1. Introduction
The ETENWOLF S3C Car Compressor is a versatile and portable tire inflator designed for passenger cars, SUVs, and light-duty pickups. It features a powerful 7800mAh battery, high-speed inflation, and a maximum pressure of 160 PSI. Beyond inflation, it also functions as a power bank and includes multiple LED light modes for convenience and safety.
Key features include:
- Suitable for passenger cars, SUVs, and light-duty pickups.
- 7800mAh battery capacity.
- 22L/Min @ 0PSI (0.75CFM @ 0PSI) high-speed inflation.
- Maximum inflation pressure of 160 PSI (11 bar).
- 100% duty cycle air pump for continuous inflation of large tires.
- 15W PD Fast Charging capability.
- Integrated power bank function.
- 4 preset inflation modes: Car, Bike, Balls, Custom.
- 3 selectable pressure units: BAR, PSI, KPA.
- 3 LED light modes: Illumination, Slow Strobe, SOS.
2. Package Contents
Please check the package for the following items:
- Zephyr S3C Air Compressor x 1
- USB A to C charging cable x 1
- User manual x 1
- Cone shaped blowing nozzle x 1
- Ball needle x 1
- French copper adapter x 1
- T-shaped quick connector x 1
- 15W charger x 1 (for optimal charging)
3. Product Overview
Familiarize yourself with the components of your ETENWOLF S3C Car Compressor:
- Unit Button
- Light Button
- Decrease Pressure Button (-)
- Mode Button
- Start/Pause Power Button
- Increase Pressure Button (+)
- Central Display
- LED Work Light
- Pressure Hose
- Type-C Port (Input)
- USB-A Port (Output)
- Presta Valve Adapter
- Ball Needle
- High-Pressure Conical Nozzle
- Manual Mode
- Car Mode
- Bike Mode
- Ball Mode
- Pressure Unit
- Set Target Value
- Actual Pressure Value
- Battery Level Indicator
- Safety Warning Symbol
4. Setup and Quick Start Guide
4.1. Steps for Inflation
- Remove the pressure hose (09) from its storage channel.
- Insert the nozzle (09) clockwise into the item to be inflated.
- Press the Start/Pause Power button (05) to activate the unit.
- Press the Mode button (04) to switch between the 4 different modes: Manual mode (15), Car mode (16), Bike mode (17), and Ball mode (18).
- Select the desired pressure unit (PSI, KPa, or Bar) by pressing the Unit button (01).
- Press the Decrease Pressure button (03) to lower or the Increase Pressure button (06) to raise the target pressure.
- Press the Start/Pause Power button (05) again to begin inflation.
- The unit will automatically shut off once the item reaches the preset pressure value.
- A Presta valve adapter (12), a ball needle (13), and a high-pressure conical nozzle (14) are conveniently stored on the rear storage panel.
5. Operating Instructions
5.1. Button Operations
- Turn On: Press and hold the Start/Pause Power button (05) for 0.5 seconds.
- Turn Off: When the pump is on, press and hold the Start/Pause Power button (05) for two seconds.
- Pause: While the pump is inflating, you can press the Start/Pause Power button (05) again to pause the unit at any time.
5.2. Automatic Shutdown Conditions
The pump will automatically shut off in the following situations:
- After 3 minutes of inactivity.
- If the charging cable is accidentally disconnected during charging.
- After 5 minutes of inactivity following a full charge.
- After 5 minutes of inactivity when used as a power bank.
- If inflation lasts over 5 minutes, but the actual pressure remains below 5 PSI.
- If inflation lasts over 5 minutes, but the actual pressure exceeds 150 PSI.
5.3. Pressure Setting Memory
Each time you adjust the pressure setting, the compressor will remember your new target pressure and unit setting. This allows you to change the default pressure at any time without re-entering all settings.
