AnyTone AT-D168UV

Contents

Anytone AT-D168UV Digital DMR and Analog UHF/VHF Amateur Two Way Radio

Model: AT-D168UV | Brand: AnyTone

1. Introduction

Thank you very much for choosing our AnyTone Dual Band Digital DMR and Analog two-way radio. This radio adopts the latest advances in technology, providing reliable communication in today's demanding communication environment.

This radio offers both DMR digital and analog communication, introduces innovative DMR digital processing system to achieve SMS, high-audio quality and digital encryption. It offers great stability and reliability, together with long-distance communication as well as fashionable design and compact exterior lines. The AT-D168UV has Text Messaging, Recording, Voice Message, Digital Encryption, Emergency Alarm, Work Alone Roaming, Vibration, Analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode functions.

Note on CPS (Computer Program Software):

  • When using CPS to program the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequencies and settings to a new saved code plug. Failure to do so may result in errors.
  • The CPS allows you to program frequency, channel type, power, etc. Ensure your programming complies with your FCC (or other country) license certification.

2. Unpacking and Checking the Equipment

Unpack the radio carefully. We recommend that you identify the items listed below before discarding the packing materials. If any items are missing or have been damaged during shipment, please contact the carrier or the dealers immediately.

2.1 Supplied Accessories

ItemQuantity
Antenna2
Li-ion Battery Pack2
Battery Charger1
AC Adaptor1
TYPE C Cable1
Belt Clip1
Instruction Manual1

2.2 Standard Accessories Visual Guide

The following images illustrate the standard accessories included with your AT-D168UV radio:

12cm and 38cm Antennas
12cm Antenna (TX-0311) and 38cm Antenna (TX-0313)
Li-ion Battery Packs
Li-ion Battery Packs (QB-56L 1800mAh, QB-56HL 2600mAh)
Charger and AC Adaptor
Charger (QBC-56L) and AC Adaptor (NA01 5V/2A)
Type C Cable
TYPE C Cable (QT-0046) for Program and Charge
Belt Clip
Belt Clip (WWZZ-0029)
Instruction Manual
Instruction Manual

Note: For the frequency band of the antenna, please refer to the label indicated on the bottom of the antenna.

2.3 Optional Accessories

Optional accessories are available to enhance your radio's functionality:

Multi-charger
Multi-charger (BC-158-4)
Speaker Microphone
Speaker Microphone (QHM-024)
Earphone
Earphone (EJX-0012)
Wrist strap
Wrist strap

3. Radio Overview

3.1 Radio Components

Front view of the AT-D168UV radio with labeled components: Antenna, Channel Switch, POWER/VOL knob, LED Status Indicator, LCD, Menu key, Speaker, Exit Key, MIC.
Front view of the AT-D168UV radio with labeled components: Antenna, Channel Switch, POWER/VOL knob, LED Status Indicator, LCD, Menu key, Speaker, Exit Key, MIC.
Side views of the AT-D168UV radio with labeled components: Speaker/Mic Jacks, Type C port (Program and charge), PTT Button, [PF1] Key, [PF2] Key.
Side views of the AT-D168UV radio with labeled components: Speaker/Mic Jacks, Type C port (Program and charge), PTT Button, [PF1] Key, [PF2] Key.

3.2 LCD Display

LCD display of the AT-D168UV showing various icons and information like Bluetooth, Roaming, BT PTT, VOX, Dig Monitor, GPS, Inbox, Auto Power Off, Battery, TX Power, Color Code, current frequency, zone, and menu options.
LCD display of the AT-D168UV showing various icons and information like Bluetooth, Roaming, BT PTT, VOX, Dig Monitor, GPS, Inbox, Auto Power Off, Battery, TX Power, Color Code, current frequency, zone, and menu options.

3.3 Status Indications (LED)

The top LED indicator helps identify the current radio status:

LED IndicationStatus
Flashes RedLow battery voltage
Constant RedTransmitting
Constant GreenAnalog Receiving
Constant CyanDigital Receiving
Flashes GreenScan

4. Battery Information

4.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity reaches its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.

4.2 Charger Supplied

Please use the specified charger provided by AnyTone. Other models may cause explosions and personal injury. After installing the battery pack, and if the radio displays low battery with a red flashing lamp or voice prompt, please charge the battery.

4.3 How to Charge

The radio uses a USB-C cable for charging. The USB-C cable can be inserted into the USB-C port on the radio for direct charging to the battery. Do not transmit with the radio while the charger/programming cable is plugged into the side of the radio. This may damage the unit.

The USB-C cable can also be inserted into the USB-C port on the desktop charger. The standard 5V/2A USB-C adapter is commonly available.

  1. Plug the AC adaptor into the AC outlet, and then plug the cable into the USB-C port located on the back of the charger. The indicator lights green and is then ready to charge a battery.
  2. Plug the battery or the radio into the charger. Make sure the battery terminals are in good contact with the charging terminals. The indicator light turns red, indicating charging has begun.
  3. It takes approximately 2.5 hours for the QB-56L thin battery to be fully charged, and 3.5 hours for the QB-56HL thick battery to be fully charged. When the lamp lights green, charging is completed. Remove the battery or the radio unit with its battery from the socket.
Diagram showing the charging setup for the AT-D168UV radio, including AC adapter, USB-C cable, and desktop charger.
Charging setup for the AT-D168UV radio.

Note:

  • When charging a radio (with battery) while it is powered on, the indicating lamp will not turn green to show the fully charged status. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is powered on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. Therefore, the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

4.4 Use Caution with the Li-ion Battery

  • Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as AnyTone cannot be held responsible for any accident caused by modifying the battery.
  • The ambient temperature should be between 5°C - 40°C (40°F - 105°F) while charging the battery. Charging outside this range may not fully charge the battery.
  • Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
  • To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on.
  • Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
  • Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.

4.5 How to Store the Battery

  • If the battery needs to be stored, keep it in a status of 80% discharged.
  • It should be kept in a low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.

Warning:

  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.
  • Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

5. Preparation

5.1 Installing / Removing the Battery

  1. Match the two top grooves of the battery pack with the corresponding guides on the back of the radio and then push it.
  2. To remove the battery pack, slide the release latch at the bottom away from the battery and remove the pack from the transceiver.

5.2 Installing / Removing the Antenna

  1. Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  2. Removing the Antenna: Turn the antenna counter-clockwise to remove it.

5.3 Installing / Removing the Belt Clip

  1. Installing the Belt Clip: Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.
  2. Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.

