JIKONG JK-BD6A17S8P

Contents

JIKONG JKBMS Active Balance Battery Management System

Model: JK-BD6A17S8P

Instruction Manual

1. Product Overview

The JIKONG Intelligent Active Balance Power Management System (BMS) is a sophisticated management system designed for large capacity series lithium battery packs. It features voltage acquisition, high current active balancing, overcharge, over-temperature protection, coulomb meter, Bluetooth communication, and optional GPS remote functions. This BMS is compatible with Li-ion, Lifepo4, and LTO battery types, supporting configurations from 4S to 24S cells.

The protection board utilizes energy transfer active balancing technology, achieving a maximum continuous balance current of 0.6A. This high current active equalization technology ensures battery consistency, improves battery range, and extends battery life by delaying aging.

The system is supported by a mobile APP compatible with Android, iOS, and HarmonyOS. The APP connects to the BMS via Bluetooth, allowing users to monitor battery status, modify working parameters, and control charge/discharge switches. Its compact size and comprehensive functionality make it suitable for various applications, including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage, base station backup power supplies, and solar power stations.

2. Specifications

The JIKONG BMS is available in 60A and 80A versions, with specific parameters detailed below. The protection board measures 136mm x 103mm x 17.6mm and weighs 260g.

General Specifications

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30-70°C
Maximum Number of Collection Strings24Strings
Maximum Balancing Current0.6A
Protective Plate Size136*103*17.6mm
Finished Weight260g

80A Protection Board Specific Parameters

ParameterValueUnit
Maximum Charging Current80A
Maximum Discharge Current80A
Maximum Instantaneous Current150A
Maximum Internal Loop Resistance1.2mΩ

Default Parameters (Example for LiFePO4)

ParameterLiFePO4 ValueUnit
Balancing Initial Voltage3V
Maximum Balancing Current0.6A
Unit Overcharge Voltage3.6V
Single Overcharge Protection Recovery3.55V
Monomer Undervoltage Protection2.6V
Single Undervoltage Protection Recovery2.65V
Automatic Shutdown Voltage2.5V
SOC-0% Voltage2.6V
SOC-100% Voltage3.5V
Trigger Balancing Differential Pressure0.01V
Charging Overcurrent Protection Delay30S
Charge Overcurrent Protection Release Time60S
Discharge Overcurrent Protection Delay300S
Discharge Overcurrent Protection Release Time60S
Short-circuit Protection Delay5µS
Short Circuit Protection Release Time30S
Charging Overtemperature Protection Temperature70°C
Charge Overtemperature Restore Temperature60°C
Discharge Overtemperature Protection Temperature70°C
Discharge Overtemperature Recovery Temperature60°C
Charging Low Temperature Protection Temperature-20°C
Charge Low Temperature to Restore Temperature-10°C
MOS Overtemperature Protection Temperature100°C
MOS Overtemperature Protection Recovery Temperature80°C

3. Components and Package Contents

The standard package for the JIKONG BMS includes the following items:

  • 1 x BMS unit
  • 1 x Switch (50cm long cable)
  • 1 x NTC temperature sensor (40cm long cable)
  • 1 x Sampling line B (70cm long cable)
  • 1 x Sampling line A (70cm long cable)
Packing list for JIKONG BMS, showing the BMS unit, switch, NTC sensor, and two sampling lines.
Figure 3.1: Packing list for JIKONG BMS, showing the BMS unit, switch, NTC sensor, and two sampling lines.
Activation switch with light and 50cm cable.
Figure 3.2: Activation switch with light and 50cm cable.
JIKONG RS485 Adapter cable, 380mm long, with yellow (A), white (B), and black (GND) wires.
Figure 3.3: JIKONG RS485 Adapter cable, 380mm long, with yellow (A), white (B), and black (GND) wires.

4. Installation and Wiring

The JIKONG BMS is suitable for 7-24 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack.

