, despite being advertised as 10W.
  • The GPS functionality has been reported by some users to be inaccurate or show incorrect locations (e.g., showing Yemen when in Brazil).
  • The radio is analog only, not digital DMR.
  • Ensure to check the specific antenna type and plug standard (EU/US) when purchasing, as different options are available.
  • The radio comes as a single unit, not a pair.
  • If you experience weak reception or noise, ensure your antenna is securely attached and consider adjusting the squelch level.
  • For Bluetooth programming, ensure both your phone's Bluetooth and the radio's GPS function are enabled in the menu.

9. Warranty and Support

For technical support or if solutions in the troubleshooting guide do not resolve your issues, please contact your dealer.

9.1 EU Declaration of Conformity

Baofeng and Pofung declare that the radio equipment type listed in Technical Specifications is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC. You can also contact your local Baofeng helpdesk, your dealer, or send an email to wangjianhui@baofengradio.com.

9.2 Manufacturer Contact Information

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com

Print version: UV32_CE_V1.0


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.