5.4 Installing the Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

6. Basic Operations

6.1 Power on the Radio

Turn on the radio by turning the [Power/Volume] switch clockwise until a click is heard. The LCD will display a start-up message, and you will hear a beep after 7 seconds.

6.2 Adjust Volume

Rotate the [Power/Volume] knob to adjust the volume. Turn clockwise to increase volume and counterclockwise to decrease the volume. The LCD display will show the volume status during an adjustment.

6.3 Main Band/Sub Band Switch

Press the key programmed as Main CH Switch to switch the main channel to the other channel if there are 2 channels shown on the display. The channel with bold characters is the main channel.

6.4 VFO/Channel Switch

Press the key programmed as VFO/MR to switch between VFO and channel display.

6.5 Set Up VFO Frequency

Turn the radio to VFO mode using the key programmed as VFO/MR. The VFO frequency can only be set up when the channel is in the main “bold text” channel.

  • Operation 1: Input the VFO frequency directly by the keyboard.
  • Operation 2: Turn the channel selector to adjust the VFO frequency steps.

6.6 Select a Channel

Press the key programmed as VFO/MR to switch the radio between VFO and Channel mode, then select Channel mode.

  • Operation 1: Turn the channel switch to select a channel.
  • Operation 2: Input the channel numbers by the keyboard. For example, to switch to channel 99, input 0+0+9+9 (a total of 4 digits), and it will switch to channel 99.

A channel can either be Analog or Digital. For analog channels, the Push-To-Talk button is always available. On Digital Channels, parameters can be set up by users/system operators by individual channel to allow talk permit. There are four possible settings that can be selected in the CPS channel:

  1. Always Allow: The user can transmit all the time.
  2. Channel Free: The radio can transmit only if the channel is free.
  3. Different Color Code: The radio can transmit if the channel is free, but the color code is mismatched.
  4. Same Color Code: The radio can transmit only if the channel is free and the color code matches.

6.7 New Channel

  1. Press the Menu key to enter the main Menu.
  2. Select "Settings".
  3. Select "Chan Set".
  4. Select "New Chan".
  5. Input the channel number by keypad, then press the confirm key.
  6. Select a zone from the zone list, then Confirm To Save. The radio will start channel saving, and saving is completed when it displays "Saved".
  7. Now select the new channel in the radio and go to Channel Settings menu to set up all the new channel's parameters.

6.8 Delete Channel

  1. In channel (MR) mode, press the Menu key to enter the main Menu.
  2. Select "Settings".
  3. Select "Chan Set".
  4. Select "Delete Chan" to delete the current channel.

6.9 Receiving and Responding to a Radio Call

When the radio is in digital mode, it can receive and respond to a call with the same frequency/color code/slot. When receiving a call:

  • If the radio is programmed with the caller's DMR ID number in the digital contact list, the radio will ring or vibrate briefly.
  • The cyan LED lights up.
  • The bottom of the LCD shows the received signal strength (RSSI), and the LCD display will show the DMR ID/name/city/state/country/call type and incoming icon based on what is in the contact list.
  • When the call is ended, it will display "Call end", and you can press [PTT] to respond to the call.

6.10 Making a Call

Method 1: From the Channel Switch

Turn the channel switch to choose a programmed channel.

Method 2: From the Talk Group

  1. Turn the channel switch to choose a programmed channel.
  2. Press the Exit key to enter the TG List, press the Up/Down key to choose a TG.

Method 3: From the Keypad

  1. Turn the channel switch to choose a programmed channel.
  2. Press the Menu key to Talk Group, press select to enter TG.
  3. Press the Up/Down key to Manual Dial, press Select.
  4. Input the ID number by keypad, press the # key to switch group ID or Private DMR ID.

Hold the radio vertically 2.5-5cm from your mouth, press the [PTT] key to start the call. The red LED lights up, the receiver ID/name/city/state/country/call type and call out icon will be displayed on the LCD if the digital database is up-to-date in the radio. Release [PTT] key to receive the reply.

6.11 Monitor

In standby, press the key programmed as Monitor to enter Monitor. When receiving a matched carrier but the signaling / ID is unmatched or the signal is too weak, this function allows monitoring of weak signals and signals with unmatched IDs. Press the key again to shut off the speaker and return to standby.

Note:

  • When in analog mode, if no signal, it will emit a noise when pressing the Monitor Key. The Rx icon is seen when monitor is activated.

6.12 Emergency Alarm

Press the key programmed as Alarm to turn on the alarm function, then press this key again to return to normal operation.

6.13 Battery Voltage Test

Press the key programmed as Voltage function to check the current battery voltage, then press this key again to return.

7. Advanced Features and Main Menu Functions

7.1 Programmed Keys (PF1, PF2)

It is possible to set different functions for [PF1] and [PF2] keys.