4.1. General Installation Steps

  1. Connect all necessary cables to the BMS.
  2. Insert the cables securely into their respective ports on the BMS.
  3. Connect the B-line (battery negative) and P-line (load/charger negative) to the battery.

4.2. Device Activation

Before powering on the protection board, ensure the balance cables are properly connected and the P- and B- terminals are correctly wired. Verify that the protection board is securely fixed to the battery cells. Incorrect connections can lead to malfunctions or damage.

The BMS does not have a power-on control switch and is designed for charging activation. After the battery assembly is complete, connect a charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, if you have an optional display screen or activation button, simply connect the cable to the display interface and press the button to activate the BMS.

4.3. APP Installation

The mobile APP for the JIKONG BMS can be downloaded by scanning the QR code below. An Android device requires a minimum of Android Version 7.

QR code for JIKONG BMS mobile APP download.
Figure 4.1: Scan this QR code to download the JIKONG BMS mobile APP.

4.4. Wiring Diagrams

Below are typical wiring diagrams for different battery string configurations. Always refer to the specific diagram that matches your battery pack setup.

Wiring diagram for a 24-string cell configuration, showing connections for P+, P-, B-, motor load, inverter, and charger.
Figure 4.2: Wiring method for 24-string cells.
Wiring diagram for a 16-string cell configuration, showing connections for P+, P-, B-, motor load, inverter, and charger.
Figure 4.3: Wiring method for 16-string cells.
Detailed structural block diagram of the JIKONG Active Balancing Protection Board, illustrating internal components and interfaces.
Figure 4.4: Structural block diagram of the JIKONG Active Balancing Protection Board.
Image showing the rich interface of the BMS with icons for CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, Active Equalizer, and physical ports for GPS, NTC, Sampling port B, Sampling port A, Display/Switch Key.
Figure 4.5: Rich interface to meet daily needs.

5. Operation and Features

5.1. Active Equalization

The BMS employs active equalization technology to transfer energy from high-voltage cells to low-voltage cells, ensuring battery consistency. Before using this function, set basic battery parameters in the APP, including battery type, number of cells, capacity, trigger equalization differential pressure (default is 0.01V), voltage calibration, and current calibration. The default balance current is 0.6A. Users can adjust the balance current based on battery capacity, recommending not to exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP.5.2. Heating Function (Optional)

The optional heating function uses a resistance heater or heating film to warm the battery at low temperatures, preventing performance degradation. The designed heating current is 10A. Users can enable or disable this function via the APP based on ambient temperature. It is recommended to install a temperature control switch (45°C to 65°C normally closed) in series with the heating circuit as a secondary safety measure.5.3. Alarm Function (Optional)

The optional alarm function provides external alerts when the BMS detects safety risks such as overtemperature, overcharge, or overdischarge.

5.4. Battery Parallel Function (Optional)

For energy storage battery packs, the BMS supports an optional parallel function. This requires synchronous use with parallel modules and disabling the 'charging current limiting' function in the APP.

5.5. Protection Features

  • Charge Overvoltage Protection: Standard feature. Users can set single overcharge protection voltage and recovery voltage via the APP. Charging stops if any cell exceeds the set voltage and resumes when all cells are below the recovery voltage.
  • Discharge Undervoltage Protection: Standard feature. Users can set undervoltage protection voltage, recovery voltage, and automatic shutdown voltage via the APP. Discharging stops if any cell falls below the set voltage and resumes when all cells are above the recovery voltage. Automatic shutdown occurs if any cell drops below the automatic shutdown voltage.
  • Charge Overcurrent Protection: Standard feature. Users can set continuous charging current, overcurrent delay, and release time via the APP. Protection triggers if charging current exceeds the set value for the specified delay.
  • Discharge Overcurrent Protection: Standard feature. Users can set continuous discharge current, overcurrent delay, and release time via the APP. Protection triggers if discharge current exceeds the set value for the specified delay.
  • Overtemperature Protection: Standard feature for both charge and discharge. Users can set protection and recovery temperatures via the APP. Charging/discharging stops if temperature exceeds the set value and resumes when it falls below the recovery value.
  • Low Temperature Protection: Standard feature for charging. Users can set protection and recovery temperatures via the APP. Charging stops if temperature falls below the set value and resumes when it rises above the recovery value. For extremely cold areas, using the heating function is recommended.
  • Short Circuit Protection: Standard feature. Users can set short circuit protection delay and recovery time via the APP. Special considerations apply for initial connections to chargers or loads to avoid false triggers due to peak currents.

