Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Weintek MT8121iE Human Machine Interface (HMI) Touch Panel. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage or injury.


Safety Information
Failure to follow these instructions may result in damage to the product or personal injury. This manual is for reference only. Please consult customer service or check the official website for information.
Safety Precautions:
- Before installation, wiring, or maintenance, completely cut off the power supply to avoid electric shock and equipment damage.
- The HMI only supports DC 24V power input. Do not connect AC power or incorrect voltage, otherwise permanent damage will occur.
- Please install the equipment in a dry, dust-proof, and oil-mist-free environment. Do not operate in flammable, explosive, or corrosive gas conditions.
- The device must be reliably grounded to ensure anti-interference performance and operator safety.
- Do not touch the screen with sharp tools, hard objects, or wet hands to prevent screen scratching, cracking, and electric leakage risks.
- Do not disassemble or modify the internal structure of the HMI without authorization, otherwise the warranty will be invalid.
- Avoid strong vibration, impact, and direct sunlight long-term irradiation during operation.
- When thunderstorm or unstable power occurs, stop operation and cut off the power to prevent surge damage.
Package Contents
- 1 x HMI MT8121iE Touch Panel (New In Box)
Specifications
| Feature | Specification |
|---|---|
| Display | 12.1" TFT Color |
| Resolution | 1024 x 768 |
| Colors | 16.2M |
| Backlight | LED, >50,000 hours life |
| Brightness | 500 cd/m² |
| Touch Panel | 4-wire precision resistance network |
| Processor | 32-bit RISC Cortex-A8 600MHz |
| Memory | 128M FLASH + 256M RAM |
| USB Host | 1 x USB 2.0 |
| USB Client | 1 x USB 2.0 |
| Ethernet | 10/100 Base-T |
| COM Port | COM1: RS232/RS485 2W/4W, COM3: RS485 2W |
| Rated Voltage | DC 24V |
| Power Down Allow | 3ms |
| Dielectric Strength Test | 500V AC 1 minute |
| Shell Material | ABS |
| Dimensions (mm) | 322 x 243 x 51 mm |
| Cutout Size (mm) | 305 x 231 mm |
| Application | Lathe and Turning Center |
| Certification | CE |
Setup and Installation
Environmental Requirements:
- Install the equipment in a dry, dust-proof, and oil-mist-free environment.
- Do not operate in flammable, explosive, or corrosive gas conditions.
- Ensure the working temperature range is between 0℃ and 50℃. Avoid overheating or ultra-low temperature environments.
- Keep ventilation holes unblocked to prevent internal overheating.
Power Connection:
- The HMI requires a DC 24V power input. Connecting AC power or incorrect voltage will cause permanent damage.
- Ensure the device is reliably grounded for anti-interference performance and operator safety.
Physical Installation:
The HMI unit is designed for panel mounting. Refer to the diagrams below for precise dimensions and cutout requirements.


Wiring:
- All wiring must comply with local electrical safety standards and industrial control specifications.
- Keep communication cables firmly connected. Loose wiring can cause communication interruption, data loss, or system crashes.
Operating Instructions
- After power-on, wait for the system to complete startup before touching the screen to avoid misoperation.
- Operate the touch screen gently. Fierce tapping or pressing may cause touch failure or screen damage.
- Do not plug or unplug communication cables and USB devices during running status to avoid system abnormality.
Maintenance
- Regularly clean the screen surface with a soft dry cloth. Do not use water, alcohol, or chemical solvents to wipe the screen.
- Back up program and data regularly to prevent data loss caused by power failure or equipment failure.
- When the equipment is not in use for a long time, cut off the power supply and store it in a dry and dust-proof environment.
Troubleshooting
- If abnormal screen display, unresponsive touch, or unknown alarm occurs, please power off and restart the device first.
User Tips
No specific user tips were available from provided reviews or Q&A. Always refer to the official documentation for best practices.
For a more detailed guide, you can refer to the User Manual (PDF).
Warranty and Support
Manufacturer Information:
- Manufacturer: SUMTOR(WUXI) ELECTRIC CO.,LTD
- Address: No.118-1 Liangdong Road, Wuxi city, Jiangsu Province, 214000 China
- Phone Number: +8615768369406
- Email: 13802221171@163.com
- Website: http://www.sumtor.com/
EU Authorized Representative:
- Representative: SUCCESS COURIER SL
- Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
- Phone Number: +34910602659
- Email: successservice2@hotmail.com
The EU Authorized Representative acts solely as a representative for cross-border sellers and is not involved in the manufacture, import, or sale of the product. They are not responsible for after-sales services related to the product. Any product quality or infringement issues are the sole responsibility of the manufacturer/importer/seller.
Compliance Information
This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers must assess which requirements and regulations apply based on the actual product type, function, and destination market.