  • Method 1: In radio Menu > Settings > Radio Set > Key > PF1, PF2.
  • Method 2: In PC software > Public > Optional Setting > Key function.
FunctionDescription
OFFNo Function
VoltCheck the current battery capacity voltage
Tx PowerSwitch the power between super high, high, middle and low power.
Talk AroundSwitch between Talk Around and Repeater mode
ReverseTurn on/off the frequency reverse function.
EncryptionChoose the digital encryption group for digital channel
CallIn Analog mode, send the DTMF/5TONE/2TONE encode. This function is only valid for analog channel.
VOXSet up the VOX level
VFO/MRSwitch between VFO mode and memory channel mode.
Sub PTTSub channel PTT, press to start the call on sub channel (NOTE: On PF1 - PF2 Keys Only)
ScanPress the key to start or stop scanning the channels in scan list.
FM RadioFM radio on/off
AlarmLong press the key to start alarm, short press again to exit the alarm.
Record SwitchEnable/disable the recording function
RecordStart/stop recording. When stop recording, the radio will remind repeat or send the record.
SMSIn digital mode, press to enter into SMS messages
DialStart the manually dial
GPS Info (optional)Check the GPS position information
MonitorMonitor the weak signal or the signal with unmatched ID.
Main CH SwitchChoose channel A or channel B as the main channel
Hot Key 1~6Selects Hot Keys 1-6 (details on next page)
Work AloneTurn on/off the work alone function.
Nuisance DeleteDuring scanning, press the key to skip the unwanted channel
Digi MonitorIn DMR mode, press the key to turn on/off digital monitor
Sub CH HideTurn on/off the sub channel
Prior ZoneSwitch to Priority Zone
VFO ScanPress the key to start or stop the VFO scan. The VFO scan start and end frequency should be set in CPS - Optional Setting - VFO Scan.
MIC SoundIn digital channel, switch the microphone tone to normal or enhanced mode.
LastCall ReplyIn digital channel, press the key to access the last call and press PTT to call back.
Switch Ch TypeSwitch the channel type (Analog, Digital, Ana+Dgi, Dgi+Ana)
RangingWhen the radio receives a call and the suspension time is on, press the key programmed as "Ranging" to obtain the caller's position and distance. (Both parties need GPS positioned, or will receive only GPS information)
RoamingIn standby, press the key programmed as "Roaming" to search and lock on the repeater with the strongest signal. (Note: After locking on a repeater, the radio will return to the last frequency only after the channel or frequency is changed. The repeater frequency list must be pre-programmed in CPS.)
Channel RangingIn standby, if the call contact type for a channel is "Private call", press the key programmed as "Channel Ranging" to turn on this function. The radio will automatically start the ranging function when turned to this channel.
Max VOL SetIn standby, press the key programmed as "Max Volume", will enable users to set the maximum RX volume.
Slot SetChoose Slot for current channel, this function is only valid in repeater mode.
Aprs TypeChoose Aprs Type for current channel.
Zone SelectIn standby, press the programmed "Zone Select" key, it will allow you to input the zone number and then press the confirm key to switch to the zone.
Roaming SetSets Roaming Function
APRS Set (optional)Sets APRS Function
Mute TimingPress the key to mute the radio for a set time. The mute timing should be set in CPS - Optional Setting - Other - Mute Timing.
CTC/DCS SetSet the CTCSS/DCS for analog channel
TBST SendSend the TBST Tone
BT On/Off (optional)Enable / disable the Bluetooth function
GPS On/Off (optional)Enable / disable the GPS function
Ch. NameSwitch between channel name display and frequency display for the current channel
CDT ScanEnable / disable the CTCSS/DCS scanning for the analog channel. When the radio finds matched CTCSS/DCS for the current channel, it will open the speaker and start receiving. Only analog channels with CTCSS/DCS signaling can start CDT scanning.
ARPS Send (optional)Manually transmit the APRS at the current channel.
DIM ShutLight up or turn off the display/indicator.
GPS Roam (optional)Enable / disable the GPS roaming function.
WX AlarmEnable / disable the weather alarm function.
SQ LevelSet the squelch level.

7.2 Combination Key Function

Press the Menu key and hold until the LCD displays “Next Please Press Dial Key”, then press the number key. It will perform the programmed function. Combination key functions must be set up in PC software-Public-Hot key.

7.3 Access Advanced Features for Private Calling

Method 1: To Access a Private Call from the Contact list

  1. Press the Exit key to enter the Talk Group, press the Up/Down key to a private DMR call ID name.
  2. Press Select to View Contact, press Select to see the contact information.
  3. Press Option to access the advanced features.

Method 2: Access from Manual Dial

  1. Press the Menu key to enter Talk Group, press the Up/Down key to Manual Dial.
  2. Press Select to enter Manual Dial.
  3. Input the Private DMR ID, press Option to access the advanced features.

7.4 Set up Advanced Features for Private Calling

7.4.1 Call Alert

Select Call Alert. It will send out a call alert. The target radio will sound a beep or vibrate when receiving the call alert, and it will return a success or failed call message to the transmit radio.

7.4.2 Remote Ranging

Select Remote Ranging. It will send out a signal for the target radio to turn on its microphone and transmit when receiving the signaling. It will send back the voice to the transmit radio. With this feature, you can monitor the sound activity near the target radio remotely.

7.4.3 Get GPS Info (Optional)

Select Get GPS info. It will send out a signal to the target radio, which will start GPS positioning and send a message of its GPS position to the transmit radio.

7.4.4 Check Radio

Select Check Radio. It will send out a radio check to the target radio, which will send back a message if it is available or not available to the transmit radio. With this feature, you can determine if another radio is active and powered on in the system.

7.4.5 Kill

Select Kill. It will send out a kill signaling to the target radio, which will be killed (No display, no operation) when receiving the signaling, and it will send back a kill successful message to the transmit radio.

7.4.6 Wake

Select Wake. It will send out a wake-up signaling to the killed radio, and the target radio will return to standby when it receives this signaling and send back a Wake successful message to the transmit radio.

7.4.7 Ranging (Optional)

When both caller and receiver are GPS positioned, if the caller turns on the ranging function and the receiver is within communication range, the transmit radio will detect the distance and direction between two radios at fixed intervals, and then show the information on the display of the transmit radio.

7.5 Main Menu Functions

7.5.1 Talk Group

  • TG List: Displays the talk group (TG) list programmed in the PC software. This list is used as a look-up table to display contact TG information when receiving a call.
  • New Contact: Allows you to create a new TG.
  • Manual Dial: Input the group ID or private DMR ID to access a TG quickly.
  • Talker Alias: Allows Alias transmit Set / Alias receive Set.

7.5.2 SMS

  • New Msg: Create a new message and send to a contact.
  • InBox: Shows all received messages, and allows forwarding or deleting the message.
  • OutBox: Shows all sent messages, and allows resending, forwarding or deleting the message.
  • Quick Text: Pre-saved messages, and allows sending, editing or deleting the message.
  • Draft: Draft messages, and allows sending, editing or deleting the draft message.

7.5.3 Call Log

  • Last Call: The Last Call List shows the last caller DMR ID and time information. It allows you to save the last caller as a new contact if it is not in your contacts.
  • Sent: The Sent List shows sent messages until selected and deleted.
  • Answered: Shows all answered calls, and allows deleting the call record or saving the DMR ID as a new contact.
  • Missed: Shows all missed calls, and allows deleting a call record or saving the DMR ID as a new contact.

7.5.4 Zone

A Zone is a group of channels grouped together. The AT-D168UV DMR radio has 250 Zones. A Zone can have a maximum of 160 analog and/or digital channels.

7.5.4.1 Select a Zone

  • Operation 1: Press the Up/Down key directly to switch the zone. The LCD will display the selected zone number or name.
  • Operation 2:
    1. Press the Menu key to enter the main Menu.
    2. Select "Zone".
    3. Select a zone from the zone list. The radio will change to the selected zone.

7.5.4.2 Add Zone

  1. Press the Menu key to enter the main Menu.
  2. Select "Zone".
  3. Select "Add Zone".
    1. Edit name: Input the zone name by keypad, press the Delete key to delete. After editing the correct name, press the Confirm key to confirm and store.
    2. Edit Chan: Select "Add Chan" then select a channel from the list.
    3. Save: Press the Save key to store the new zone.