5.4. Preset Pressure Values
The smaller number at the top of the display (20) shows the target pressure, while the larger number at the bottom (21) shows the actual pressure value of the inflated object.
| Mode | Adjustable Pressure Range |
|---|---|
| Car Mode | 8.0-130.0 PSI |
| Bike Mode | 10.0-145.0 PSI |
| Ball Mode | 3.0-16.0 PSI |
| Manual Mode | 3.0-160.0 PSI |
5.5. LED Work Light
The LED work light (08) is located at the front of the pump. To turn on the light, first power on the unit by pressing the Start/Pause Power button (05), then press the Light button (02).
The light offers four different settings:
- Strong Flashlight
- Ultra-strong Flashlight
- Slow Strobe Light
- SOS Light
Note:
- The light automatically turns off after 1 hour.
- After the first automatic shutdown, you can manually turn on the LED light again.
- When manually turned on a second time, it will not turn off automatically; it must be turned off manually.
5.6. Power Bank Function
The ETENWOLF S3C can charge your electronic devices such as phones, tablets, laptops, drones, and cameras. It provides a USB-A output of 5V 2A, 10W.
Note:
- To use the power bank function, the pump must be turned on.
- After 3 minutes of charging, the display will only show the battery level to conserve power.
- After 5 minutes, when the connected devices are fully charged, the pump automatically shuts off.
6. Specifications
| Product Name | Air Pump |
| Model | Zephyr S3C Air Compressor |
| Dimensions | 134 x 98.3 x 174 mm (5.28 x 3.87 x 6.85 inches) |
| Inflation Pressure Range | 3.0-160.0 PSI / 0.20-11.00 Bar |
| Operating Temperature | Charging: 0°C-45°C (30°F-113°F) Discharging: -20°C-74°C (-4°F-165°F) |
| Storage Temperature | -10°C~60°C (-14°F~140°F) |
| High-Pressure Air Hose Length | 0.9 meter |
| Battery Capacity | 7800mAh |
| Working Noise | Under 85 dB within 1 meter |
| Input | Type-C: 5V 3A |
| Output | USB-A: 5V 2A |
| Charging Time | 2.5-3.5 hours (with 5V 3A 15W PD charger) Approx. 6 hours (with 5V 2A 10W charger) |
| Continuous Operating Time | Approx. 25 minutes at 20-50 PSI, 25°C ambient, fully charged |
| Sensor Accuracy | ±1 PSI |
| Max Power | 132W |
| Inflating Speed | 22L/min @ 0 PSI (0.75 CFM @ 0 PSI) |
| Cylinder System | High-Efficiency Single Cylinder |
| Material | Plastic |
7. Maintenance
7.1. Battery Charging & Indicator
For optimal charging performance and stability, use a 5V 3A 15W PD charger to charge the built-in battery. Charging from 0% to 100% typically takes 2.5-3.5 hours. If using a 5V 2A 10W charger, it will take approximately 6 hours.
The battery level indicator (22) on the display shows four bars, with each bar representing 25% of the total capacity.
Important Notes:
- The pump cannot be used while it is charging.
- Charge the pump at least once every three months to maintain battery health and performance.
7.2. Pressure Recalibration
Variations in altitude can cause a pressure deviation of 1-3 PSI. If you are at high altitudes (especially above 5000 feet/1524 meters), you can recalibrate the pump's pressure sensor for accuracy.
Steps for Recalibration:
- Turn on the pump using button (05).
- Press and hold the Light button (02) and the Mode button (04) simultaneously for 10 seconds.
- The screen will restart, indicating that the pump has been successfully recalibrated.
Recalibration Notes:
- Ensure the pump is turned off before starting calibration.
- The pressure hose (09) must not be connected to any object during recalibration. Any pressure detected in the hose will prevent the process.
- A charged battery or an external power source is required to perform recalibration.
- New recalibration settings are not permanently saved. When the pump is powered off, the calibration will reset to sea level (0 feet/meter altitude).
