diymore RP2350 Tiny

Contents

RP2350 Tiny Microcontroller Development Board User Manual

Model: RP2350 Tiny | Brand: diymore

1. Introduction

The RP2350 Tiny is a compact microcontroller development board designed for embedded applications. It features the RP2350A dual-core, dual-architecture processor, offering high performance and versatility for a wide range of projects. This manual provides essential information for setting up, operating, and maintaining your RP2350 Tiny board.

Front and back view of the RP2350 Tiny Microcontroller Development Board
Figure 1: Front and back view of the RP2350 Tiny Microcontroller Development Board.

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always handle electronic components with care to prevent electrostatic discharge (ESD). Ensure proper ventilation when operating and avoid exposure to moisture or extreme temperatures.

3. Setup Guide

The RP2350 Tiny board is available as a standalone module or as a kit including an adapter board and FFC cable for easier prototyping.

3.1 Package Contents

Depending on your purchase, your package will include one of the following sets:

  • Set 1: 1 x RP2350 Tiny Single Board Development Board
  • Set 2: 1 x RP2350 Tiny Single Board Development Board, 1 x Adapter board, 1 x FFC line
RP2350 Tiny Kit showing the main board, adapter board, and FFC cable
Figure 2: The RP2350 Tiny Kit, including the main board, adapter board, and FFC cable.

3.2 Initial Connection

  1. For Kit Users (with Adapter Board): Connect the RP2350 Tiny board to the adapter board using the provided FFC cable. Ensure the cable is securely seated in both FPC connectors.
  2. Power Connection: Connect the adapter board (or the RP2350 Tiny directly if not using the adapter) to your computer using a USB Type-C cable. The board will be recognized as a high-capacity storage device.
Close-up of the adapter board connected to a USB Type-C cable
Figure 3: Connecting the adapter board to a computer via USB Type-C.

3.3 Custom Board Integration

The RP2350 Tiny board features a half-hole process design, allowing it to be directly welded onto custom PCBs. This enables seamless integration into your self-designed base plates.

4. Operating Instructions

4.1 Programming the Board

The RP2350 Tiny supports programming using C/C++ and MicroPython. Its design allows for quick and easy embedding into applications.

  • C/C++ SDK: The official CSDK can be used from the command line, or integrated with popular development environments like Visual Studio Code and Eclipse.
  • MicroPython: A full implementation of the Python 3 programming language that runs directly on embedded hardware.
Diagram illustrating support for C/C++ SDK and MicroPython
Figure 4: The RP2350 Tiny supports development with C/C++ SDK and MicroPython.

Drag and Drop Programming: When connected via USB, the board appears as a mass storage device. You can upload compiled programs (e.g., UF2 files for MicroPython) by simply dragging and dropping them onto the device drive.

4.2 GPIO Pinout

The RP2350 Tiny leads out 28 multifunctional GPIO pins. 20 of these pins can be accessed via pin headers, while the remaining pins are solderable for custom applications. Refer to the pinout diagram below for detailed pin functions.

Detailed pinout diagram for the RP2350 Tiny board
Figure 5: RP2350 Tiny Pinout Diagram. This diagram details the functions of each GPIO pin, including power, ground, UART, GPIO, PIO, PWM, USB, ADC, SPI, Debugging, System Control, and I2C connections.

Pin Function Overview:

  • Power: 5V, 3V3, GND
  • User Mode Selection Resistor: GP24, GP25, GND
  • WS2812 RGB LED Occupied pins: GP16, DIN
  • GPIOs (GP0-GP13, GP14-GP19, GP20-GP29): Multifunctional pins supporting various protocols.
  • Peripherals:
    • SPI: SPIO RX/CSn/SCK/TX, SPI1 RX/CSn/SCK/TX
    • I2C: I2C0 SDA/SCL, I2C1 SDA/SCL
    • UART: UARTO TX/RX, UART1 TX/RX
    • ADC: ADC0, ADC1, ADC2, ADC3

4.3 Low-Power Modes

The RP2350 Tiny supports low-power sleep and deep sleep modes, allowing for efficient power management in battery-powered applications. Refer to the RP2350A datasheet for detailed implementation of these modes.

5. Maintenance

  • Keep the board clean and free from dust and debris.
  • Avoid exposing the board to liquids or high humidity.
  • Store the board in an anti-static bag when not in use to prevent ESD damage.
  • Do not apply excessive force to connectors or components.

6. Troubleshooting

  • Board not recognized by computer: Ensure the USB Type-C cable is fully inserted and functional. Try a different USB port or cable.
  • Program upload failure: Verify your code compiles without errors. Ensure the board is in the correct mode for program upload (e.g., by holding the BOOT button during power-up if required by your specific toolchain).
  • Unexpected behavior: Double-check your wiring and pin assignments against the pinout diagram. Review your code for logical errors.

7. Specifications

The RP2350 Tiny is built around the powerful RP2350A microcontroller. Key components are highlighted in the diagram below.

Component overview of the RP2350 Tiny board with labeled parts
Figure 6: RP2350 Tiny Component Overview. Key components include the FPC Connector, LDO, NOR-Flash, RP2350A processor, and WS2812 RGB LEDs.
Table 1: RP2350 Tiny Technical Specifications
Feature Description
Processor RP2350A (Dual-core ARM Cortex-M33, Dual-core 3 RISC-V, up to 150MHz)
Memory 520KB SRAM, 4MB On-chip Flash
Interfaces USB 1.1 Host and Device (Type-C), Onboard FPC 8PIN interface
GPIO Pins 28 multifunctional GPIO pins (20 via pin headers, rest solderable)
Peripherals 2 SPI, 2 I2C, 2 UART, 4 12-bit ADCs, 16 controllable PWM channels, Temperature sensor, On-chip accelerated floating-point library, 12 Programmable I/O (PIO) state machines
Dimensions (Motherboard) 23.5mm x 18mm x 2.1mm (0.93in x 0.71in x 0.08in)
Dimensions (Adapter Board) 18mm x 18mm x 4.2mm (0.71in x 0.71in x 0.17in)
Dimensions diagram for the RP2350 Tiny board and adapter board
Figure 7: Physical dimensions of the RP2350 Tiny board and its adapter board.

8. User Tips

  • For initial development and prototyping, consider using the adapter board and FFC cable for easier access to pins and USB connectivity.
  • Leverage the drag-and-drop programming feature for rapid iteration and testing of your code.
  • Explore the extensive documentation and community resources available for RP2040-based microcontrollers, as many concepts and libraries are transferable to the RP2350 Tiny.

9. Frequently Asked Questions (FAQ)

Q: What programming languages does the RP2350 Tiny support?
A: It supports C/C++ and MicroPython.
Q: How do I upload programs to the board?
A: The board appears as a mass storage device when connected via USB, allowing you to drag and drop compiled program files (e.g., UF2 files) directly onto it.
Q: Can I integrate the RP2350 Tiny into my own custom PCB?
A: Yes, its half-hole process design allows for direct soldering and integration into custom base plates.

10. Further Information and Support

For more detailed technical information, datasheets, and advanced programming guides, please refer to the official documentation.

A comprehensive user manual in PDF format is available for download: RP2350 Tiny User Manual (PDF).

For product support or inquiries, please contact the manufacturer or your point of purchase.

© 2023 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.