7.5.4.3 Delete Zone

  1. Press the Menu key to enter the main Menu.
  2. Select "Zone".
  3. Select a Zone from the zone list.
  4. Select Delete Zone to delete the current zone.

7.5.5 Scan

In the PC software > Public > Scan list, it allows saving 250 scan lists and programming the required scan lists and writing them into the radio. Switch the radio to channel mode, as the scan list is only valid in channel mode.

7.5.5.1 Turn On Scan

  1. Press the Menu key to enter the main Menu.
  2. Select "SCAN".
  3. Select "Scan ON/OFF".
  4. Select "ON". The radio will start scanning. Press any key to stop scanning.

7.5.5.2 Scan List Operation

  1. Press the Menu key to enter the main Menu.
  2. Select "SCAN".
  3. Select "Scan List".
  4. Select a scan list and press the Enter key to enter the scan list sub menu.

Add Scan List to enter Sub Menu

  1. Select Cur Chan, and press the Enter key to add the current channel to the active list.
  2. Add Channel into Scan List: Select "Add Chan", then select "channel X" to add it into the scan list.
  3. Edit Scan List Name: Select "Edit Name". Input or revise the name and press the confirm key to store.
  4. Store List: Save the current list.
  5. Delete Channel from Scan List: Select "Channel X", then select "Delete CH" to remove it from the scan list.

7.5.5.3 Add Scan List

  1. Press the Menu key to enter the main Menu.
  2. Select "SCAN".
  3. Select "Scan List".
  4. Select "Add Scan List".
  5. Select "Add Chan", to add wanted channels into the new scan list.
  6. Select "Edit Name", input the name and confirm.
  7. Select "Store List" to save the new list.

7.5.6 Roaming

The Roaming function enables users to search the roaming channel list by a programmed time interval and lock onto the repeater with the strongest signal.

7.5.6.1 Roaming On/Off

Allows you to turn on roaming manually. After roaming is finished, it will return to the off state. **Manually Roaming is a one-time action only.**

7.5.6.2 Roaming Zone

Select Roam Test Zone: Select a Roaming Zone from the list to set it as the active zone. You can also scroll down the list of Zones and select Add Channel to add a new channel to the current Roaming Zone and set the parameters.

  • Select Add Channel: Add a new roaming channel to the current zone.
  • New Roam Ch: Allows you to modify the RX frequency/TX frequency/CC/TS/CH name for the roaming channel. Also allows you to remove the roaming channel from the zone.
  • Edit Name: Edit the zone name.
  • Select Zone: Select the roaming zone for the current channel.
  • Delete Zone: Delete the roaming zone from the current channel.

7.5.6.3 Auto Roaming Settings

Set the fixed time waiting interval to begin automatic roaming when the repeater cannot be found. Roaming will begin at the end of this time.

  • Fixed Time Set: The roaming will be started at a preset fixed time or set to off.

7.5.6.4 Repeater Check - Off / On

Turning on this function will allow the radio to check the repeater status. The "Repeater is out of range" icon shows if the repeater is not in range.

7.5.7 Settings

7.5.7.1 Radio Set

1. Voice Func

  • (1) Beep Tone: Beep On (radio beeps when you press keypad), Beep Off (no beep).
  • (3) Digi Idle: Set on if you want a tone when the digital channel is free.
  • (4) Ana Idle: Set on if you want a tone when the analog channel is free.
  • (5) Startup Sound: Set On if you want a tone when powering on.
  • (6) Talk Permit: Select if you want a tone confirming Digital and/or Analog repeater connection at the start of a call.
  • (7) D-Reset Tone: Select Off or On. Digital calls have a group call hold time and a private call hold time to prevent voice missing after the call. When set to On, it will beep when the hold time terminates.
  • (8) Max Vol Level: Indoor (very low volume), Level 1-8 (adjustable max volume).
  • (9) Headset Max Vol: Indoor (very low volume), Level 1-8 (adjustable max volume for earphone). Automatically changes to earphone maximum volume when connected.
  • (10) MIC Sound: Normal (low pitch), Enhance (high pitch).
  • (11) SMS Prompt: Different prompt options when receiving a new message.
  • (12) Call Ring: Different prompt options when receiving a new call.
  • (13) DigiMic Level: Digital mic level selection (1-5, Auto). Auto helps make TX digital audio similar, reducing loud audio and amplifying soft audio.
  • (14) AnaMic Level: Analog mic level selection (1-5, Auto). Auto helps make TX analog audio similar, reducing loud audio and amplifying soft audio.
  • (15) Fix Time Mute: With this function activated (On), it is possible to mute the loudspeaker for a special time segment. The duration of the "Mute Time" may be set by the CPS > Optional Setting > Other > Mute Timing.
  • (16) TX NR: Enabling the TX noise reduction function can reduce background noise and ambient noise in transmitted audio.
  • (17) Ana RX NR: Enabling the RX noise reduction function can reduce background noise and ambient noise in received analog audio.
  • (18) RX AGC: Enable the RX AGC function. It helps to make the RX audio similar, reducing loud audio and amplifying soft audio.

2. Display Func

  • (1) Back Light: LCD backlight intensity is adjustable in 5 steps.
  • (2) Night Mode: With this function ON, and when the radio is in standby, it will reduce the backlight to level 1, regardless of the backlight brightness setting.
  • (3) Light Time: Always (backlight always on), 5Sec-5Min adjustable. Note: This function is valid when turning off power save.
  • (4) Ch. Name: CH name (radio works in channel mode and displays channel name, programmed VFO/MR key is not valid), Frequency (radio works in VFO mode and displays frequency, programmed VFO/MR key switches VFO and Memory channels).
  • (5) Language: Choose Chinese or English.
  • (6) Menu Exit Time: 50Sec-60Sec. When entering the menu, the radio stays in the menu for the set time. When the time is reached, the radio auto exits the menu.
  • (7) Start Display: Picture (displays AnyTone picture when powered on), Character (displays characters set up in PC software), Customer's Pic (displays picture uploaded by PC software, resolution 128*160).
  • (8) CH Background: Default Picture (displays default picture), Customer's Pic (displays picture uploaded by PC software).
  • (9) CHG Font Color: Set the text color of the standby interface (8 colors available).
  • (10) CH Color A: Set color for band A channel display.
  • (11) CH Color B: Set color for band B channel display.
  • (12) Zone Color A: Set color for band A zone display.
  • (13) Zone Color B: Set color for band B zone display.
  • (14) Main Ch: Channel A (upper displayed channel becomes main), Channel B (lower displayed channel becomes main).
  • (15) Sub Ch Off: Sub Channel On (displays both channels), Sub Channel Off (displays main channel only).