5.6. Emergency Switch

The BMS includes a standard emergency switch function. When activated via the APP, the protection board will enable both charge and discharge for 30 minutes, providing emergency operational time. This helps prevent situations like being stranded due to battery issues, even if a single cell voltage reaches the automatic shutdown threshold.

5.7. Intelligent Sleep

The intelligent sleep function is a standard feature that allows the BMS to enter a low-power state when idle (charging/discharging current less than 1A for 26 consecutive hours) to reduce self-consumption. The BMS can be reactivated by pressing a button or connecting a charger.

5.8. Communication Function (Optional)

The BMS supports optional CAN and RS485 communication functions. Users can select these based on their requirements and configure the BMS address and communication protocol via the APP. Refer to the Jikong Protection Board communication protocol document for specific details.

6. APP and Display Interfaces

The JIKONG BMS offers various display and interaction options, including a mobile APP, PC software, and dedicated LCD displays.

Multi-screen display options for JIKONG BMS, showing mobile app, PC software, and home storage display interfaces.
Figure 6.1: Multi-screen display and data connection options.

6.1. Mobile APP and PC Software Interface

The mobile APP and PC software allow for intelligent interaction and easy operation. Users can freely adjust multiple protection values such as overcharge, overdischarge, overcurrent, temperature, and balance. To adjust parameters, first read the internal parameters of the protection board, then make changes.

PC software interface for JIKONG BMS, showing real-time data, settings, control options, logging, and fault information.
Figure 6.2: Intelligent interaction and easy operation via PC software.
PC software interface for setting inverter communication protocols, showing supported CAN protocols like Growatt, Voltronic, and WOW.
Figure 6.3: Inverter communication protocol settings via host computer.
Mobile app interface for protocol docking, showing various supported CAN protocols and inverter communication protocols.
Figure 6.4: Protocol docking, fast and convenient via mobile app.

6.2. Dedicated LCD Displays

JIKONG offers various LCD display options to conveniently view battery information such as voltage, current, temperature, and number of strings.

JIKONG 4.3 inch Touch Screen display, showing battery pack total voltage, output current, SOC, cell voltage delta, MOS temperature, alarm status, and average voltage.
Figure 6.5: JIKONG 4.3 inch Touch Screen (Dimensions: 135.9mm x 88.5mm).
Back view of JIKONG 4.3 inch Touch Screen with dimensions (129.4mm x 82mm) and TF Card Holder.
Figure 6.6: Back view of JIKONG 4.3 inch Touch Screen.
JIKONG 3.2 inch Display with 400mm cable and a button to long press to turn on or turn off the BMS.
Figure 6.7: JIKONG 3.2 inch Display.
JIKONG 2.5 inch Display with cables (C, B, A) and instructions for short press to turn on/off the screen and long press to turn on/off the BMS.
Figure 6.8: JIKONG 2.5 inch Display.

7. User Tips

No specific user tips are available from provided reviews or Q&A content at this time. Always ensure all connections are secure and follow the wiring diagrams carefully to prevent damage.

8. Documents and Support

For further detailed information, including comprehensive parameter settings and communication protocols, please refer to the official user manual PDF:

JIKONG Lithium Battery Active Balance Protection Board Maintenance Manual (PDF)

For technical support or inquiries, please contact JIKONG customer service.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.