1. Introduction
The Estardyn D1 Mini ESP32 is a compact and powerful Internet of Things (IoT) development board, integrating Wi-Fi and Bluetooth capabilities. Based on the ESP32-WROOM-32 module, it offers a versatile platform for a wide range of applications, from smart home devices to complex sensor networks. This manual provides essential information for setting up, operating, and maintaining your D1 Mini ESP32 board.
2. Package Contents
Upon opening your package, please verify that all items are present and in good condition:
- Estardyn D1 Mini ESP32 Development Board (Type-C or Micro USB version)
- Pin Headers (typically 2x 16-pin headers for soldering)

3. Product Overview
The D1 Mini ESP32 board is designed for ease of use and integration into projects. It features a compact form factor similar to the popular Wemos D1 Mini, but with the enhanced capabilities of the ESP32 chip.

3.1 Key Features
- ESP32-WROOM-32 module with integrated Wi-Fi and Bluetooth
- Compact size (39mm x 31mm)
- USB-to-Serial converter (CP2104 or CH9102) for easy programming
- Multiple GPIO pins for various peripherals
- Support for various development environments (Arduino IDE, PlatformIO, ESP-IDF)
- Available with Type-C or Micro USB connector
3.2 Pinout Diagram
Understanding the pinout is crucial for connecting external components and programming the board. Refer to the diagram below for detailed pin assignments.

Key Pin Functions:
- Power Pins: GND (Ground), VCC (3.3V or 5V depending on power source, typically 3.3V for ESP32 logic).
- Serial Communication: TXD (Transmit Data), RXD (Receive Data) for UART communication.
- GPIO Pins: Numbered pins (e.g., IO27, IO25, IO32, IO4, IO0, IO2, IO5, IO18, IO19, IO23, IO34, IO35, etc.) are General Purpose Input/Output pins. These can be configured for various functions like digital input/output, ADC, DAC, I2C, SPI, UART, PWM, etc.
- Special Pins:
- RST: Reset pin.
- EN: Enable pin.
- BOOT/IO0: Used for entering bootloader mode.
- SD_CMD, SD_CLK, SD_D0, SD_D1, SD_D2, SD_D3: Pins for SD card interface.
- Touch: Capacitive touch pins (e.g., IO32, IO33, IO27, IO25, IO26, IO4, IO0, IO2, IO15, IO13, IO12, IO14).

4. Initial Setup
Before you can start programming your D1 Mini ESP32 board, you need to perform some initial setup steps.
4.1 Driver Installation
The board uses either a CP2104 or CH9102 USB-to-Serial chip. You may need to install the appropriate drivers for your operating system (Windows, macOS, Linux).
- CP2104 Driver: Search for "CP210x USB to UART Bridge VCP Drivers" online.
- CH9102 Driver: Search for "CH9102 USB-Serial Driver" online.
After installation, connect the board to your computer using a compatible USB cable (Type-C or Micro USB). The board should appear as a serial port in your device manager (Windows) or under /dev/ttyUSBx or /dev/cu.usbserial-xxxx (Linux/macOS).

4.2 Development Environment Setup (Arduino IDE Example)
- Install Arduino IDE: Download and install the latest version of the Arduino IDE from the official Arduino website.
- Add ESP32 Board Manager URL:
- Go to File > Preferences.
- In the "Additional Board Manager URLs" field, add:
https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json - Click OK.
- Install ESP32 Boards:
- Go to Tools > Board > Boards Manager.
- Search for "ESP32" and install the "esp32 by Espressif Systems" package.
- Select Board: Go to Tools > Board > ESP32 Arduino and select "ESP32 Dev Module" or a similar generic ESP32 board.
- Select Port: Go to Tools > Port and select the serial port corresponding to your D1 Mini ESP32 board.
5. Operating Instructions
Once your development environment is set up, you can upload your first program (sketch) to the D1 Mini ESP32.
5.1 Uploading a Basic Sketch (Arduino IDE)
- Open an Example: Go to File > Examples > 01.Basics > Blink. This will open a simple sketch that blinks an LED.
- Verify Code: Click the "Verify" button (checkmark icon) to compile the code and check for errors.
- Upload Code: Click the "Upload" button (right arrow icon) to compile and upload the sketch to your D1 Mini ESP32 board.
- During upload, you might need to press and hold the "BOOT" button (often labeled "IO0" or "FLASH") on the board, then press "RST" (reset), release "RST", and then release "BOOT" once the upload starts. Some boards automatically enter programming mode.
- Observe: If successful, the onboard LED (if present and connected to the correct GPIO) should start blinking. You can also open the Serial Monitor (Tools > Serial Monitor) to see any output from your program.
5.2 Connecting Peripherals
Use the pinout diagram (Section 3.2) to connect sensors, actuators, and other modules to the appropriate GPIO pins. Ensure you respect voltage levels (ESP32 GPIOs are typically 3.3V tolerant) and current limits.
6. Maintenance
To ensure the longevity and reliable operation of your D1 Mini ESP32 board, follow these simple maintenance guidelines:
- Storage: Store the board in a dry, anti-static environment, away from direct sunlight and extreme temperatures.
- Handling: Avoid touching the pins and components directly to prevent electrostatic discharge (ESD) damage. Use anti-static precautions when handling.
- Cleaning: If necessary, gently clean the board with a soft, dry brush or compressed air. Do not use liquids or abrasive materials.
- Power Supply: Always use a stable and appropriate power supply (typically 5V via USB or 3.3V via VIN pin) to prevent damage.
7. Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause / Solution |
|---|---|
| Board not detected by computer |
|
| Failed to upload sketch |
|
| Wi-Fi/Bluetooth not working |
|
| Random resets or crashes |
|
8. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Estardyn |
| Model | D1 Mini ESP32 (based on ESP32-WROOM-32) |
| Connectivity | Integrated Wi-Fi (802.11 b/g/n) and Bluetooth (v4.2 BR/EDR and BLE) |
| USB-to-Serial Chip | CP2104 or CH9102 (variant dependent) |
| USB Connector Type | Type-C or Micro USB (variant dependent) |
| Operating Voltage | 3.3V (from onboard regulator) |
| Input Voltage (USB) | 5V |
| Application | Computer, IoT Development |
| Package | SMD |
| Dimensions (Main Board) | Approx. 39mm x 31mm (main board width 22.86mm) |
| Condition | New |
| Origin | Mainland China |
9. User Tips
- Start Simple: Begin with basic examples like blinking an LED or connecting to Wi-Fi to familiarize yourself with the board and development environment.
- Power Considerations: While USB provides power, for projects involving many sensors or high-power components, consider providing external 3.3V or 5V power to the appropriate pins for stability.
- Community Support: The ESP32 community is vast and helpful. Utilize online forums, documentation, and tutorials for project ideas and troubleshooting.
- Pin Usage: Be aware that some GPIO pins have specific functions during boot or are connected to internal components. Refer to Espressif's official ESP32 documentation for advanced pin usage guidelines.
10. Warranty and Support
For technical support, documentation, or inquiries regarding your Estardyn D1 Mini ESP32 development board, please refer to the manufacturer's official website or contact their customer service. Keep your purchase records handy for any warranty claims.