3. Key Func

  • (1) Key Lock: Manual Lock (long press key to lock/unlock), Auto Lock (radio auto locks when standby). Note: Some options must be ON in CPS > Optional Setting > Key function for key lock to work. Knob Lock, Keypad Lock, Side Key Lock, Forced Key Lock options available.
  • (2-11) Key PF1, PF2: PF1 and PF2 keys are programmable for Short, Long1, or Long2 functions.

4. Other Func

  • (1) Auto Power Off: Allows setting automatic power off after 10 minutes, 30 minutes, 1 hour, or 2 hours of inoperation. Off disables the function.
  • (2) TX Timer: 30Sec-240Sec. TX is limited for the set time. Radio auto stops transmission when time is reached. OFF disables the TX time limit.
  • (3) TOT (Transmitter Out Timer) Predict: With this function activated (On), 5 seconds before the TOT expires, a beep sounds, preventing transmission from being interrupted.
  • (4) TxPow AGC (Automatic Level Control): With this function activated (On), while receiving an extremely strong signal, the TX power automatically reduces proportionally to the strength of the RX signal.
  • (5) Freq Step: 2.5K, 5K, 6.25K, 10K, 12.5K, 20K, 25K, 30K, 50K (9 frequency steps).
  • (6) Ana SQ Level: Adjusts the squelch level to receive signals with different strengths (5 levels offered). This function is only valid for analog channels.
  • (7) Power Save: Turn on to extend battery life. Save 1:1 (work 30ms, dormant 30ms), Save 2:1 (work 60ms, dormant 30ms). May not receive messages in time when power save is on.
  • (8) TBST Sel: TBST frequency (1000Hz, 1450Hz, 1750Hz, 2100Hz) is used to activate dormant repeaters. Press PTT and PF1 key together to transmit the TBST tone.
  • (9) VOX: Enable VOX to speak into the microphone to transmit instead of pressing [PTT] (3 levels provided).
  • (10) VOX Delay: When VOX is enabled, set VOX delay to extend transmission time (0.5sec-3sec, 26 options).
  • (11) Scan Mod: SCM TO (stays 5sec on channel, then resumes scan), SCM CO (stays until signal disappears, resumes 2sec later), SCM SE (terminates scan). Only valid for VFO scan.
  • (12) DTMF Speed: Offers DTMF encode speed (50~500ms) for successful receiver decoding.
  • (13) FM Radio: Turn on or off the FM radio.
  • (14) FM Radio Moni: Radio Mon On (can receive/transmit while FM radio is used), Radio Mon Off (no transmission/reception while FM radio is used).
  • (15) Start Up Pwd: On (set password for startup), Off (no password). Password set in CPS > Optional Setting > Power on Password Char.
  • (16-17) AuRepeater A or B (For VFO A or B): Turn on Auto Repeater function. TX frequency auto increases/reduces based on offset frequency in CPS. Off disables. Positive (TX=RX+Offset), Negative (TX=RX-Offset).
  • (18) Weather Alarm (only US version): Turn On or Off.
  • (19) SMS Format: M-SMS (Motorola DMR), H-SMS (Hytera DMR), DMR Standard (ETSI DMR standard).
  • (20) CTC Ste (Squelch Tail Eliminate): Valid for simplex radio to radio only. Eliminates 'chap' noise at end of analog call.
  • (21) DCS Ste (Squelch Tail Eliminate): Valid for simplex radio to radio only. Eliminates 'chap' noise at end of analog call.
  • (22) No-Signal Ste: Other radios at the same frequency will receive only distorted noises.
  • (23) Time Zone: Set up the time zone of your location.
  • (24) Time Display: Set On to show date/time, Off to hide.
  • (25) Date Time: Time Set (manual date/time adjustment), GPS Check (auto date/time correction with GPS), Format (yy/mm/dd or dd/mm/yy).
  • (26) TxPreamble: Radio transmits preamble before data, SMS, or private call. Settings allow duration adjustment.
  • (27) Header RPT: Radio sends voice header with Group Call ID packet before voice packet. Repeat sending improves synchronization. Settings allow repeat times.
  • (28) CRC ignore: Set ON to enable DMR CRC ignore function. Allows vocoder to selectively ignore CRC result of Voice LC Header, receiving more signals.

7.5.7.2 Chan Set

Channel set menu Route: Main Menu > Settings > Chan Set. The channel set menu will change according to the channel type. When the channel type is digital, it will automatically hide the analog menus.

※Chan Set (Digital Channel)

  • (1) New Chan: Create a new channel and save settings.
  • (2) Delete Chan: Delete the current channel.
  • (3) Channel Type: A-Analog, D-Digital, A+D TX A (mixed analog), D+A TX D (mixed digital).
  • (4) TX Power: Set TX power for current channel.
  • (5) Offset: Adjust offset frequency.
  • (6) Band Width: Only narrow band 12.5KHz for digital channel.
  • (7) RX Freq: Input RX frequency by keypad, save with Menu key.
  • (8) TX Freq: Input TX frequency by keypad, save with Menu key.
  • (9) Talk Around: Communicate directly without a repeater if both radios have Talk Around on.
  • (10) Name: Reset channel name (only in channel mode).
  • (11) TX Allow: Always (always allow transmit).
  • (12) TX Prohibit: TX ON (allow transmit), TX OFF (not allow transmit).
  • (13) Radio ID: In Digital channel, shows DMR ID (programmed in PC software). In Analog channel, shows 5Tone or DTMF self ID.
  • (14) Color Code: Digital channel must have same color code as repeater.
  • (15) Time Slot: Set Slot 1 or Slot 2 for current channel.
  • (16) Digi Encrypt: Digital encryption for confidential communication (32 options).
  • (17) Encrypt Type: Choose normal or enhanced encryption type.
  • (18) RX Group List: Edit RX Group List and assign to channel.
  • (19) Work Alone: Turn on work alone function for current channel. Radio alarms if no confirmation after predetermined time.
  • (20) CH Ranging: Radio automatically starts ranging function when turned to this channel if call contact type is "Private call".
  • (21) APRS Receive: Turn APRS Receive on. Displays other radio's distance and position if both radios have GPS positioned.
  • (22) SMS Forbid: Set On to prohibit radio from receiving SMS.
  • (23) DataAck Forbid: Set On to ignore repeater data service requests.
  • (24) Idle TX: With "Idle TX" ON, radio switches to other time slot if one is occupied. Beeps if both are occupied.
  • (25) DMR Mode: Select different DMR modes for digital channel (Repeater, DMO/Simplex, DCDM/Double Slot, DCDM/TS split).
  • (26) Slot Suit: Radio receives calls from both slots and can call back in corresponding slot.