8. Troubleshooting
| Problem | Solution |
|---|---|
| Slow inflation speed | Check if the inflated item is leaking. Ensure the air nozzle connection is tight. Inspect inflation hoses for damage. Verify ventilation openings are not blocked. |
| Compressor turns on but does not pump air | Check if the pressure in the item to be inflated exceeds the preset pressure. |
| Cannot increase or decrease preset pressure | Ensure the correct mode is selected and the preset value is within the allowed range. Select Manual Mode and adjust the preset value within the 3-160 PSI range. |
| Pump is inflating, but display shows zero pressure | If air pressure is below 3 PSI, the display will show zero due to the pump's minimum pressure measurement range. |
| Battery indicator not shown after charging | Use a certified ETENWOLF charger or standard charger and the included charging cable. Try charging again. |
| Air leakage when connecting high-pressure hose | Tighten the air nozzle. |
| Cannot charge other devices | Check if the battery has sufficient capacity. Verify the charging device is compatible with 5V 3A output. The compressor cannot be used as a power source while charging. Use the original charging cable. |
| Safety alert symbol (E08) on display | If the problem persists after power cycling, the unit requires factory repair. |
| Display shows error code E10 | Motor fault warning. Motor stops functioning. Should return to normal after 30 seconds of blinking. If persistent, factory repair is recommended. |
| Display shows error code E11 | Low-temperature charging protection. Raise temperature above 0°C for charging to continue. |
| Display shows error code E12 | High-temperature charging protection. Lower temperature below 45°C for charging to continue. |
| Display shows error code E13 | Low-temperature discharge protection. Raise temperature above -20°C for inflation/charging other devices to continue. |
| Display shows error code E14 | High-temperature discharge protection. Lower temperature below 58°C for inflation/charging other devices to continue. |
| Display shows error code E15 | Operating time exceeded. Warning icon blinks for 30 seconds. Check for leaks in the inflated item. |
| Display shows error code E16 | Overpressure protection. Returns to normal after pressure release. |
| Display shows error code E17 | High-pressure operation time exceeded. Warning icon blinks for 30 seconds. Check for abnormal functioning of the inflated item. |
| Display shows error code E18 | Battery damage icon and battery level indicator blink for 30 seconds, then unit shuts down. Unit requires factory repair. |
9. Safety Instructions
Please read and follow these safety instructions carefully to prevent injury or damage:
- This product is not a toy and should not be used by children. Users must be over 16 years old. Keep a safe distance between children and the pump during inflation.
- The product contains a built-in lithium battery. Do not expose the product to fire or dispose of the battery improperly.
- Overheating or water ingress can increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it in a hot car for extended periods. If the pump becomes very hot, there is a risk of explosion.
- Charge the pump at least once every three months to maintain its performance.
- The product has a built-in DC motor that can generate sparks during operation.
- Do not use the product in dusty or gaseous environments that can explode. If unusual noises occur or the temperature becomes very high during inflation, turn off the pump immediately.
- Before setting the inflation pressure, ensure that the correct pressure unit is selected. Confusing PSI and Bar can lead to dangerous over-inflation.
- Unit conversion: 1 Bar = 14.5 PSI; 1 Bar = 100 KPa.
- Do not leave the pump unattended during operation. Use the product in a dry and clean environment. Ingress of sand and dust can damage the product. Do not wash the product with water.
- Ensure to use the ETENWOLF charger or other certified PD chargers and the included charging cable. Malfunctions caused by not following the above requirements are not covered by the warranty.
- To reduce the risk of electric shock, do not expose the product to rain. Store indoors.
10. User Tips
No specific user tips were available from reviews or Q&A content for this product at this time. Always refer to the instructions for optimal use.
11. Warranty & Support
11.1. Warranty Coverage
The ETENWOLF S3C Car Compressor comes with a 2-year warranty from the date of purchase. During this period, we provide timely and efficient online after-sales service. We will repair or replace any product found to be defective due to manufacturing faults.
11.2. Contact Support
For any after-sales inquiries or support, please contact us at:
Email: support@etenwolf.com
We are committed to providing you with professional and efficient service!