※Chan Set (Available in Analog Channel only)

When the channel type is analog, it automatically hides the digital menu. The following menus are for analog channels only; unlisted menus are the same as the digital channel.

  • (4) TCDT: Set up the CTCSS/DCS code for the TX.
  • (5) RCDT: Set up the CTCSS/DCS code for the RX.
  • (6) RTCDT: Set up the CTCSS/DCS code for both TX and RX (CTCSS: 62.5Hz~254.1Hz, 51 groups; DCS: 000N~7771, 1024 groups).
  • (7) Optional Signal: Allows setup of DTMF/5TONE/2TONE encode and decode for Analog channels.
  • (10) Squelch mode: Set RX condition when analog channel has CTCSS/DCS decoding and optional signaling.
  • (11) Band Width: Choose wide band or narrow band for analog channel.
  • (12) Reverse: When enabled, RX frequency, TX frequency, and CTCSS/DCS encode/decode are reversed.
  • (13) Compander: Reduces background noise and enhances audio clarity.
  • (14) Scrambler: Offers more confidential communication.
  • (19) Busy Lock: Always (always allows transmissions), RL (not allow transmit when receiving matched carrier but unmatched CTCSS/DCS), BU (not allow transmit when receiving matched carrier).
  • (21) OWN ID: Check radio ID number (set in PC software > Analog > 5Tone or DTMF self ID).
  • (22) DTMF Enc: Set DTMF ID as default call ID for current channel.
  • (23-24) 2Tone Enc: Set 2Tone as default call ID for current channel.
  • (25) 5Tone Enc: Set 5Tone as default call ID for current channel.
  • (26) 5Tone BOT: Set ON to send 5Tone encode ID when pressing [PTT].
  • (27) 5Tone EOT: Set ON to send 5Tone encode ID when releasing [PTT].
  • (28) QDC1200: Set QDC1200 as default call ID for current channel.
  • (29) PTT ID: To get PTT ID working, optional signal must be DTMF or 5Tone, and EOT/BOT set up. OFF, Start, End, Start&End options.

7.6 Device Info

Shows Radio ID, Radio name, serial number, model name, frequency range, firmware version, radio data version, latest program date, picture version, language version etc.

7.7 Record

The voice record is designed for security use. Each call is saved as a separate recording file. Standard voice allows 4 hours of recording in DMR or analog mode.

7.7.1 Turn On/Off the Recording

  1. Press the Menu key to enter the main Menu, press the Up/Down key to Record.
  2. Select Record, then select On/Off to turn on or off the recording.

7.7.2 Play the Record

  1. Press the Menu key to enter the main Menu, press the Up/Down key to Record.
  2. Select List to enter the Record list, select a Record list to enter the Record file.
  3. Select a Record to see the Detailed Information.
  4. Press Select to choose the record option.
  5. Play: Plays one record at a time. Press the Up/Down key to switch records without returning to the previous menu.
  6. Loop Playback: Plays all records in a loop.

7.7.3 Send the Record

  1. Press the Menu key to enter the main Menu, press the Up/Down key to Record.
  2. Select Record List to enter the Record list, select a Record list to enter the Record file.
  3. Select a Record to see the detail information.
  4. Select Send, and it will display the Contact list or Manual Dial.
  5. Select Contact list to choose a contact, press select to send the Record.
  6. Select Manual Dial, input the DMR ID, press the # key to switch group ID or private DMR ID, press select to send the Record.

7.7.4 Recording Manually

In the PC software, Public > Optional Setting > Key function, program a key as Record.

7.8 GPS Positioning Function (Optional with installed GPS)

7.8.1 Turn on GPS

  1. Press the Menu key to enter the main Menu.
  2. Select "GPS".
  3. Select "GPS On".

7.8.2 GPS Mode

Select GPS work mode for positioning use. GPS mode is US Global Positioning System. BDS mode is China BeiDou Navigation Satellite System. GLONASS mode is Russia GLONASS Navigation Satellite System.

7.8.3 GPS Roaming

GPS Roaming function allows the radio to auto switch to a zone when GPS positioning is within the preset radiation radius of coordinates. To get this function working, you need to set the GPS roaming page in the CPS first.

7.8.4 GPS Info

Method 1: Check GPS info from Menu

Press the Menu key to enter the main Menu, select "GPS", then select "GPS Info".

Method 2: Check GPS info from programmed key

In the PC software, Public > Optional Setting > Key function, program a key as "GPS Info", then press the programmed key to check the GPS info.

Note:

  • If the GPS is not positioning, it will display "No Fixed Position", and the GPS icon shows a grey color. Move the radio to an open window or outdoors, and it will take a few minutes to connect to the GPS Satellites.

7.8.5 Send GPS Information

  1. When the GPS is positioning successfully, the GPS icon shows a red color. Follow the above step to check the GPS info, press the edit key to Text edit.
  2. Press Confirm, and it will display Send or Save. If you select Save, the GPS info will be saved as a draft message.
  3. Choose Send and it will display Contact list or Manual Dial.
  4. Select Contact list to choose a contact, press select to send the GPS info.
  5. Select Manual Dial, input the DMR ID, press the # key to switch group ID or private ID, press the Send key to send the GPS info.

7.9 Satellite

This feature allows the radio to communicate with the satellite during its transit.

7.9.1 Location

  • GPS: The satellite function depends on GPS location.
  • Fixed: The satellite function depends on the fixed location beacon, which you need to set up in the CPS-APRS page first.

7.9.2 Satellite

The radio will provide a predict list for the satellites that will transit recently. Select a satellite to check the frequency and transit time. Press the PTT button to transmit to the satellite.

7.10 APRS Location Reporting (Optional, supported by GPS)

7.10.1 Upload Type

  • None: No APRS.
  • Sel A Aprs: Select analog APRS.
  • Sel D Aprs: Select DMR APRS.

7.10.2 Ana APRS

  • PTT Upload: Set the PTT transmit method.
  • Off: Not transmit APRS.
  • Tx Start: Transmit analog APRS when pressing the PTT.
  • TX End: Transmit analog APRS when releasing the PTT.
  • TX Power: Set the transmit power.
  • Band Width: Set the band width for transmitting.
  • TX frequency: Set the transmit frequency.

7.10.3 Digi APRS

  • Signal Path: Set the WIDE format signal path.
  • TX Text: Set the text to be shown on the https://aprs.fi website.
  • PTT Upload: Set the PTT transmit method. Off (not transmit APRS), On (transmit DMR APRS when releasing PTT).
  • Report Channel: Allow user to select a channel to transmit the DMR APRS. Set the 8 report channels in CPS-APRS-Digi page first.
  • Upload Slot: Allow user to select a slot to transmit the DMR APRS. Channel Slot (uses current channel's slot), Slot 1 (use slot 1), Slot 2 (use slot 2).
  • Upload ID: Allow user to set a DMR ID to receive the DMR APRS. Can be a private ID or a group ID.

7.10.4 Digi APRS Info

Received APRS information is saved for look back. Click "Digi APRS Info" to view. Click "Delete All" to clear.

7.10.5 Intervals Set

Allows setting analog APRS or DMR APRS auto transmit at fixed times.

7.10.6 Beacon

  • GPS Beacon: APRS transmits GPS data only if GPS is on and successfully locked to satellites.
  • Fixed Beacon: APRS transmits fixed beacon data. Can transmit without GPS on if fixed beacon location is set in CPS.

Note:

  • More setup options are available via PC software. In CPS-Tools-Options-APRS, check the APRS box to add the APRS menu to the left Digital menu.

(APRS is a registered trademark of Bob Bruninga, WB4APR)

7.11 Digital Monitor

7.11.1 On/Off

  1. Press the Menu key to enter the main menu, press the Up/Down key to choose Digi Moni function.
  2. Press Select to enter Digi Moni menu, press the Up/Down key to choose a sub menu.
  3. On/Off: Off (turn off Digital Monitor), Single Slot (monitor current Slot), Double Slot (monitor Slot 1 and Slot 2).
  4. DigiMoni Cc: Any Cc (monitor any color code), Same Cc (monitor same color code).
  5. DigiMoni Id: Any Id (monitor any TG), Same Id (monitor same TG).
  6. Slot Hold: Off (turn off slot hold), On (turn on slot hold). Recommended for double slot monitoring.

7.11.2 Response and Save a call in Digital Monitor Mode

During Digital Monitor, when receiving a call with an unmatched ID, press the * key. The screen will display "Monitor Response Setup Successfully". Press the [PTT] key to respond to the call. Press the # key. The radio will remind you to choose a Zone. Press the Up/Down key to choose a Zone, then press the select key to save the new channel to the Zone.

8. Reset

  1. Power off the radio first to start the reset function.
  2. Then power it on while holding the [PTT] and the [PF1] button below the PTT at the same time.
  3. The radio will start up with a note on the display – "Are you sure you want to initialize radio?" Press Exit to exit the reset and power on the radio. Press Confirm to proceed with the reset. It will display "Initialize Radio".
  4. After a restart, the radio will display the setting of time zone and the date and time. Use the up-down key to set the current year. Move to the month by pushing the PF1 key. Set the month, and use the PF1 key to move forward each step. Once done, click the Confirm key to save the date and time.

Please remember to set up the time zone to avoid date/time errors. Make sure the codeplug is saved to the PC (CPS) before you perform the update and reset. The codeplug will be eliminated and needs to be installed in the radio.

9. Troubleshooting Guide

ProblemsSolutions
The radio cannot be switched on or no display after being switched on.
  1. Battery pack may not be installed properly. Remove the battery pack and install it again.
  2. Battery power may be insufficient. Recharge or replace the battery pack.
The battery doesn't last very long after charging.The battery is defective; please replace it with a new battery pack.
Cannot talk to or hear other members in your group.
  1. Make sure the frequency and CTCSS are the same as other members.
  2. Make sure you are within range, and not too far away from your member.
  3. Make sure you are set in the correct digital mode and frequency.
  4. In digital mode, make sure to set the correct code and encrypt group in the current channel.
  5. In digital mode, make sure to set the correct receiving contacts and receiving group.
Other voices from non-group members are heard on the channel.Analog: Change the CTCSS/DCS Tone, and make sure to change the tone on all radios in your group.

10. Programming Guide

AnyTone AT-D168UV radios ship from the manufacturer with the “Keypad” locked per FCC rules. You can press the Menu key and the * (star) key to unlock the keypad for the first time of use. You will need the programming cable to connect your radio to your computer and the CPS software for programming.

The programming software and codeplug programming guide are available for download from the AnyTone website: www.anytone.net

When programming this radio for the first time, it is recommended that you first READ the radio with the software and then save this file for future reference, as it contains the default programming and settings. In addition, after you READ this radio with software, first make your programming and frequency changes, then send this edited file back to your radio.

10.1 Multiple Radio IDs

The AT-D168UV radio allows multiple DMR Radio ID numbers to be used. This feature allows one radio to be used, for example, as a Commercial Radio with its own DMR ID, and at the same time also as an Amateur radio with another DMR ID.

In the PC software, Digital/Radio ID List, you can enter your Department Unit Number or Amateur Radio callsign.

10.2 Amateur DMR-MARC

For the best Amateur DMR experience, obtain a subscriber ID from one of many available Amateur Radio sources. A U.S. Amateur can obtain a DMR ID from: https://www.radioid.net/cgi-bin/trbo-database/register.cgi

For DMR repeaters in your area, please see: www.repeaterbook.com

World DMR repeater network map: https://www.repeaterbook.com/index.php/repeater-database

World DMR repeater network with verified Talkgroups by activity: https://brandmeister.network/?page=lh

10.3 Worldwide Amateur Contact Database

The AT-D168UV DMR radios contain a separate database memory for importing and displaying Amateur DMR individual IDs, call signs, and user names in comma-delimited format (.csv).

Please reference the programming guide for import and export database operations detailed.

User List Contact Database: https://ham-digital.org/status/

11. Technical Specifications

Table of technical specifications for the Anytone AT-D168UV radio, including General, Receiving Part, and Transmitting Part details.
Technical specifications for the Anytone AT-D168UV radio.
General
Frequency RangeEuropean: 144-146MHz, 430-440MHz
US: 144-148MHz, 420-450MHz
Channel Capacity4000 channels
Channel Spacing25KHz (Wide Band), 12.5KHz (Narrow Band)
Phase-locked Step5KHz, 6.25KHz
Operating Voltage7.4V DC ±20%
Frequency Stability±1.5ppm
Operating Temperature-20℃ ~ +55℃
Size103.5×53.5×35.5mm (With battery pack)
Weight224g (with battery pack)
Receiving Part
Sensitivity (12dB SINAD)Wide band: ≤0.25μV
Narrow band: ≤0.35μV
Digital Sensitivity0.3uV/-117.4dBm (BER 5%)
0.7uV/-110dBm (BER 1%)
Adjacent Channel Selectivity≥65dB (Wide Band)
≥60dB (Narrow Band)
Spurious Emission≤-57dB
Spurious Rejection≥65dB (Wide Band)
≥60dB (Narrow Band)
Blocking84dB
Hum & Noise≥45dB (Wide Band)
≥40dB (Narrow Band)
Audio Distortion≤5%
Audio Power Output1000mW/16Ω
Transmitting Part
Power OutputVHF: 5/2.5/1W/0.2W
UHF: 4.5/2.5/0.5W/0.2W
Modulation Limit±5.0KHz@25KHz (wide band)
±2.5KHz@12.5KHz (narrow band)
Adjacent Channel Power≥70dB (Wide Band)
≥60dB (Narrow Band)
Hum & Noise≥40dB (Wide Band)
≥36dB (Narrow Band)
Spurious Emission≤-60dBc
4FSK Digital Modulation12.5KHz (data) 7K60FXD
12.5KHz (data+voice) 7K60FXE
Audio Distortion≤5%
Error Rate≤3%

12. Safety Information

The AnyTone AT-D168UV DMR handheld transceiver has been carefully designed to provide you with years of safe, reliable operation. As with all electrical equipment, however, there are a few basic precautions you should take to avoid hurting yourself or damaging the radio:

  • Read the instructions in this handbook carefully. Be sure to save it for future reference.
  • Read and follow all warning and instruction labels on the radio and in the owner's manual.
  • Do not carry the transceiver by the antenna. This may damage the antenna or antenna terminal. Grasp the handheld by its base (not the antenna) when you need to place or remove it.
  • Do not keep the radio with the antenna very close to, or touching exposed parts of the body, while transmitting. AnyTone radios will perform best if you speak 2-4 inches away from the microphone and the radio is vertical.
  • Be sure the "PTT” key is not pressed when you do not need to transmit.
  • Do not operate the radio near unshielded electrical blasting caps or in an explosive atmosphere.
  • Do not transmit without the antenna fitted on the radio. Though it is provided with protection, it may damage the TX output final stage.
  • Respect the environment conditions. The radio is designed to be used in heavy environments, however, avoid exposing it to extremely hot or cold temperatures (outside the range between −20°C to +55°C). Do not expose the transceiver to excessive vibrations as well as dusty or rainy locations.
  • Never try to disassemble or service the radio by yourself (aside from the routine maintenance described in this handbook). It may cause damage to the radio transceiver and void your warranty, requiring extensive repair work. Always contact your local dealer for assistance.
  • Use only authorized accessories. Using non-Anytone radio brand accessories may seriously damage your handheld transceiver and void your warranty.
  • Do not spill liquid of any kind into your radio. If the transceiver gets wet, immediately dry it with a soft and clean cloth.
  • Switch the radio off before you clean it. Follow the directions described in the paragraph "Care and maintenance".
  • Handle the battery properly. Never place the Li-ion battery in your pocket or purse with loose coins. This could result in short-circuiting the battery.
  • Be certain that your power source matches the rating listed for the supplied battery charger (AC adapter). If you are not sure, check with your authorized AnyTone dealer.
  • Avoid damaging the power cable of the battery charger. Do not step on or place anything on it as this could result in a damaged charger power cord. This product complies with the requirements of the Council Directives 89/336/EEC and 73/23/EEC on the approximation of the laws of the member states relating to electromagnetic compatibility and low voltage.

12.1 RF Exposure Warning

Your wireless hand-held portable transceiver contains a low power transmitter. When the Push-to-Talk (PTT) button is pressed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50% TX and 50% RX.

In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless devices. To maintain compliance with the FCC's RF exposure guidelines, this transmitter and its antenna must maintain a separation distance of at least 2 inches from your face. Speak in a normal voice, with the antenna pointed up and away from the face at the required separation distance. The belt clip is for storage purposes only.

AVOID TRANSMITTING ON HIGH POWER WHILE RADIO IS ATTACHED TO YOUR BELT. To transmit, hold the device away from your body and ensure the antenna is at least 2 inches from your body when transmitting.

12.2 EU Notice for End-Users

European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio Licence from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. At this subject, refer to the “EU” specification guide 2014/53/EU.

The European version of these devices is intended for amateur radio use only. It operates on the following bands:

  • VHF = 144-146 MHz
  • UHF = 430-440 MHz

The operator must have the appropriate licence. Any manipulation of the aforementioned frequency bands is prohibited.

12.3 Disposal of Electronic and Electric Equipment

Products with the symbol (crossed-out wheeled bin) cannot be disposed of as household waste. Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste by-products.

In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

13. User Tips

  • Battery Quantity: The package typically includes two batteries (one 1800mAh and one 2600mAh), as listed in the supplied accessories.
  • Programming: This radio requires a programming cable and CPS (Computer Program Software) for full configuration. The software and guide are available on the Anytone website.
  • UHF Frequency Range: The UHF frequency range for the US version is 420-450 MHz.
  • Higher Wattage: This model has an output power of 3W-5W. If you are looking for higher wattage (e.g., 12W-20W) in a handheld, this specific model may not meet that requirement.

14. Online Service and Support

The AnyTone website provides additional information about obtaining service or support for the AnyTone line of two-way radios and accessories. Visit: www.anytone.net

14.1 Warning Notes

Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. AnyTone Radio assumes no responsibility for the results of errors beyond its control. The manufacturer of this equipment also cannot guarantee that changes in the equipment made by non-authorized users will not affect the information in it.

14.2 FCC Licensing Information

This AnyTone radio operates on Commercial / Land Mobile frequencies which require a license from the Federal Communications Commission (FCC) for business, personal, education, and recreational use. To obtain forms, call the FCC forms hotline at: 1-800-418-3676 or go to http://www.fcc.gov

For questions concerning commercial licensing, contact the FCC at 1-888-CALL-FCC (1-888-225-5322).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.